Evertz 7700 Series Bedienungsanleitung

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1

TABLE OF CONTENTS

1. OVERVIEW.......................................................................................................................................... 1

2. INSTALLATION................................................................................................................................... 2

3. SPECIFICATIONS............................................................................................................................... 3

3.1. INPUTS....................................................................................................................................... 3

3.2. OUTPUTS................................................................................................................................... 3

3.3. ELECTRICAL ............................................................................................................................. 3

3.4. PHYSICAL.................................................................................................................................. 3

4. STATUS LEDS.................................................................................................................................... 4

5. CIRCUIT DESCRIPTION..................................................................................................................... 5

6. JUMPERS AND USER ADJUSTMENTS............................................................................................ 6

6.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED

BY THE GLOBAL FRAME STATUS .......................................................................................... 6

6.2. SELECTING THE INPUT AC/DC COUPLING............................................................................ 6

6.3. GAIN ADJUSTMENT.................................................................................................................. 6

6.4. CABLE EQUALIZATION OPERATION...................................................................................... 7

Figures

Figure 1-1: 7700ADA-ETSI Block Diagram...........................................................................................................1

Figure 2-1: Rear Panel.........................................................................................................................................2

Figure 6-1: LED and Jumper Locations ................................................................................................................6

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1

REVISION HISTORY

REVISION DESCRIPTION DATE

1.0 Original Version Nov 06

1.1 General format clean up. Updated Block Diagram. Sept 09

Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for

the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of

Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered

by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.

Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is

granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.

Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,

please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or

specifications.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1 Page - 1

1. OVERVIEW

The 7700ADA-ETSI High Amplitude Distribution Amplifier is a general purpose amplifier with an equalizing

function for distributing a wide range of digital and analog signals. It has been designed to distribute

pulses and signals up to ±3.5V ITU-T G.703 E12 (Physical/electrical characteristics of hierarchical digital

interface at 2048kb/s) signals. The 7700ADA-ETSI features one balanced equalized input with four

outputs.

The 7700ADA-ETSI occupies one card slot and can be housed in a 1RU frame which will hold up to 3

modules, a 3RU frame which will hold up to 15 modules, a 350FR portable frame which will hold up to 7

modules or a standalone enclosure that will hold 1 module.

Features:

•75 Ohm input impedance

•Distribute signals up to ±3.5V to 30MHz

•High common mode range and common mode rejection ratio (CMRR)

•±5.5dB Gain control range

•Jumper selectable AC or DC coupling

•Cable equalizer adjustment range: 0 to 300m of Belden 8281 or 1694A

•Consistent input impedance if card power is lost

Figure 1-1: 7700ADA-ETSI Block Diagram

4 Analog

Outputs

Cabl

Cable

Length

Gain

Impedance

C/DC

Coupling

Balanced

nalog Input

7Ω

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Page - 2 Revision 1.1

2. INSTALLATION

The 7700ADA-ETSI comes with a companion rear panel and occupies one slot in the 7700FR frame.

Figure 2-1 shows a diagram of the rear panel. For information on inserting the module into the frame see

the 7700FR manual section 3.

Figure 2-1: Rear Panel

INPUT: Isolated BNC connector for input signal. The input signal is terminated with 75 ohms. The

INPUT jumper located on the module near the back determines whether the input signal will

be AC or DC coupled. (See section 6.2)

OUT 1 to 4: There are four BNC connectors with equalized and level adjusted copies of the input signal.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1 Page - 3

3. SPECIFICATIONS

All specifications, unless otherwise indicated, are measured under the following conditions:

•1 Vp-p video applied

•75 Ohm source impedance signal

•DC coupled

•Gain adjusted for unity operation into 75 Ohm load

•Cable equalizer set to 0 length

3.1. INPUTS

Standards: Any analog waveform up to ±3.5V and 30MHz bandwidth

Connector: 1 BNC per IEC 61169-8 Annex A

Common Mode Range: >6Vp-p

CMRR: >60dB to 1 kHz

Signal Amplitude: up to ±3.5V

Cable Equalizer: 0 to 300m of Belden 8281 or 1694 cable

Impedance: 75Ohms

Coupling: AC or DC (jumper selectable)

Return Loss: > 40dB to 10MHz, >25dB to 30MHz

3.2. OUTPUTS

Number of Outputs: 4 per card

Connector: 1 BNC per IEC 61169-8 Annex A

Output Impedance: 75 Ohm

Gain Control Range:± 6dB

Freq. Response: < ±0.05dB no equalization (to 5.5MHz)

< ±0.09dB for 5 to 100m Belden 8281 or 1694A (to 5.5 MHz)

< ±0.15dB for 100 to 300m Belden 8281 or 1694A (to 5.5 MHz)

Differential Gain: <0.25 % 0 to 300m (for single load)

Differential Phase: < 0.19 deg 0 to 300m

C/L Gain Inequality: <+/-0.1% for all cable lengths

C/L Delay: <+/-2nsec

Output Isolation: >42dB to 10MHz, >32 dB to 30MHz

Output Return Loss:>40dB to 30MHz

Noise Performance: <-68dB RMS NTC7 weighting,

<-60dB RMS 15 kHz to 5.5MHz

3.3. ELECTRICAL

Voltage: + 12VDC

Power: 2.5 Watts

3.4. PHYSICAL

Number of Slots: 1

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Page - 4 Revision 1.1

4. STATUS LEDS

Two large LEDs on the front of the board indicate the general health of the module.

LOCAL FAULT: This Red LED indicates poor module health and will be illuminated when a local

input power fault exists (i.e.: a blown fuse). The LOCAL FAULT indication can also

be reported to the frame through the FRAME STATUS jumper.

MODULE OK: This Green LED indicates good module health. It will be On when the board power

is good.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1 Page - 5

5. CIRCUIT DESCRIPTION

The input signal enters the board through a BNC with isolated ground so that balanced input processing

may be done to remove any common mode hum that may have been added to the signal and ground

shield. The input coupling (AC/DC) can be selected using an on-board jumper (J4).

An adjustable gain stage feeds the cable equalizer that can adjust the frequency response to match the

attenuation of up to 300m of coaxial cable. One OP-Amp drives the four output BNC's with 75-Ohm output

impedance.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Page - 6 Revision 1.1

6. JUMPERS AND USER ADJUSTMENTS

MODULE STATUS

J6 16948281 CABLE

INPUT

(1)7700ADA-ETSI

J1 FRAME STATUS

OFF

GAIN

EQ CTRL

Figure 6-1: LED and Jumper Locations

6.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED

BY THE GLOBAL FRAME STATUS

The FRAME STATUS jumper J1, located at the front of the module, determines whether local faults (as

shown by the Local Fault indicator) will be connected to the 7700FR frame's global status bus.

FRAME STATUS: To monitor faults on this module with the frame status indicators (on the power

supply’s FRAME STATUS LEDs and on the Frame's Fault Tally output) install this

jumper in the On position.

When this jumper is installed in the Off position local faults on this module will not

be monitored.

6.2. SELECTING THE INPUT AC/DC COUPLING

The input may be AC or DC (default) coupled into the input-circuitry using jumper J4. In some non-video

applications that do not have DC information (i.e. digital AES audio), AC coupling can be used to remove

any DC level that may have built up in its transmission.

6.3. GAIN ADJUSTMENT

The GAIN POT on the cards front edge allows you to adjust the input signal level. Turning the POT

clockwise will increase the gain.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Revision 1.1 Page - 7

6.4. CABLE EQUALIZATION OPERATION

With the cable equalizer EQCTRL POT set fully counter-clockwise, the cable equalizer will be set to the

"zero length". As you turn the POT clockwise, more cable equalization is added. To set the POT to the

correct position, perform the following calibration:

1. Supply the cable being equalized with a frequency response test signal.

2. Make sure the driving level from the test generator is calibrated to unity.

3. Set the cable type jumper (J6) to the type of cable you are using (either 8281 or 1694). If you are using

a different type, then use either setting.

4. Make sure the test gear is terminated properly.

5. Calibrate the GAIN level POT for unity output at low frequencies.

6. Adjust the "EQCTRL" POT until the 7700ADA-ETSI output signal has flat frequency response.

7700 Multiframe Manual

7700ADA-ETSI High Amplitude Distribution Amplifier

Page - 8 Revision 1.1

This page left intentionally blank

Andere Handbücher für 7700 Series

127

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere evertz Verstärker Handbücher

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700 MultiFrame Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700ADA7-EQ MultiFrame Bedienungsanleitung

evertz

evertz 7700ADA-EQ Bedienungsanleitung

evertz

evertz 500DA Bedienungsanleitung

evertz

evertz 7700DA-HD Bedienungsanleitung

evertz

evertz exponent 500ADA-EQ Bedienungsanleitung

evertz

evertz 7815VPDA Series Bedienungsanleitung

evertz

evertz 500DA2Q-AESU Bedienungsanleitung

evertz

evertz exponent 500IDA9-IG Series Bedienungsanleitung

evertz

evertz 7700ADA6-EQ-L Bedienungsanleitung

evertz

evertz 7700DA7-HD Bedienungsanleitung

evertz

evertz exponent 520DARS-W Bedienungsanleitung

evertz

evertz exponent 500ADA-AUD Bedienungsanleitung

evertz

evertz 7710DCDA-HD Bedienungsanleitung

evertz

evertz 7800DA8-12G Bedienungsanleitung

evertz

evertz 7700DA6-L Bedienungsanleitung

evertz

evertz exponent 500ADA-W Bedienungsanleitung

evertz

evertz 500DA2Q-3G Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz exponent 500ADA Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung