ETC Response Mk2 One-Port Bedienungsanleitung

ETC Setup Guide

Response Mk2 One-Port Gateway

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

4268M2220 Rev A Released 2019-07

This guide covers installation and basic setup of the Response Mk2 One-Port Gateway. You can

configure additional software features using the Net3 Concert software from ETC. Reference the Help

system built into Concert for more information. Net3 Concert software can be found at

etcconnect.com/Concert.

Overview

There are two versions of the One-Port Gateway: a wall-mount version and a portable version.

Wall-mount Front View with Faceplate

Touch to

Wake Sensor

OLED screen

Network indicator

Available connectors:

DMX Out (XLR Female)

DMX In (XLR Male)

DMX RJ45

Wall-mount Back View

Wall-mount Front View

button

Down

button

Left

button

Enter

button

Reset

button

Ethernet

Aux power

Termination

switch

Action Buttons

•

Up, Down, Back buttons - The Back button allows you to return to the previous menu or option

and the Up and Down buttons navigate between menu options

•

Enter - The Enter button allows you to advance to the next available menu option or commit a

modified selection

•

Reset - The Reset button provides a physical button to reset the gateway

•

Touch to Wake Sensor - Cover the sensor with your hand to wake the display

LED Indicators

•

Network - Solid green indicates network connection and blinking indicates network activity

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 2 of 8 ETC

Electrical Specifications

The gateways are powered by either auxiliary power or Power over Ethernet (PoE).

•

Auxiliary power input rated voltage of 12-24 VDC, 4 W Max, Polarity Independent

•

10/100Base-T, PoE power Class 1 (IEEE 802.3af)

For auxiliary power, the wall-mount gateway includes a red-and-black wire harness that connects to

the supply conductors using two-position WAGO®connectors. The portable gateway uses a screw

locking DCbarrel connector for use with an external power supply (available separately).

If you supply both PoE and auxiliary power, the gateway defaults to using auxiliary. If auxiliary

power is lost, the gateway will reboot and then begin using PoE.

Note: If you are using an external power supply, it must be rated at a maximum of

15watts.

Connection Options

There are three different connector types available depending on your gateway:

•

DMX Out (five-pin female XLR)

•

DMX In (five-pin male XLR)

•

DMX RJ45 (input or output)

The Response Mk2 Gateways send and receive DMX-512 control signals. DMX cables must be

acceptable for DMX data transmission and connections should follow the standard pinouts per the

charts below. The optional secondary data pair is not used by the Response Mk2 Gateways.

The DMX RJ45 variant can use a standard RJ45 Cat5e cable or better to transmit DMX-512 to other

devices with the same connector.

Note: The DMX RJ45 connector does not function as an Ethernet network port.

Pinouts

Push

1 8

DMX-512

Pinout for

five-pin XLR

DMX-512 Pinout

for RJ45

Pin Use Pin Use Wire

Color

1 Common (shield) 1 Data 1 + w/orange

2 Data - 2 Data 1 - orange

3 Data + 3 not used w/green

4 not connected 4 not used blue

5 not connected 5 not used w/blue

6 not used green

7 Signal Common w/brown

8 Signal Common brown

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 3 of 8 ETC

DMX Termination

Termination is required for all DMX systems and belongs at the source

(beginning) of a DMX line and at the last device physically connected in

the line. A termination switch is located internally for each input/output

and can be configured for DMX termination (IN), No termination (OFF) or

RDM termination (OUT). By default, the DMX termination switch is set to

the appropriate position based on the port type (Female XLR and RJ45 set

to OUT and Male XLR set to IN).

If you need to change the termination setting, perform the following steps:

Termination

switch location

1. Disconnect your gateway from all power supplies.

2. Remove the face plate and gateway from the back

box or portable enclosure. If you are looking at the

back of the gateway, the termination switch is on the

exterior of the right side, beneath the auxiliary power

connector.

3. Set the termination switch to the appropriate

configuration.

About RDM

Remote Device Management (RDM, ANSI E1.20) is a protocol enhancement to DMX-512 that allows

bidirectional communication between a lighting system controller and attached RDM-compliant

responder devices over a standard DMX line. This protocol allows configuration, status monitoring,

and management of these devices.

An RDM Controller is the device that initiates communication with one or more RDM Responder

devices. Examples of responders are RDM-enabled edge devices such as color scrollers, dimmers,

moving lights, and LED fixtures. Compliant DMX-512 and DMX-512-A devices (non-RDM devices)

are fully functional when RDM is present. The Response Mk2 Gateway supports up to 256 total

RDMdevices across its ports using standard DMXsystem design practices.

Note: RDM is currently only supported on DMXOutput ports.

RDM Basics

By default, RDM discovery is not enabled on the gateway. To enable RDM on the gateway, use the

Net3 Concert software or the user interface on the front of the gateway. Please see the Concert

online help files for more information on activating RDM on your gateways or see

Configure

RDMSettings on page 7

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 4 of 8 ETC

Installation

Note: Installation must follow all national and local codes for electrical equipment.

The One-Port gateway is available in a wall-mount (for installation into a back box) and a portable

(pipe, bar or truss mounted) version.

Wall-Mount

For surface-mount applications, ETC recommends using an ETCone-gang surface-mount back box

(part# 1064A1037). For flush-mount applications, use a RACO #695 back box or equivalent

(provided by others). The back box should be installed plumb and square for best results. Ensure that

the box is clean and free of obstructions and that all wiring is installed correctly.

Connect Wiring

Ethernet

Ground wire

Aux Power

Pull all required wiring to the back box, including an

Ethernet cable (Category 5e or better) and ground wire.

Terminate the Ethernet cable using the included kit

(part# 4101A2003). Then connect the termination box to

the gateway using the short male-to-male Ethernet cable

included with the kit.

If you are using auxiliary power, perform the following

steps:

1. Locate the 15 cm (6 in) red-and-black wire harness

that came with your gateway.

2. Using the two-position WAGOconnectors

provided with your gateway, connect the red

(positive) wire to one of them and the black

(negative) wire to another.

3. Run the 24 VDCwires for your auxiliary power to

the WAGO connectors.

4. Plug the two-pin connector on the end of the red-

and-black wire harness into the power supply

terminal connector on the PCB (located directly

above the termination switch on the side of the

gateway).

5. Connect the ground wire to a suitable grounding point.

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 5 of 8 ETC

Install into Back Box

1. Insert the gateway electronics and wiring into the back box.

2. Secure the gateway to the back box using the two screws provided.

3. Align the top of the face plate to the station and angle the bottom approximately 20 degrees.

4. Hook the top of the face plate to the tabs on the top of gateway.

5. Swing the bottom of the face plate down until the magnets engage.

6. If the wall plate does not fully attach, wiggle the bottom of the plate until all the magnets are

seated properly and the plate is secure.

Ethernet

DC power

input

Ground

point

Mounting

bracket

Portable

The portable version of the gateway is designed for easy

setup and can be mounted using the mounting bracket. The

bracket contains holes that accommodate standard

mounting hardware (available separately).

Once you have mounted the portable gateway, connect an

RJ45 cable to the connector on the side of the unit. If you are

not using PoE to power the gateway, connect a compatible

power supply (available separately) to the barrel connector

on the side of the gateway.

If you are not using either a grounded etherCON connector

or DCpower supply, use the ground point to connect the

gateway to a suitable earth ground point.

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 6 of 8 ETC

Gateway User Interface and Configuration

The following sections provide information on basic tasks and configuration that you can perform

from the user interface of the gateway. These tasks and additional configuration can all be

performed using the Net3 Concert application, available from etcconnect.com.

Home Screen Information

The initial screen that your gateway displays is the Home screen. This screen provides the name of

the gateway, the IPaddress and some basic port information. The following is an example of what a

typical home screen might look like.

DMX Gateway

10.101.101.101

1 : Output - Act

Univ 63999

Here, you'll see that the gateway name is DMXGateway, IPaddress is 10.101.101.101 and port 1 is

actively outputting DMXfrom universe 63999.

Pressing the Enter button from the Home screen brings up three selectable menu options (About,

Setup,Operations) from which you can access other information or configuration options.

If attempting to access the Setup or Operations options displays User Interface Locked, your

gateway UI has been locked from the Net3 Concert application. To unlock the UI, reference the

Device Help for Response Gateway Mk2 in Net3 Concert software.

View Device Information

To view information specific to your gateway, select the About menu option from the Home screen.

From the About screen, you can select one of the following four options and then view the

information specific to that option:

General View Levels Port Info RDM Info

Ver: 1.0.0.12

FPGA: 1.0.0

MAC

00:c0:16:00:00:00

Port 1

Channel 1

State Active

Level 127(50%)

Port 1

Mode Output

U: 63999

Speed Max

Port 1

RDM Enabled

Background Off

Devices 128

Configure Network Settings

To configure network settings for your gateway, perform the following steps:

1. From the Home screen, select Setup >Network.

2. From the Mode screen, use the Up and Down buttons to select Manual,Link Local or

Automatic.

•

Automatic attempts to automatically configure the IP Address, IPSubnet and IPGateway for

your device via DHCP.

•

If you select Manual, you must configure the IPAddress, IPSubnet and IPGateway screens

and then select OK from the Apply/Reboot? screen.

•

If you select Link Local, the gateway self-assigns an IPaddress that is valid for the local

network in the link-local address range. Select OK from the Apply/Reboot? screen.

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 7 of 8 ETC

Configure Port Settings

To configure the ports of your gateway, perform the following steps:

1. From the Home screen, select Setup >Ports.

2. Use the Enter button to move from the menu options on the left to the values on the right side

of the screen. Use the Up and Down buttons to change the values and press Enter again to

confirm the change. Using these controls, configure the fields on screen:

•

Port - Select the port for which the following values apply:

•

Mode - Select the port mode. This can be set to Input, Output or Disabled.

•

Universe - Select the Universe of the port (1-63999).

•

HLL - Select whether Hold Last Look (HLL)is on or off. Selecting On enables Hold Last Look

Forever. By default, the output holds for five minutes. Additional configuration options are

available through Net3 Concert.

Configure RDMSettings

To configure RDMfor your gateway, perform the following steps:

1. From the Home screen, select Setup >RDM.

2. Use the Enter button to move from the menu options on the left to the values on the right side

of the screen. Use the Up and Down buttons to change the values and press Enter again to

confirm the change. Using these controls, configure the fields on screen:

•

Port - Select the port for which the following values apply:

•

RDM - Select whether RDMis enabled or disabled on the port.

•

Background - Select whether background discovery and polling of RDM is on or off.

Modify Device Settings

To restore the factory defaults or upgrade the software for your device, select the Operations menu

from the Home screen. From here, you can select the following options:

Restore Defaults - Select OK? from the Restore Defaults screen to restore all default values to your

device. This removes all information that is configured for your gateway.

Restore Defaults

All data

will be lost

OK?

Update Software - Select OK? from the Update Software from server <#.#.#.#> screen if you need

to update the software directly from the gateway.

Note: The recommended method of updating is through UpdaterAtor. Regardless of

whether you update from UpdaterAtor or directly from the gateway, the device must be on

the network.

Update Software

from server

10.101.50.60

OK?

If you do choose to update directly from the gateway, the bootloader runs and the latest software is

downloaded from the server indicated by the <#.#.#.#> IPaddress on the Update Software screen. If

you need to modify this IPaddress, you can configure it in the Net3 Concert application using the

Update Server property.

ETC Setup Guide

One-Port Gateway

One-Port Gateway Page 8 of 8 ETC

Test Port Output

You can test DMX outputs by selecting Operations >Test Output from the Home screen.

CAUTION: Testing outputs drives all DMXlevels to full. Use with caution in a

show situation or when controlling high current devices.

Port 1

State -

Release All

This screen allows you to test the output for any port on your gateway.

•

Port - Press the Enter button to select and then use the Up and Down buttons to cycle through

the ports of your gateway. Press Enter again to select the port.

•

State - Press Enter to select and then use the Up and Down buttons to cycle through the test

state options. If the port is an input, this field displays either Input or Disabled. If the port is an

output, you can select either Released (--), Full or All Zero.

•

Release All - Press the Enter button to release the test state on all ports. Once outputs are set

into a test state they can be released from this menu, from the Net3 Concert application or by

rebooting the gateway.

Note: This product uses licensed software provided by third parties. Please visit

http://www.etcconnect.com/licenses/ for licensing information.

Andere Handbücher für Response Mk2 One-Port

Inhaltsverzeichnis

Andere ETC Tor Handbücher

ETC

ETC Response MIDI Gateway Bedienungsanleitung

ETC

ETC Response Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Response Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC VG-5000 Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC Net 3 Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC DMX/RDM One Port Gateway Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Response SMPTE Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC Net3 Four Port Gateway Bedienungsanleitung

ETC

ETC Response Stücklistenhandbuch

ETC

ETC Response Analog IO Gateway Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung