ETC Source Four jr Bedienungsanleitung

Source Four jr and Source Four jr Zoom • 1

Source Four jr and Source Four jr Zoom

Adjusting the C-clamp

The C-clamp attaches the ﬁxture to the mounting pipe and allows you to adjust the

position of the ﬁxture once it is mounted.

Tightly fasten the C-clamp to the yoke with the yoke bolt and lock washer.

Place the C-clamp on mounting pipe, then tighten the pipe bolt to secure it.

Loosen the C-clamp pan screw and rotate the yoke to the desired position.

Tighten the pan screw to lock the ﬁxture into position.

Adjusting the yoke

To adjust the ﬁxture's position, loosen the yoke locking knob and tilt the ﬁxture to

the desired position. Retighten the yoke locking knob to secure it.

Source Four jr/Zoom's two-position yoke allows you to modify the overall height of

the ﬁxture in the yoke.

To change the yoke position, remove the yoke locking knob, then remove the hex

bolts on either side of the ﬁxture.

Move the ﬁxture to the desired position (

Figure 2

Replace and tighten the hex bolts and the locking knob.

Color frame retaining clip

The color frame holder is equipped with a spring-loaded retaining clip that prevents

color frames and accessories from falling out of the holder.

Caution!

Always hang Source Four jr/Zoom with the color frame retaining clip in

the locked position.

Release the retaining clip by pushing it sideways. The retaining clip will pop open.

Insert the color frame.

Press the retaining clip down until it locks into position.

E T C

Figure 1

Yoke locking

knob

C-clamp

Pan screw

Yoke bolt

Pipe bolt

Yoke

Figure 2

Yoke locking

Clutch disc

Hex bolt

Optional yoke

mounting position

knob

Figure 3

Retaining clip

Unlocked

Locked

PEAK

FLAT

CENTER

Gel frame Barrel Drop-in

Pattern

Yoke

Primary suspension point

Yoke

Lamp housing

Secondary

Shutters

Zoom rear

Beam focus knob

Gel frame holder

Lens tray

Knurled bolt

Center adjustment Peak and ﬂat

retaining clip iris cover

holder slot

locking knob

suspension point

focus knob

(Zoom front focus knob)

Light bafﬂe and

retaining screw

(outer knob) adjustment

(inner knob)

Front view

Back view

2 • Source Four jr and Source Four jr Zoom

HPL lamps

HPL lamps are tungsten halogen lamps.

Verify that the HPL lamp you use is suitable for the voltage at your facility. 230V and

240V HPL lamps are available. Operating HPL lamps above their rated voltage

reduces lamp life and can cause premature lamp failure.

Installing the HPL lamp

The lamp must be installed before you use the ﬁxture.

Caution!

Always replace the lamp if it becomes damaged or thermally deformed.

Disconnect the unit from power before installing and replacing the lamp.

Loosen the knurled bolt on the back of the lamp housing and pull the housing

straight out.

Remove the HPL lamp from its box, holding it by the base.

Note:

To avoid premature lamp failure, do not touch the lamp glass. If you do

touch the lamp, clean it carefully with rubbing alcohol and a clean, lint-free

cloth before operation.

Line up the ﬂat sides of the lamp base with the retention brackets on either side

of the socket. See

Figure 4

Push down on the lamp base until the lamp seats ﬁrmly. (The top of the lamp

base will be even with the top edges of the retention brackets when it is properly

installed.)

Caution!

Improperly installed lamps cause premature lamp failure and socket

problems.

Press lamp retainers down across lamp base and clip securely.

To reinstall the lamp housing, line up the side ﬁns and the bolt hole, then tighten

the knurled bolt to secure the housing.

Aligning the lamp

Use the two concentric knobs on the rear of the lamp housing to align the lamp. The

outer knob centers the lamp within the reﬂector and locks it in position; the inner

knob ﬁne tunes the ﬁeld. See

Figure 5

Note:

The ﬁxture must be on to align the lamp.

Unlock the outer knob by turning it counterclockwise one turn.

Gently push the outer knob from side to side and up and down until the lamp is

centered in the ﬁeld.

Once the lamp is centered, tighten the outer knob to lock it in place.

Turn the inner knob right or left to adjust for optimum ﬂat ﬁeld.

WARNING!

Do not use lamps other than the HPL in Source

Four jr/Zoom ﬁxtures.

Use of lamps other than HPL will void

UL and cUL safety conformity and warranty.

Lamp code Watts Volts Color temperature Average rated life

HPL 375/115 375 115 3,250ºK 300 hour

HPL 375/115X 375 115 3,050ºK 1,000 hour

HPL 550/77 550 77 3,250ºK 300 hour

HPL 550/77X 550 77 3,050ºK 2,000 hour

HPL 575/115 575 115 3,250ºK 300 hour

HPL 575/115X 575 115 3,050ºK 2,000 hour

HPL 575/120 575 120 3,250ºK 300 hour

HPL 575/230 575 230 3,200ºK 400 hour

HPL 575/240 575 240 3,200ºK 400 hour

WARNING!

Let lamp cool before changing.

American

Euro.

HPL lamp

Lamp

Knurled boltLamp housing

Lamp

retention

brackets

retainers

Figure 4

Figure 5

Lamp housing Knurled bolt

Center Peak and ﬂat

adjustment

(outer knob)

adjustment

(inner knob)

Source Four jr and Source Four jr Zoom • 3

Focusing the beam

On a ﬁxed ﬁeld angle Source Four jr, with a 26

, 36

or 50

lens, adjust the lens posi-

tion to focus the edge of the beam. On a Source Four jr Zoom, adjust the position of

both lenses to set the beam's spread and to focus the edge of the beam. The Zoom

lenses give you a range from 25

to 50

Loosen the beam focus knob(s) on the underside of the barrel. See

Figure 6

Slide the lens(es) forward or backward to achieve the desired beam edge.

Once the ﬁxture is focused, tighten the beam focus knob(s).

Gel notes

For best results, always use a high quality, high temperature color medium. ETC

does not guarantee performance with low temperature, saturated color gels.

Shaping the beam

You may shape the beam with the shutters, a pattern, or an optional drop-in iris (ETC

part #7062A1011). See

Figure 7

Pattern projection

The pattern holder slot is on the top side of the barrel, immediately in front of the

shutters. It accommodates the M-size pattern holder shown in

Figure 8

. The M-size

pattern holder’s handle should bend away from the shutter handle at a 30

angle. If

your pattern holder’s handle is straight, you may bend it far enough to not interfere

with the action of the shutter handle.

Use an optional donut (ETC part #7060A1037) in the accessory holder to enhance

pattern projection.

Drop-in iris slot

The drop-in iris slot is on the top side of the front barrel, immediately in front of the

pattern holder slot. See

Figure 9

. When it is not in use, a small sheet metal cover

secured with two crosshead screws prevents light leakage and retains the iris

assembly. To install an iris, follow these steps.

Caution!

Be certain the ﬁxture is not hot before installing the iris.

Use a crosshead screwdriver to loosen the screws on the drop-in iris slot cover.

Do not remove the screws.

Slide the cover completely forward, exposing the slot.

Insert the iris. The ﬂat side must be toward the shutters and the iris handle

should extend out of slot.

Slide the slot cover back toward the shutters until it meets the iris handle. Leave

enough space to move the iris handle. Tighten the screws.

Switching lens assemblies

Follow these steps to replace a ﬁxed ﬁeld angle lens with Zoom lenses.

Loosen the screw at the front of the light bafﬂe. See

Figure 10

Pull the light bafﬂe out of the barrel.

Remove the beam focus knob from the bottom of the barrel and slide the lens

assembly from the barrel.

Slide the Zoom lens rear assembly into the barrel and install its beam focus knob.

Slide the Zoom lens front assembly into the barrel and install its beam focus

knob.

Slide the light bafﬂe back into place.

Replace and tighten the screw at the front of the light bafﬂe.

Note:

Reverse this procedure to replace Zoom lenses with a standard lens.

Figure 6

Beam focus knob

Color frame

Figure 7

Iris

(ETC part # 7062A1011)

Figure 8

M-size pattern holder

(ETC part # 7062A1010)

Figure 9

Drop-in

Pattern holder slot

iris slot

Figure 10

Lens tray with

safety screen

Light bafﬂe and

retaining screw

Electronic Theatre Controls

North America

3030 Laura Lane • Middleton, Wisconsin 53562 • USA • Tel: (+1) 608 831 4116 • Fax: (+1) 608 836 1736

Europe

5 Victoria Industrial Estate • Victoria Road • London W3 6UU • Tel: (+44) 181 896 1000 • Fax: (+44) 181 896 2000

Asia

Room 605-606 • Tower III • Enterprise Square • 9 Sheung Yuet Road • Kowloon Bay • Hong Kong • Tel: (+852) 2799 1220 • Fax: (+852) 2799 9325

World Wide Web:

http://www.etcconnect.com •

Email:

[email protected]

Specifications subject to change. Source Four jr and Source Four jr Zoom are protected by US patent numbers 5,446,637 and 5,268,613. Japanese Patent

2,501,722.

US and International Patents Pending. 7062M1001.

Revised 11/98.

Cleaning lenses

Caution!

Change lenses if they become visibly damaged to the extent that their

effectiveness is impaired, for example, by cracks or deep scratches.

Remove the lens assembly. (See

Switching lens assemblies,

above, steps 1-3.).

Remove safety screen.

Dampen a clean, lint-free cloth with vinegar or household ammonia. You may also

use water, but it will leave spots which you may remove by polishing the lens

gently with a clean, dry cloth.

Starting from the center, gently wipe the lens.

Replace safety screen.

Replace the lens assembly.

Accessories

WARNING!

Never use glass and window cleaner or any abrasive material to

clean lenses. Glass and window cleaners will stain the lens surface. Abrasive

materials (such as steel wool) will damage lenses.

Pattern holder, M-size 400PH-M

6.25” (15.875cm) donut 400DN

6.25" (15.875cm) top hat 400SN

6.25" (15.875cm) color frame 400CF

Drop-in iris assembly 400JRS

30" (76.2cm) safety cable, black 400SC

C-clamp 400CC

50º lens assembly 450JL

36º lens assembly 436JL

26º lens assembly 426JL

Zoom lens front assembly 42550FLT

Zoom lens rear assembly 42550RLT

Zoom lens assembly set 42550ZLS

Color extender 400GE

Andere Handbücher für Source Four jr

Dieses Handbuch passt für folgende Modelle

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Source Four LED Series Installationsanleitung

ETC

ETC HIGH END SYSTEMS SolaPix 37 Bedienungsanleitung

ETC

ETC ColorSource Spot jr v2.0 Bedienungsanleitung

ETC

ETC ColorSource CYC Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

ETC

ETC Lighting Control Console Bedienungsanleitung

ETC

ETC Desire D60 XTI Bedienungsanleitung

ETC

ETC Selador Series Bedienungsanleitung

ETC

ETC Express Bedienungsanleitung

ETC

ETC CE Source Four Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Prodigy FlyPipe Studio Bedienungsanleitung

ETC

ETC ArcSystem Pro One-Cell Series Bedienungsanleitung

ETC

ETC GDS CueSystem Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC SolarFrame 750 Bedienungsanleitung

ETC

ETC D22 Desire series Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC Sensor IQ Contact Input Control Option Card Bedienungsanleitung

ETC

ETC High End Systems SolaFrame 3000 Bedienungsanleitung

ETC

ETC Desire Fresnel Bedienungsanleitung

ETC

ETC Source Four Mini CE Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung