ETC Sensor IQ Contact Input Control Option Card Bedienungsanleitung

ETC Installation Guide

Sensor IQ Contact Input Control Option Card

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETC intends this document to be provided in its entirety.

7131M2170 Rev C Released 2020-06

Overview

The Sensor IQ Contact Input Option Card (IQ-CI) provides the ability to directly control the circuits using a

momentary or maintained dry contact input. This document details the installation of this card in the

Sensor IQ Intelligent Breaker Panel.

Installation

The Contact Input Option Card can be installed on either interior wall of the low voltage

cavity.

1: There are four plastic standoffs included with the option card kit. Align the standoffs with the

mounting holes on the option card so the fins are located opposite the connectors.

2: Press gently until the plastic tabs pass through the mounting hole, locking into place.

3: Align the standoffs with the mounting holes on the interior of the low voltage cavity.

4: Press gently until the plastic tabs pass through the mounting hole, locking the option card into place.

Connect Wiring

The Contact Input Option Card provides four bus connections for termination of up to 24 individual dry

contact inputs. A pluggable screw connector is provided for each input and accepts 4–1 mm2(12-18 AWG)

Class 2 wire. Each connector is labeled to assist in relay referencing during termination.

1: Pull wire from the device supplying the contact closure into the Sensor IQ through the low voltage

trough. Reference the

Sensor IQ Installation Manual

for cable routing and conduit access

information.

Note:

It is best to install any panel option kits after conduit rough-in and load wiring

terminations are complete to reduce the likelihood of damage to the option card. For

additional information on panel installation, reference the

Sensor IQ Installation Manual.

All ETC documentation is available for free download at

etcconnect.com

Standoff

Mounting

hole

Contact Input

Option card

Install option card on

either interior wall.

Fins

ETC Installation Guide

Contact Input Option Card

Contact Input Control Option Card Page 2 of 2 ETC

2: Strip the insulation from each wire pair back 6 mm (1/4 in).

3: Remove the pluggable screw connector header on the Contact Input board.

4: Using a 3 mm (1/8 in) flatblade screwdriver, loosen the terminals and insert each of the data + and

data - wire set into the appropriate terminal for the circuit.

• Data wires in the set are polarity-independent.

5: Tighten each screw terminal until the wire is held snugly.

6: Repeat steps 4 and 5 for the remaining dry contact closures.

7: Replace all pluggable screw connectors onto the contact input board.

Connect the Wire Harness

1: Noting connector orientation, plug one

end of the wire harness (supplied with

the option kit) into the connector on the

option card.

2: Noting connector orientation, plug the

second end of the wire harness into the

connector found on the circuit board

mounted on the inside rear of the panel.

Remove the Option Card

1: Use a small pliers to compress the plastic

tabs on the mounting pins.

2: While the tabs are compressed, gently

pull the option card away from the panel.

Programming

The Contact Input Option Card is programmable through the relay panel user interface.

1: Press the [Enter] () button on the user interface to access the Main Menu.

2: Navigate to Arch Setup > Contact Inputs.

When the Contact Input card is installed, you will have the following options within the Contact Input

menu.

•Contact: Displays the number of contacts being configured, 1–24.

•Evaluate on boot: If set to Yes, the contact state will be evaluated on boot and the action configured

for that state will be performed at boot.

•Space: Determines the space in which the selected action will happen.

•On Open: Determines the action that occurs when the contact is opened. The following options are

available:

-None: No action will be taken when the contact opens.

-Off: Off will be activated in the selected space when the contact opens.

-Preset: The selected preset will be activated in the selected space when the contact opens.

-Sequence: The sequence will be activated in the selected space when the contact opens.

-Output to Full: The selected output range will be driven to full when the contact opens.

-Output to 0%: The selected output range will be driven to 0% when the contact closes.

•On Close: Determines the action that occurs when the contact is closed. The same actions are

available as listed above.

For additional information on Contact Input card setup and programming, reference the

Power Control

Processor Configuration Manual

. ETC documentation is available for free download at etcconnect.com.

Option card

connections

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Sensor IQ DALI Control Option Card Bedienungsanleitung

ETC

ETC Aero Wave Station Bedienungsanleitung

ETC

ETC High End Systems SolaFrame 3000 Bedienungsanleitung

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC Source Four Zoom Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC ColorSource Spot jr v2.0 Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Cyberlight LED Bedienungsanleitung

ETC

ETC ArcSystem Pro One-Cell Series Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC GDS BluesSystem Bedienungsanleitung

ETC

ETC ColorSource CYC Bedienungsanleitung

ETC

ETC Source Four jr Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC HIGH END SYSTEMS SolaPix 37 Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC Desire D40XTI Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung