EuroLite 50531140 Bedienungsanleitung

USER MANUAL

No. 50531145 Receiver

Wireless remote control for single- and multi-colored LEDs 12-24 V

LED Strip 4in1 Zone RF Controller

No. 50531140 Set (receiver and remote control)

www.eurolite.de

•

Thank you for purchasing this LED control system. The wireless

receiver is especially designed for control of single- and

multi-colored (C + , RGB, RGB ) LED strips requiring an

operating voltage of 12 V and 24 V direct current. The receiver is

operated by wireless control (2.4 GHz) via the remote control. 4

control zones are available. Multiple receivers can be assigned to

the zones as desired and controlled via the same remote control,

either separately or in groups. As the receivers forward the radio

signal, a large range can be covered and all color settings run in

sync. The maximum power consumption of a channel must not

exceed 6 A and of all LEDs connected 24 A. The connection must

be made by skilled personnel only. Please read these operating

instructions carefully before using the product. They contain

important information for the correct use of your product. Please

keep them for future reference.

SAFETY INSTRUCTIONS

•

Only use the product according to the instructions given herein. Damages due to

failure to follow these operating instructions will void the warranty! e do not assume

any liability for any resulting damage.

•

e do not assume any liability for material and personal damage caused by improper

use or non-compliance with the safety instructions. In such cases, the

warranty/guarantee will be null and void.

•

Unauthorized rebuilds or modifications of the product are not permitted for reasons of

safety and render the warranty invalid.

•

This product is not a toy. Keep it out of the reach of children. Do not leave packaging

material lying around carelessly.

•

Keep this device away from rain and moisture. Indoor use only.

•

Protect the product against excessive humidity and heat. The recommended

temperature is -5 to +45°C.

•

Before taking into operation, check upon possible damages. If defective, the product

must not be taken into operation.

•

This product is maintenance-free, except for occasional cleaning. You can use a

slightly dampened cloth for cleaning. Never use alcohol or solvents.

•

Maintenance and service operations are only to be carried out by authorized dealers.

INSTALLATION

•

Overview

Setup

•

Install the receiver in a suitable spot and remove the covers from the terminals.

•

Connect the LEDs to the negative and positive OUTPUT terminals (V+ = common positive pole,

V- = see figure on next page). The load by the LEDs must not exceed 6 A per channel. The

overall load must not exceed 24 A to avoid damage to the receiver.

•

For power supply, connect a regulated power supply unit (min. 12 V, max. 24 V) to the negative

and positive INPUT terminals.

•

Use the DIP switches to select the operating mode according to the connected LEDs:

RGB RGB DIM CCT

•

Screw on the covers with the screws provided.

•

For power supply of the remote control, insert two 1.5 V AAA batteries into the battery

compartment as indicated.

•

For operation the receiver needs to be assigned to the remote control (see chapter “ ireless

Connection” on page 4).

DIP switch to select LED type

Power connection: 12-24V DC Connectors for LEDs

INSTALLATION

•

Application example 1: Single-color LEDs

V+→V+, CH1→V‒, CH2→V‒, CH3→V‒, CH4→V‒

Application example 2: White LEDs CW+WW) with variable color temperature

V+→V+, CH1→C , CH2→ , CH3→C , CH4→

Application example 3: RGB LEDs

V+→V+, CH1→R, CH2→G, CH3→B, CH4→not connected

Application example 4: RGBW LEDs

V+→V+, CH1→R, CH2→G, CH3→B, CH4→

WIRELESS CONNECTION

•

For the remote control to work together with the receiver, the two devices first have to be paired.

There are four separate control zones. Multiple receivers can be assigned to the four zones as

desired and controlled with a mutual remote control. The receivers can be operated in different

modes so it is possible to operate each zone with different LED types. The functions of the

remote control change according to the set operating mode of the respective receiver.

If multiple receivers are used in the same control zone, the receivers exchange signals among

each other. As a result, all dynamic and static color settings run in sync and there is no visible

difference to a wired system.

Please note:

1) The devices are not paired by default. Each remote control has its own code. To avoid

interferences during operation, the devices need to be paired manually during installation.

2) The receiver can be assigned to only one code at a time and needs to be reset to factory

settings before a new code can be assigned.

3) As the receiver has to be switched on for assigning a code, multiple devices can be

configured simultaneously. In this case, we recommend separately switchable sockets for

different areas of the installation so that certain areas can remain switched off during the

configuration process.

remote control (20 meters)

receiver (10 meters)

WIRELESS CONNECTION

•

Pairing the remote control with the receiver

hen paired, the receiver can be controlled via the remote control.

Step Procedure Remarks

1 Connect the LEDs and switch on the

receiver.

1) If the receiver has been paired before,

it has to be reset to factory settings

before it can be paired again.

2) Provided that they are within the range

of the remote control, multiple

receivers can be configured

simultaneously.

2 Select a control zone.

Select the desired control zone using the

ZONE button on the remote control. The

respective indicator lights.

Keep the ON button pressed for 5

seconds to switch to pairing mode. The

RF indicator now flashes rapidly.

The pairing process is automatically

terminated after 60 seconds or by

pressing any button.

4 The connected LEDs flash three times

and then return to their previous state.

The devices have been paired

successfully.

Resetting the receiver

After being reset to factory settings, the receiver can be paired with a new remote control.

Step Procedure Remarks

1 Connect the LEDs and switch on the

receiver.

1) The receiver should be reset within 60

seconds after power on.

2) Provided that they are within the

range of the remote control, multiple

receivers can be configured

simultaneously.

Keep the OFF button pressed for 5

seconds to initiate the resetting

process. The RF indicator now flashes

rapidly.

1) It is not necessary to select a certain

control zone.

2) The resetting process is automatically

terminated after 60 seconds or by

pressing any button.

3) Any remote control can be used to

reset the receiver.

3 The connected LEDs flash three times

and then return to their previous state.

The receiver has been reset to factory

settings successfully.

WIRELESS CONNECTION

•

Pairing multiple remote controls

Each remote control is delivered with its own code preconfigured. If you use multiple remote

controls, the code of one remote control needs to be copied to the other remote controls for

them to operate in sync successfully.

Step Procedure Remarks

Keep the ON button on the master

remote control pressed for 5 seconds to

switch to copying mode. The RF indicator

now flashes rapidly.

The copying process is automatically

terminated after 60 seconds or by

pressing any button.

Take the remote control you wish to copy

the code to and keep the M(ODE) button

pressed for 5 seconds. The RF indicator

switches from 100% brightness to 0%

and flashes. The copying mode has been

activated.

The copying process is automatically

terminated after 30 seconds or after the

code has been copied successfully.

The RF indicator on the remote control

the code has been copied to flashes

three times.

The code has been successfully copied

to the new remote control. The device

now automatically quits the copying

mode.

Copying the code from receiver to remote control

Codes can also be copied from a receiver to a remote control, e.g. if the previously used remote

control was lost and needs to be replaced.

Step Procedure Remarks

1 Switch off the receiver.

Keep the M(ODE) button on the remote

control pressed for 5 seconds. The RF

indicator switches from 100% brightness

to 0% and flashes. The copying mode

has been activated.

The copying process is automatically

terminated after 30 seconds or after the

code has been copied successfully.

3 Switch on the receiver. The RF indicator

on the remote control flashes three times.

The code has been successfully copied

to the new remote control. The device

now automatically quits the copying

mode.

Notes:

1) The distance between receiver and remote control should not exceed 2 meters during this

procedure.

2) During the copying process, all information of the entire system is being transmitted. It is not

necessary to repeat the procedure for different control zones.

Resetting the remote control

The remote control can be reset to factory settings.

Step Procedure Remarks

1 Keep the M(ODE) button pressed for 20

seconds.

The RF indicator is dimmed down and

flashes while the M(ODE) button is

pressed. After releasing the button, the

indicator lights with 100% brightness

again, indicating that the resetting

process has been activated.

2 Confirm with OFF button. The RF

indicator flashes three times.

The remote control has been reset to

factory settings successfully.

OPERATION

•

Single-color LEDs

If the DIP switch has been set to the operating mode DIM, the following functions can be

controlled with the remote control. The remote control switches to stand-by mode after 8

seconds of inactivity and can be reactivated by pressing any button.

Button Function

No function

Power on

Power off

Dimmer ring

Adjusting brightness clockwise

Mode selection: flashing, fade

Reduce brightness by 10% (Nightlight function)

Reduce brightness in 5

levels

(10 %, 30 %, 50 %, 70 %, 100 %)

Increase brightness in 5

levels

(10 %, 30 %, 50 %, 70 %, 100 %)

Reduce brightness in 1024

levels

(Keep button pressed to proceed quicker)

Increase brightness in 1024

levels

(Keep button pressed to proceed quicker)

Reduce speed for dynamic programs in 100

levels

(Keep button pressed to proceed quicker)

Increase speed for dynamic programs in 100

levels

(Keep button pressed to proceed quicker)

Select zones 1-

4 (status indicator lights),

keep pressed for 2 seconds to select all zones (all status indicators light)

RF signal indicator

Mode

Brightness + (5 levels)

Brightness + (1024 levels)

Speed +

Zone indicators

SET

OFF

Dimmer ring

Nightlight

Brightness ‒ (5 levels)

Brightness ‒ (1024 levels)

Speed ‒

Zone selection

(keep pressed for 2 seconds

for all zones)

OPERATION

•

White LEDs with variable color temperature

If the DIP switch has been set to the operating mode CCT, the following functions can be

controlled with the remote control.

Button Function

No function

Power on

Power off

Color ring

Set color temperature between 100% cold white and 100% warm white

Mode selection: flashing, 2-color flashing, fade, 2-color fade

Reduce brightness by 10% (Nightlight function)

Reduce brightness in 5

levels

(10 %, 30 %, 50 %, 70 %, 100 %)

Increase brightness in 5

levels

(10 %, 30 %, 50 %, 70 %, 100 %)

Reduce brightness in 1024

levels

(Keep button pressed to proceed quicker)

Increase brightness in 1024

levels

(Keep button pressed to proceed quicker)

Reduce speed for dynamic programs in 100

levels

(Keep button pressed to proceed quicker)

Increase speed for dynamic programs in 100

levels

(Keep button pressed to proceed quicker)

Select zones 1-

4 (status indicator lights),

keep pressed for 2 seconds to select all zones (all status indicators light)

RF signal indicator

Mode

Brightness + (5 levels)

Brightness + (1024 levels)

Speed +

Zone indicators

SET

OFF

Color ring

Nightlight

Brightness ‒ (5 levels)

Brightness ‒ (1024 levels)

Speed ‒

Zone selection

(keep pressed for 2 seconds

for all zones)

OPERATION

•

RGB LEDs

If the DIP switch has been set to the operating mode RGB, the following functions can be

controlled with the remote control.

Button Function

No function

Power on

Power off

Color ring

Color selection (64 colors available)

Mode selection (8 modes available, see table below)

hite light on/off

Select 6 static colors (cyan, purple, yellow, blue, green, red)

Select 6 static colors (red, green, blue, yellow, purple, cyan)

Reduce brightness in 1024 levels (keep button pressed to proceed quicker)

Increase brightness in 1024 levels (keep button pressed to proceed quicker)

Reduce speed for dynamic programs in 100 levels

(Keep button pressed to proceed quicker)

Increase speed for dynamic programs in 100 levels

(Keep button pressed to proceed quicker)

Select zones 1-

4 (status indicator lights),

keep pressed for 2 seconds to select all zones (all status indicators light)

Mode Function Remarks Mode Function Remarks

1 Pulsating white Speed

adjustable,

brightness not

adjustable

5 7 colors fade Speed

adjustable,

brightness not

adjustable

2 3 colors change 6 Fade R/G

3 7 colors change 7 Fade R/B

4 3 colors fade 8 Fade G/B

RF signal indicator

Mode

6 basic colors

Brightness + (1024 levels)

Speed +

Zone indicators

SET

OFF

Color ring

hite

6 basic colors

Brightness ‒ (1024 levels)

Speed ‒

Zone selection

(keep pressed for 2 seconds

for all zones)

OPERATION

•

RGBW LEDs

If the DIP switch has been set to the operating mode RGB , the following functions can be

controlled with the remote control.

Button Function

No function

Power on

Power off

Color ring

Color selection (64 colors available)

Mode selection (8 modes available, see table below)

hite light on/off

Reduce brightness of white light in 1024 levels (keep button pressed to proceed quicker)

Increase brightness of white light in 1024 levels (keep button pressed to proceed quicker)

Reduce brightness of RGB light in 1024 levels (keep button pressed to proceed quicker)

Increase brightness of RGB light in 1024 levels (keep button pressed to proceed quicker)

Reduce speed for dynamic programs in 100 levels

(keep button pressed to proceed quicker)

Increase speed for dynamic programs in 100 levels

(keep button pressed to proceed quicker)

Select zones 1-

4 (status indicator lights),

keep pressed for 2 seconds to select all zones (all status indicators light)

Mode Function Remarks Mode Function Remarks

1 Pulsating white Speed

adjustable,

brightness not

adjustable

5 7 colors fade Speed

adjustable,

brightness not

adjustable

2 3 colors change 6 Fade R/G

3 7 colors change 7 Fade R/B

4 3 colors fade 8 Fade G/B

RF signal indicator

RGB on

Mode

hite brightness +

RGB brightness +

Speed +

Zone indicators

SET

RGB off

Farbring

hite on/off

hite brightness ‒

RGB brightness ‒

Speed ‒

Zone selection

(keep pressed for 2 seconds for

all zones

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EuroLite Controller Handbücher

EuroLite

EuroLite TP-330 Bedienungsanleitung

EuroLite

EuroLite FD-512 Bedienungsanleitung

EuroLite

EuroLite SPX-405 DMX Bedienungsanleitung

EuroLite

EuroLite LED CB-12/50 DMX Bedienungsanleitung

EuroLite

EuroLite CB 12/30 Bedienungsanleitung

EuroLite

EuroLite LVH-8 Bedienungsanleitung

EuroLite

EuroLite EASY Show Bedienungsanleitung

EuroLite

EuroLite TP-310 Bedienungsanleitung

EuroLite

EuroLite DMX LED Operator 2 Bedienungsanleitung

EuroLite

EuroLite DMX LED Operator 1 Bedienungsanleitung

EuroLite

EuroLite LED PSU-24V DC Bedienungsanleitung

EuroLite

EuroLite DMX LED OPERATOR 6 Bedienungsanleitung

EuroLite

EuroLite LED C-1 Bedienungsanleitung

EuroLite

EuroLite LED PSU-5A Artnet/DMX Bedienungsanleitung

EuroLite

EuroLite DX-4 Bedienungsanleitung

EuroLite

EuroLite Stage Control 136 Bedienungsanleitung

EuroLite

EuroLite TP-320 Bedienungsanleitung

EuroLite

EuroLite Bigfoot Bedienungsanleitung

EuroLite

EuroLite DMX OPERATOR 1610 Bedienungsanleitung

EuroLite

EuroLite LED PANEL RD Controller DMX Bedienungsanleitung

EuroLite

EuroLite TP-340 Bedienungsanleitung

EuroLite

EuroLite DMX Merger Bedienungsanleitung

EuroLite

EuroLite Ambience Control 4 Bedienungsanleitung

EuroLite

EuroLite DMX Commander 24/48 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch