ETS MKS-RPSG Bedienungsanleitung

MKS-RPSG Microphone Kill Switch Instructions

The MKS-RPSG is a device designed to mute an ETS SM1 series microphone with up to 169 memorized proximity

keychain fobs. It is typically used for privacy and confidentiality purposes. Applications include interview rooms,

Interrogation rooms, hospital rooms and patient exam rooms. The MKS-RPSG is placed in-line with an ETS microphone

and interface device or IP camera audio input. When the microphone enabled,

Mounting

The MKS-RPSG is designed to be mounted on a single gang electrical box.

Cable connections

Run 22 gauge 2 conductor shielded between the SM1 series microphone and MKS-RPS. Run another cable of the same type between

the MKS-RPSG and the ETS interface box. Both cables combined length should not exceed 1000’. If not using an ETS interface note

that power and audio have a common connection to the COM terminal. See figure below.

LED microphone mute indicator

The LED on the proximity reader is green when the microphone is enabled and red when the microphone is disabled.

Programming fobs

Up to 169 fobs can be stored in the reader. Adding fobs to the reader can be done one of two ways. Method 1:

Momentarily press the ‘1S CARD /10S ERASE’ button on the board inside the unit, The reader will beep once and the

LED will flash red and green several times then present the fob to the reader until it beeps. The reader will beep twice and

the LED will flash red and green several times. To add another fob repeat this process.

The second method of adding fobs is to present any fob to the reader that is already memorized by the reader, then after

the beep, within 5 seconds, present the fob to reader that is to be added. The reader will beep a total of 3 times indicating

the card has been memorized.

Deleting fobs: Fobs cannot be individually deleted from the reader data base. The only way to delete fobs is to delete

them all then add the desired fobs back in. To delete all fobs in the reader, hold the ‘1S CARD /10S ERASE’ button down

until you see the LED flash red and green 10 times and beep. Then to start adding cards, you must first use the first

method of adding fobs described above to memorize the first fob.

Warranty

All ETS products carry a one year parts and labor warranty. This warranty does not cover damages as a result of misuse, improper

handling of the unit or exposure to extreme temperatures or moisture. At its discretion, ETS reserves the right to repair or replace this

unit under the conditions of the warranty. If you experience problems with your equipment call ETS at: 505-888-3923 to obtain a return

authorization number. Equipment requiring repair beyond the warranty period or units that have been damaged or are not covered

under the warranty can be repaired by ETS for a minimal cost under most conditions.

Made in USA

Inhaltsverzeichnis

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung