Evikon PluraSens E2648-N2O Bedienungsanleitung

PluraSens®

Nitrous Oxide Detector-Transmitter

E2648-N2O

User Manual

E2648-N2O Rev 10.05.2023

Table of contents

Nitrous Oxide 3

Speciﬁcations 4

Product description 6

Safety requirements 6

Operating conditions 7

Installation guidelines 7

Mounting dimensions 8

Sensor probe handling 9

Gas sensor replacement procedures 9

Electrical connections 10

Correct and incorrect cabling for 24 VAC 12

Operation 13

Maintenance 13

Calibration 13

Delivery set 14

Order code for E2648-N2O options 14

Conﬁguring 15

Return to default settings 15

Modbus RTU Communication 16

RS485 communication interface 16

Communication parameters 16

Modbus holding registers 16

Warranty 21

Manufacturer contacts 21

E2648-N2O Rev 10.05.2023

Nitrous Oxide

Nitrous oxide is a colorless non-ﬂammable gas, with a slight metallic scent and taste. It is

also known as laughing gas or nitrous.

Chemical formula

N2O

Molar weight

Relative gas density (to air)

1.53

Conversion

1 ppm= 1.8 mg/m3

Boiling point

-88.48 °C

Odor

Slightly sweetish

Hazards

Will support combustion, and may increase the intensity

of the ﬁre. Containers may explode when heated.

Inhalation causes intense analgesia; concentrations of

over 40-60% cause loss of consciousness preceded by

hysteria. Contact of liquid with eyes or skin causes

frostbite burn.

Exposure

limits (ACGIH)

TWA

25 ppm

Conversion of ppm to mg/m3is calculated for 25°C and 1 atm.

E2648-N2O Rev 10.05.2023

Speciﬁcations

Sensor type

Optical (NDIR)

Sampling method

Diffusion

Typical detection range

0...1000 ppm

Max. overload

2000 ppm

Resolution

1 ppm

Response time T90

< 30s

Sensor lifetime

> 5 years

Calibration interval

12 months

Signal update

Every 1 second

Power supply

12...36 VDC (default),

24 VAC or 230 VAC as options

Power consumption

< 2 VA

Load resistance

RL< (Us - 2 V) / 22 mA for 4-20 mA

RL> 250 kOhm for 0-10 V mode

Digital interface

RS485, Modbus RTU protocol

Analog outputs

2 × 4-20 mA / 0-10 V, user settable

Outputs assignment

OUT1 gas; OUT2 gas

Output scale width

> 10 × resolution

Recommended: 20-100% of the detection range

Enclosure

Die-cast aluminum, wall mount, protection class IP66

Dimensions

H120 × W125 × D57 mm

CE marking

According to 2014/30/EU and 2014/35/EU, EN 50491-4-1:2012

EN 61000-6-3:2020, EN 61326-1:2013(EMC, emissions)

EN 61000-6-1:2019, EN 61000-6-2:2019(EMC, Immunity)

EN 60079-29-1:2016, EN 60079-29-2:2015 and EN 60079-29-3:2014

Operating conditions

-20 °C to +50 °C

0 to 95% RH non-condensing;

0,9...1,1 atm;

Explosion safe areas

Non-aggressive atmosphere

NOTE: The sensor has cross-sensitivity to CO2, ask from manufacturer

details

E2648-N2O Rev 10.05.2023

Relay option

Relay outputs

2 × SPST, max 5 A, 30 VDC / 250 VAC

Default alarm setpoints

(set/release)

RE1 (LOW): 50/40 ppm

RE2 (HIGH): 100/80 ppm

deﬁned by user

within 5-95% of the detection range

Other options

Remote probe

protection IP65, default cable length 3.0 m;

max-height 80 mm, max diameter 65 mm

E2648-N2O Rev 10.05.2023

Product description

E2648 series heavy duty detectors-transmitters belong to the PluraSens® family of

multifunctional measurement instruments. The instruments utilize gas sensors of various

types with excellent repeatability, stability, and long lifetime. Due to its IP66 enclosure of

die-cast aluminum, the device may be used under harsh conditions.

The E2648 series provides two independent analog outputs OUT1 and OUT2,

user-selectable to 4-20 mA or 0-10 V, proportional to gas concentrations. RS485 Modbus

RTU digital communication interface allows easy instrument conﬁguration and integration

into various automation systems.

The following features are available as an option:

●Two relays RE1 and RE2 with closing contacts. Relay outputs can be used to

switch alarm sirens, ventilation fans, shut-off valves, or other actuators,

●24 VAC or 230 VAC as options for power supply module,

●Remote probe.

The version of your detector is marked on the package. If the symbol

⚠

is marked on the

equipment, consult the documentation for further information.

Safety requirements

Misuse will impair the protection of the product. Always adhere to the safety provisions

applicable in the country of use.

Do not perform any maintenance operation with the power on. Do not let water or foreign

objects inside the device.

Removal of the PCB from the enclosure voids the warranty. Do not touch the electronic

components directly, as they are sensitive to static electricity.

Connection diagrams can be found in the electrical connections section. The device might

not perform correctly or be damaged if the wrong power supply is connected.

External circuits connected to the equipment should have suﬃcient insulation rating

according to the environmental conditions and equipment power.

A disconnecting device that is marked as such and easily accessible should be included in

the installation of this product.

E2648-N2O Rev 10.05.2023

Operating conditions

The device should be used both in non-hazardous areas and in a basic electromagnetic

environment, where the latter is deﬁned in EN 61326-1. Avoid strong mechanical shock and

vibrations. Avoid corrosive atmosphere and areas highly contaminated with dust, oil mist,

etc. Keep the instrument away from direct sunlight. A sudden temperature or humidity

change might affect the sensitivity of the sensor.

Installation guidelines

Before proceeding with the installation it is mandatory to read the Safety requirements

section and make sure to comply with all listed instructions. Installation standards EN

60079-29-2 and EN 45544-4 are also recommended for further instructions and related

information about the installation. During the installation of the transmitter the following

points must be considered:

●Application (the instrument is intended for leakage control.)

●Properties of the space under investigation (room geometry, direction, and

velocity of airﬂows, etc.),

●Nitrous oxide is heavier than air. The recommended location is close to or below

the potential leakage source.

●The device should be accessible for maintenance and repair.

The aforementioned conditions above will affect the coverage area of the device. However,

the coverage area for a transmitter is usually between 2.5 to 5 meters radius.

For early leakage detection, install the sensor as close as possible to the potential leakage

sources (ﬂanges, valves, pressure reducers, pumps, etc.), taking into consideration other

points listed above.

Do not locate the detector close to ventilation openings and strong air currents. Avoid the

areas without air circulation (corners, niches) as well.

For general area monitoring without deﬁnite leakage sources, the detectors should be

distributed evenly in the room.

For personal safety control, the detectors are installed in the breathing zone (at the height

of the head of people or animals). The recommended sensor position is vertical, pointing

downwards.

Unscrew four lid screws and detach the lid from the transmitter. Attach the device to a wall

with screws passing through mounting holes. The device is ﬁxed on the wall using two

holes located outside the sealed area of the device.

E2648-N2O Rev 10.05.2023

Mounting dimensions

Front view

Bottom view

E2648-N2O Rev 10.05.2023

Sensor probe handling

The E2648 series devices are available with a remote probe. The remote probe is

connected to the main unit with a shielded cable. The default remote probe cable length is

3 m.

A) Wall mount remote probe with ﬁxing clamp (default version),

B) Remote probe with rubber ﬂange and three self-tapping screws (on request)

The sensor probes of all types are equipped with a hydrophobic microporous PTFE ﬁlter to

protect the sensor from dust, dirt, and water drops. The ﬁlter should be replaced if it gets

strongly contaminated. To replace the PTFE ﬁlter, unscrew the sensor head cap and

remove the old ﬁlter. Place a new ﬁlter into the cap and tighten it again.

NOTE! Never stab or press the ﬁlter near its center where the sensor is located since this

may damage the sensor. Do not remove the ﬁlter as it may cause the device to show

incorrect values and/or break the sensor.

The recommended orientation of the sensor probe is vertical with the sensor tip pointing

downwards. This prevents the possible accumulation of condensed water on the sensor

protection ﬁlter.

Gas sensor replacement procedures

1. Remove the sensor head cap from the device (or the remote probe),

2. Remove the PTFE ﬁlter (if it is not removed within the cap),

3. Remove the O-ring rubber,

4. Detach the NDIR sensor from the device,

5. Insert the new NDIR sensor inside,

6. Put back the O-ring rubber, PTFE ﬁlter, and the head cap, respectively.

E2648-N2O Rev 10.05.2023

Electrical connections

Unscrew four lid screws and detach the lid from the device. Use the M16 cable gland to let

in cables of the power supply and of the external devices. Attach the power cable to the

device without turning it on. Using the connection diagram below, connect the analog

outputs and digital interface terminals to the relevant devices according to your tasks.

Version with PSU and relays Version with PSU and without relays

Version without PSU and with relays Version without PSU and relays

Inhaltsverzeichnis

Andere Evikon Sender Handbücher

Evikon

Evikon PluraSens E2608-CO2 Bedienungsanleitung

Evikon

Evikon PluraSens E2648-HFC Bedienungsanleitung

Evikon

Evikon PluraSens E2648-NO2 Bedienungsanleitung

Evikon

Evikon E2660-CO-CO2 Bedienungsanleitung

Evikon

Evikon PluraSens E2611-NH3 Bedienungsanleitung

Evikon

Evikon PluraSens E2227 Bedienungsanleitung

Evikon

Evikon PluraSens E2648-NH3-E Bedienungsanleitung

Evikon

Evikon PluraSens E2608-N2O Bedienungsanleitung

Evikon

Evikon PluraSens E2658-O3 Bedienungsanleitung

Evikon

Evikon PluraSens E2638-HFC Bedienungsanleitung

Evikon

Evikon PluraSens E2608-NO Bedienungsanleitung

Evikon

Evikon E2618-H2 Bedienungsanleitung

Evikon

Evikon PluraSens E2658-ETO Bedienungsanleitung

Evikon

Evikon PluraSens E2618-LEL Bedienungsanleitung

Evikon

Evikon PluraSens E2658-NH3-S Bedienungsanleitung

Evikon

Evikon PluraSens E2618-O3 Bedienungsanleitung

Evikon

Evikon PluraSens E2670-PID Bedienungsanleitung

Evikon

Evikon E2608-CH4 Bedienungsanleitung

Evikon

Evikon PluraSens E2608-Cl2 Bedienungsanleitung

Evikon

Evikon E2638-H2S Bedienungsanleitung

Evikon

Evikon E2618-NH3 Bedienungsanleitung

Evikon

Evikon E2615-LEL Bedienungsanleitung

Evikon

Evikon E2660-CO-CO2 Bedienungsanleitung

Evikon

Evikon PluraSens E2618 Series Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung