Evans PRO PE22YR675RH Bedienungsanleitung

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE I

evansproducts.com

REAR WHEEL DRIVE MOWER 22"

CORTACÉSPED 22" CON

TRANSMISIÓN TRASERA

70080682 REV A.

ver. 04/23

OPERATOR’S MANUAL MANUAL DE PROPIETARIO

Please read the operator's manual carefully and make sure you understand the instructions before using the

machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline

exceeding 10% ethanol (E10) will void the product warranty.

Por favor lea cuidadosamente y comprenda estas intrucciones antes de usar esta maquina. Esta máquina puede

utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de

etanol (E10) anulará la garantía del producto.

PE22YR675RH/PE22YR775RH

PRO

Look for this symbol to point out im-

portant safety precautions. It means

CAUTION!!! BECOME ALERT!!! YOUR

SAFETY IS INVOLVED.

WARNING: In order to prevent acciden-

tal starting when setting up, transport-

ing, adjusting or making repairs, always

disconnect spark plug wire and place

wire where it cannot come in contact

with plug.

CAUTION: Muffler and other engine

parts become extremely hot during

operation and remain hot after engine

has stopped. To avoid severe burns on

contact, stay away from these areas.

WARNING: Engine exhaust, some of

its constituents, and certain vehicle

components contain or emit chemi-

cals known to the State of California to

cause cancer and birth defects or other

reproductive harm.

WARNING: Battery posts, terminals and

related accessories contain lead and

lead compounds, chemicals known to

the State of California to cause cancer

and birth defects or other reproductive

harm. Wash hands after handling.

WARNING:This lawnmower isequipped

with an internal combustion engine and

should not be used on or near any

unimproved forest-covered, brush-

covered or grass-covered land un-

less the engine’s exhaust system is

equipped with a spark arrester meeting

applicable local or state laws (if any).

If a spark arrester is used, it should be

maintained in effective working order

by the operator.

In the state of California the above is required by law (Sec-

tion 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. A spark arrester for the muffler is available through

your nearest authorized service center.

I. CHILDREN

WARNING: CHILDREN CAN

BE SERIOUSLY INJURED OR

KILLED BY THIS EQUIPMENT.

Carefully read and follow all of

the safety instructions below.

SAFETY RULES

The American Academy of Pediatrics recommends that

children be a minimum of 12 year of age before operating

a pedestrian controlled lawn mower and a minimum of 16

years of age before operating a riding lawn mower.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and

down for small children.

• Never allow children to operate the machine.

II. GENERAL OPERATION

• Read, understand, and follow all instructions on the

machine and in the manual(s) before starting. Be

thoroughly familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Only allow responsible individuals, who are familiar

with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire,

bones, sticks, etc., which could be picked up and

thrown by blade. Stay behind the handle when the

engine (motor) is running.

• Be sure the area is clear of other people before mow-

ing. Stop machine if anyone enters the area.

• Do not operate machine barefooted or while wearing

sandals. Always wear substantial footwear with good

ankle support while mowing.

• Do not pull mower backwards unless absolutely neces-

sary. Always look down and behind before and while

moving backwards.

• Never direct discharged material toward anyone.

Avoid discharging material against a wall or obstruc-

tion. Material may richochet back toward the operator.

Stop blade when crossing gravel surfaces.

• Do not operate the mower without proper guards,

plates, grass catcher or other safety protective devices

in place.

• See manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks,

or roads.

• Never leave a running machine unattended.

• Stop the engine (motor) and wait until the blade comes

to a complete stop before cleaning the machine, re-

moving the grass catcher, or unclogging the discharge

chute.

• Mow only in daylight or good artificial light.

• Do not operate the machine while under the influence

of alcohol or drugs.

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 1

evansproducts.com

SAFETY RULES ...........................................................1

PRODUCT SPECIFICATIONS ..................................... 3

CUSTOMER RESPONSIBILITIES ............................... 3

ASSEMBLY ................................................................3

OPERATION..............................................................5-9

MAINTENANCE SCHEDULE ..................................... 10

MAINTENANCE .................................................... 10-13

SERVICE AND ADJUSTMENTS ........................... 14-15

STORAGE ............................................................. 15-16

TROUBLESHOOTING........................................... 15-17

TABLE OF CONTENTS

• Never operate machine in wet grass. Always be sure

of your footing: keep a firm hold on the handle; walk,

never run.

• Disengage the drive system, if so equipped, before

starting the engine (motor).

• If the equipment should start to vibrate abnormally,

stop the engine (motor) and check immediately for

the cause. Vibration is generally a warning of trouble.

• Always wear eye protection when operating machine.

• Useextracarewhenapproachingblindcorners,shrubs,

trees, or other objects that may obscure vision.

• Whenloadingorunloadingthismachine,donotexceed

the maximum recommended operation angle of 15°.

• Wear proper Personal Protective Equipment (PPE)

whileoperatingthismachine,including(ataminimum)

sturdyfootwear,eyeprotection,andhearingprotection.

Do not mow in shorts or open toed footwear.

Always let someone know you are outside mowing.

III. SLOPE OPERATION

Slopes are a major factor related to slip & fall accidents,

which can result in severe injury. All slopes require extra

caution. If you feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never up and down.

Exercise extreme caution when changing direction on

slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, bumps or hidden objects. Un-

even terrain could cause a slip and fall accident. Tall

grass can hide obstacles.

DO NOT:

• Do not mow near drop-offs, ditches or embankments.

You could lose your footing or balance.

• Do not mow on wet grass or excessively steep slopes.

Poor footing could cause a slip and fall accident.

IV. SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme

careinhandlinggasoline. Gasolineisextremelyflammable

and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine

running.

• Allow engine to cool before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel container where there

is an open flame, spark or pilot light such as a water

heater or on other appliances.

• Neverfillcontainersinsideavehicle,onatruckortrailer

bed with a plastic liner. Always place containers on

the ground away from your vehicle before filling.

• Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment with a portable container,

rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immedi-

ately.

• Never overfill fuel tank. Replace gas cap and tighten

securely.

V. GENERAL SERVICE

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine

(motor) running. Disconnect the spark plug wire, and

keep the wire away from the plug to prevent accidental

starting.

• Keep all nuts and bolts tight to be sure the equipment

is in safe working condition.

• Never tamper with safety devices. Check their proper

operationregularly. Neverdo anything to interfere with

the intended function of a safety device or reduce the

protection provided by a safety device.

• Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage. Allow machine to

cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Neverattempttomakewheelheightadjustmentswhile

the engine is running.

• Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

components and replace with manufacturer’s recom-

mended parts, when necessary.

• Mowerbladesaresharpand can cut. Wraptheblade(s)

or wear gloves, and use extra caution when servicing

them.

• Do not change the engine governor setting or over-

speed the engine.

• Maintain or replace safety and instruction labels, as

necessary.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

2evansproducts.com

ASSEMBLY

FIG. 1

OPERATOR

PRESENCE

CONTROL

BAR

UPPER

HANDLE

KNOB

LIFT

LOWER

HANDLE

MOWING

POSITION

UPPER

HANDLE

LOWER HANDLE

KNOB

Readtheseinstructionsandthismanualinitsentiretybefore

you attempt to assemble or operate your new lawn mower.

IMPORTANT: THISLAWNMOWERISSHIPPEDWITHOUT

OIL OR GASOLINE IN THE ENGINE.

Your new lawn mower has been assembled at the factory

with the exception of those parts left unassembled for ship-

ping purposes. All parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have been placed in

the parts bag. To ensure safe and proper operation of your

lawn mower, all parts and hardware you assemble must

be tightened securely. Use the correct tools as necessary

to ensure proper tightness.

TO REMOVE LAWN MOWER FROM CARTON

1. Remove loose parts included with mower.

2. Cut down two end corners of carton and lay end panel

down flat.

3. Removeallpackingmaterialsexceptpaddingbetween

upper and lower handle and padding holding operator

presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton thor-

ougly for additional loose parts.

HOW TO SET UP YOUR LAWN MOWER

TO UNFOLD HANDLE (See Figs. 1 and 2)

IMPORTANT: UNFOLDHANDLECAREFULLYSOASNOT

TO PINCH OR DAMAGE CONTROL CABLES.

1. Raise lower handle section to operating position and

align holes in lower handle with holes in handle brack-

ets.

2. Insert handle bolts through lower handles and handle

brackets; secure with lower (“standard”) knobs.

3. Remove protective padding, raise upper handle sec-

tion into place on lower handle and tighten both upper

(“star”) knobs.

4. Removeany packing materialfrom around control bar.

Your handles may be adjusted for your mowing comfort.

Referto“ADJUST HANDLE”intheServiceandAdjustments

section of this manual.

CONGRATULATIONS on your purchase of a new lawn

mower. Ithasbeendesigned,engineeredandmanufactured

togiveyouthebestpossibledependabilityandperformance.

Should you experience any problem you cannot easily

remedy, please contact your nearest authorized service

center/department. We have competent, well-trained

technicians and the proper tools to service or repair this

lawn mower.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your lawn mower

properly. Always observe the “SAFETY RULES”.

SERIAL

NUMBER: _________________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE LAWN

MOWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your lawn mower.

• Follow theinstructionsunder“Maintenance”and“Stor-

age” sections of this owner’s manual.

PRODUCT SPECIFICATIONS

Gasoline Capacity See engine manual

and Type: (Unleaded Regular Only)

Oil Type (API SG–SL): SAE 30 (above 0°C / 32°F) )F°23/C°0woleb(03-W01EAS

Oil Capacity: See engine manual

Spark Plug: NGK BPR5ES (Gap: .030")

Valve Clearance: Intake: 0.006 mm

(± 0.001") Exhaust: 0.008 mm

Blade Bolt Torque: 35–40 ft. lbs.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 3

evansproducts.com

ASSEMBLY

TO ASSEMBLE GRASS CATCHER

(See Fig. 3)

1. Put grass catcher frame into grass bag with rigid part

of bag on the bottom. Make sure the frame handle is

outside of the bag top.

2. Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water

for a few minutes. If bag gets wet, let it dry before using.

TO INSTALL ATTACHMENTS

Your lawn mower was shipped ready to be used as a

mulcher. To convert mower to bagging or discharging,

see “TO CONVERT MOWER” in the Operation section of

this manual.

FIG. 3

FRAME

HANDLE

VINYL

BINDINGS

FRAME

OPENING

FIG. 2

HANDLE

BRACKET

BOLT

KNOB

INSTALL STARTER ROPE (See Fig. 4)

1. Loosen T-knob.

2. Hold control bar against upper handle.

3. Slowly pull engine starter rope out until rope will slip

into loop of rope guide.

4. Tighten T-knob.

FIG. 4

UPPER

HANDLE

CONTROL BAR

ENGINE

STARTER

ROPE

ROPE GUIDE T-KNOB

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

4evansproducts.com

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.

Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjust-

ments. Save this manual for future reference.

MEETS CPSC SAFETY REQUIREMENTS

Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute

and the U.S. Consumer Product Safety Commission. WARNING: The blade turns when the engine is running.

OPERATOR PRESENCE CONTROL BAR – must be

held down to the handle to start the blade. Release to

stop the blade.

DRIVE CONTROL LEVERS – used to engage power-

propelled forward motion lawn mower.

HOUSING

GRASS

CATCHER

STARTER HANDLE – used for starting the engine.

MULCHER DOOR – allows conversion to discharge or

bagging operation.

STARTER

HANDLE

FUEL VALVE LEVER

ENGINE OIL CAP WITH DIPSTICK

HANDLE KNOBS

GASOLINE FILLER CAP

These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand

their meaning.

MULCHER

DOOR

OPERATION

DRIVE CONTROL LEVERS

WHEEL HEIGHT

ADJUSTER LEVER

AIR FILTER

SPARK PLUG

NOTE: Gasoline containing up to 10% ethanol

(E10) is acceptable for use in this machine. The

use of any gasoline exceeding 10% ethanol

(E10) will void the product warranty.

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

MUFFLER

OPERATOR PRESENCE CONTROL BAR

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 5

evansproducts.com

2. Rotate turnbuckle on drive control to increase drive

speed.

3. Operate mower to test drive speed. Readjust as re-

quired.

4. If condition fails to improve after the above steps

(forward speed remains the same), your drive belt is

worn and should be replaced.

OPERATION

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum per-

formance. Speed is not adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require

an engine control to be installed on this

lawn mower in order to minimize the risk

of blade contact injury. Do not under

any circumstances attempt to defeat

the function of the operator control. The

blade turns when the engine is running.

• Your lawn mower is equipped with an operator pres-

ence control bar which requires the operator to be

positioned behind the mower handle to start and

operate the mower.

DRIVE CONTROL (See Fig. 4)

• Self-propelling is controlled by holding the operator

presence control bar down to the handle and pulling

either drive control lever rearward to the handle. The

further toward the handle a lever is pulled, the faster

the unit will travel.

• Forward motion will stop when either the operator pres-

ence control bar or a drive control lever are released. To

stop forward motion without stopping engine, release

a drive control lever only. Hold operator presence

control bar down against handle to continue mowing

without self-propelling.

NOTE: If after releasing the drive control the mower will

not roll backwards, push the mower forward slightly to

disengage drive wheels.

TO ADJUST CUTTING HEIGHT (See Fig. 6)

All four wheels are adjusted by a single lever.

• Pull adjuster lever toward wheel. To raise mower, move

lever forward to desired position. To lower mower, move

the lever toward the rear.

TO ENGAGE

DRIVE CONTROL

DRIVE

CONTROL

LEVERS

DRIVE CONTROL

DISENGAGED

OPERATOR PRESENCE CONTROL BAR

FIG. 4

FIG. 5

ADJUSTMENT TURNBUCKLE

DRIVE CONTROL ADJUSTMENT (See Fig. 5)

Over time, the drive control system may become “loose”,

resulting in decreased speed. There is a turnbuckle on

the drive control housing to increase tension on the drive

cable. Proceed as follows:

1. Turn unit off and disconnect spark plug wire from spark

plug.

FIG. 6

WHEEL

ADJUSTER

LEVER

LEVER BACKWARD

TO LOWER MOWER

LEVER FORWARD

TO RAISE MOWER

The operation of any lawn mower can result in foreign objects thrown into the eyes,

which can result in severe eye damage. Always wear safety glasses or eye shields

while operating your lawn mower or performing any adjustments or repairs. We

recommend standard safety glasses or a wide vision safety mask over spectacles.

Use ear pro-

tectors to

avoid damage

to hearing.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

6evansproducts.com

OPERATION

TO CONVERT MOWER

Your lawn mower was shipped ready to be used as a

mulcher. To convert to bagging or discharging:

REAR BAGGING (See Fig. 7)

• Lift rear door of the lawn mower and place the grass

catcher frame hooks onto the grass bag brackets.

• To convert to mulching or discharging operation,

remove grass catcher and close rear door.

MOWER IS NOW READY FOR

DISCHARGING OPERATION

OPEN MULCHER

DOOR

INSTALL

DISCHARGE

DEFLECTOR

FIG. 8

UNLOCK

LATCH

SIDE DISCHARGING (See Fig. 8)

• Rear door must be closed.

• Open mulcher door and install discharge deflector

under door as shown.

• Mower is now ready for discharging operation.

• To convert to mulching or bagging operation, discharge

deflector must be removed and mulcher door must be

closed and locked.

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear door closed.

2. Mulcher door closed and locked.

FOR REAR BAGGING -

1. Grass catcher installed.

2. Mulcher door closed and locked.

FOR SIDE DISCHARGING -

1. Rear door closed.

2. Discharge deflector installed.

CAUTION: Do not run your lawn mower

without rear door closed or approved

grass catcher in place. Never attempt

to operate the lawn mower with the rear

door removed or propped open.

FIG. 7

GRASS BAG

BRACKET

REAR DOOR

GRASS

CATCHER

HANDLE

GRASS

CATCHER

FRAME HOOK

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 7

evansproducts.com

CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline

near an open flame.

Alcohol blended fuels (called gasohol

or using ethanol or methanol) can at-

tractmoisturewhichleadstoseparation

and formation of acids during storage.

Acidic gas can damage the fuel sys-

tem of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before storage of

30 days or longer. Empty the gas tank,

start the engine and let it run until the

fuellinesandcarburetorareempty. Use

fresh fuel next season. See Storage

Instructions for additional information.

Never use engine or carburetor cleaner

products in the fuel tank or permanent

damage may occur.

OPERATION

BEFORE STARTING ENGINE

ADD OIL (See Fig. 10)

Your lawnmower is shipped without oil in the engine. For

type and grade of oil to use, see “ENGINE” in the Mainte-

nance section of this manual.

CAUTION: DO NOT overfill engine with

oil, or it will smoke on startup.

1. Be sure lawnmower is level.

2. Remove oil fill cap/dipstick from oil fill spout.

3. You recieve a container of oil with the unit. Slowly

pour the entire container down the oil fill spout into

the engine.

4. Insert and tighten oil fill cap/dipstick.

IMPORTANT:

• Check oil level before each use. Add oil if needed.

Fill to full line on dipstick.

• Change the oil after every 25 hours of operation or

each season. You may need to change the oil more

often under dusty, dirty conditions. See “TO CHANGE

ENGINEOIL”intheMaintenance section ofthismanual.

ADD GASOLINE (See Fig. 10)

• Fill fuel tank to bottom of tank filler neck. Do not over-

fill. Use fresh, clean, regular unleaded gasoline with a

minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

FIG. 9

GRASS

CATCHER

FRAME

HANDLE

BAG

HANDLE

TO EMPTY GRASS CATCHER (See Fig. 9)

1. Lift up on grass catcher using the frame handle.

2. Remove grass catcher with clippings from under lawn

mower handle.

3. Empty clippings from bag using both frame handle

and bag handle.

NOTE:Do not drag the bag when emptying; it will cause

unnecessary wear.

TO STOP ENGINE (See Fig. 11)

• To stop engine, release operator presence control bar.

Waituntilbladeand all movingparts have stoppedand

turn fuel valve to OFF position if you do not intend to

restart the engine soon.

TO START ENGINE (See Fig. 11)

NOTE: Due to protective coatings on the engine, a small

amount of smoke may be present during the initial use of

the product and should be considered normal.

1. Be sure fuel valve is in the ON position if eqquiped.

2. Holdoperatorpresencecontrolbar down tothehandle

and pull starter handle quickly. Do not allow starter

rope to snap back.

GASOLINE

FILLER CAP

OIL FILL

CAP/DIP-

STICK

FIG. 10

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

8evansproducts.com

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE

“CLEANING” IN THE MAINTENANCE SECTION OF THIS

MANUAL.

• The special mulching blade will recut the grass clip-

pings many times and reduce them in size so that

as they fall onto the lawn they will disperse into the

grass and not be noticed. Also, the mulched grass

will biodegrade quickly to provide nutrients for the

lawn. Always mulch with your highest engine (blade)

speed as this will provide the best recutting action of

the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends

to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon.

At this time the grass has dried, yet the newly cut area

will not be exposed to direct sunlight.

• For best results, adjust the lawn mower cutting height

so that the lawn mower cuts off only the top one-third

of the grass blades (See Fig. 12). If the lawn is over-

grown it will be necessary to raise the height of cut to

reduce pushing effort and to keep from overloading

the engine and leaving clumps of mulched grass. For

extremely heavy mulching, reduce your width of cut

by overlapping previously cut path and mow slowly.

OPERATION

• Certain types of grass and grass conditions may require

that an area be mulched a second time to completely

hide the clippings. When doing a second cut, mow

across (perpendicular) to the first cut path.

• Change your cutting pattern from week to week. Mow

north to south one week then east to west the next

week. This will help prevent matting and graining of

the lawn.

FIG. 12

MAX 1/3

MOWING TIPS

CAUTION: Do not use de-thatcher blade

attachments on your mower. Such

attachments are hazardous, will dam-

age your mower and could void your

warranty.

• Under certain conditions, such as very tall grass, it

may be necessary to raise the height of cut to reduce

pushing effort and to keep from overloading the engine

and leaving clumps of grass clippings. It may also be

necessary to reduce ground speed and/or run the

lawn mower over the area a second time.

• For extremely heavy cutting, reduce the width of cut

by overlapping previously cut path and mow slowly.

• For better grass bagging and most cutting conditions,

the engine speed should be set in the fast position.

• Pores in cloth grass catchers can become filled with

dirt and dust with use and catchers will collect less

grass. To prevent this, regularly hose catcher off with

water and let dry before using.

• Keep top of engine around starter clear and clean of

grass clippings and chaff. This will help engine air

flow and extend engine life.

FUEL VALVE LEVER

OFF

FIG. 11

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 9

evansproducts.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung