Extech Instruments BR200-2 Bedienungsanleitung

User Guide

Video Borescope

Models BR200 and BR250

BR200-BR250-EU-EN v7.4 2/14

Introduction

Congratulations on your purchase of this Extech BR200 (17mm camera head) or BR250 (9mm

camera head) Video Borescope. This instrument was designed for use as a remote inspection

device. It can be used to peer into tight spots and then supply real-time video and images that can

be recorded. Typical applications include HVAC inspection, automotive inspection, cable routing,

and automotive/boat/aircraft inspection. This meter is shipped fully tested and, with proper use, will

provide years of reliable service.

Features

3.5 '' TFT-LCD palm LCD monitor with high resolution

The image head and the cable are water resistant when the unit is fully assembled (the

monitor and the camera are not water resistant)

Wireless and hard-wired functionality

The monitor records video and images

Micro SD card memory (16G max. size); Please use Class 6 (or higher) TF Flash memory card

Safety

Do not expose instrument to moisture

Shut off the instrument when not in use

Remove the batteries when cleaning the instrument

Replace all batteries at the same time

Supplied Equipment

1. Camera

2. LCD Monitor

3. Monitor Adaptor

4. Adaptor cable

5. Accessory Magnet / Hook / Mirror

6. Magnetic mount

7. Flex cable and camera head

8. 4 AA Batteries

Note: Micro SD card and adaptor (not shown)

456

12 3

BR200-BR250-EU-EN v7.4 2/14

Description

1 Signal output

2 Power Indicator

3 Power On/Off, Dimmer

4 Flexible tube

5 Camera head and LED’s

6 OK

7 Up arrow, video or jpg

8 Menu

9 Down arrow

10 Power On/Off

11 Power Indicator

12 USB Socket

13 Video output

14 SD card socket

15 Power supply socket

16 Reset

17 Signal input

BR200-BR250-EU-EN v7.4 2/14

Installation

Install the batteries into the instrument body, charge the monitor battery, connect the camera and

flexible tube to the body, and insert the micro SD card. Install any accessory as needed.

Battery Installation

Connect Monitor Power

The monitor has a rechargeable battery. Plug in the AC adaptor and connect the cable to the

DC5V socket on the monitor. The power indicator will light in red (or the battery capacity icon on

LCD of monitor will blink, indicating that it is charging - and will turn off after a full charge)

Connect the camera and flexible tube

Connect the camera tube to the instrument body; ensure that the keyed ends are properly aligned.

Once aligned, tighten the knurled knob to hold the connection firmly in place.

Warning. Permanent damage to the flex tube and loss of operation will occur if the flex

tube is subjected to narrow radius or sharp angle bends.

Inserting the micro SD card

Insert card with arrow pointing toward slot. Gently apply pressure until card locks into the spring

loaded slot. To remove from unit, gently push the card inward and then release to eject it from the

card slot. Please use Class 6 (or higher) TF Flash memory card.

BR200-BR250-EU-EN v7.4 2/14

Installing the accessory tools （BR200）

The included accessories (mirror, hook and magnet) all attach to the camera in the same manner.

Refer to the diagrams below:

Installing the accessory tools （BR250）

Hook the attachment into the hole in the head and then slide the rubber sleeve over the

attachment shaft

Attaching the Monitor to the instrument body

Connect the USB Cable

Use the USB cable to connect the monitor to a PC. The USB online icon will appear on the

PC. Open My Computer on the PC, and locate the Mobile Disk. The Mobile disk can be

used and accessed in the same manner as any external hard drive.

Video Output

Insert the video cable into the VIDEO OUT socket on the monitor. Insert the other end of the

cable into the VIDEO IN jack of a TV or other monitor. The LCD Monitor will output a high

quality video image.

Installing the Magnetic bracket

The magnetic bracket slides onto the rear of the monitor for convenient placement and

viewing.

BR200-BR250-EU-EN v7.4 2/14

1.0x

1:00:00 6

Operation

Basic Operation

1. Turn the ON/OFF dial switch to power the camera. The power indicator will switch on. The

switch then acts as a dimmer for the two LEDs on the imager head of the camera.

2. Press and hold the monitor power switch for at least 2 seconds and the power indicator will

illuminate green and a Welcome screen will appear.

3. The real time image will then appear on the display LCD monitor.

Note. If the picture does not properly syncronize or has poor color, check that the Video

System Settings are set to “NTSC”, not to ‘PAL” . This should fix the condition..

4. Use the up arrow to select video or photo mode.

5. Turn the ON/OFF dial to adjust the LED light intensity as desired.

6. The tube can be easily maneuvered into position. The tube can be bent into the shape of the

area to be examined.

7. Use the supplied accessories to help retrieve small items.

LCD Reset

If the BR200/BR250 LCD Monitor will not power ON, or if it powers OFF during use, follow the steps

below to perform a Power Reset:

1. Un-dock the LCD module from the BR200/BR250 pistol-grip base unit.

2. Connect the AC adapter to the LCD module and to the appropriate AC power source.

3. Locate the Power Reset port on the reverse side of the LCD module (labeled Reset).

4. Using a non-metallic object, momentarily press the Power Reset button for a period of 2-to-5

seconds and then release.

5. Leaving the AC adapter connected to the LCD module, attempt to power the unit ON.

6. If the unit powers ON, allow it to fully re-charge (up to 2 hours) before removing the AC

adapter. If the LCD unit does not power ON, repeat steps 1 through 6.

If, after two attempts to reset the LCD, the unit still does not power ON, contact Technical Support.

Taking a Picture

In Photo mode, press OK to take a picture. The photo will automatically save to the SD

card.

Recording a Video

In Real-Time Monitoring (video) mode, press OK to begin recording; refer to the following diagram

for display icon definitions:

1. Battery capacity

2. Function icon (video/photo)

3. Recording in progress

4. ZOOM level

5. Current Date and Time

6. REC Time remaining

7. SD card

BR200-BR250-EU-EN v7.4 2/14

Viewing a Photo or Video

1. In the Real-Time Monitoring mode, press to display a list of

dated playback folders

2. Use the ▼▲keys to select the desired folder.

3. Press OK to open the selected folder and view a list of photo or

video files.

4. Files are listed by time followed by (VID”) for photos or (VID) for

videos

5. Use the ▼▲keys to select a file.

6. Press OK to display the selected photo or video.

For video files:

Press OK to pause while playing.

Press again to resume.

▲Fast Forwards the video

▼Rewinds the video

Press to stop video

7. Press to return to menu.

8. Press again to exit.

Note: Video automatically saves to file every 30 minutes. When the SD card is filled to capacity, the SD

card icon changes to ‘F’. No video will be recorded if the SD card is not inserted in the slot.

Delete a Single Video Or Photo

1. In the Real-Time Monitoring mode, press to display a list of dated

playback folders

2. Use the ▼▲keys to select the desired folder.

3. Press OK to open the selected folder and view a list of photo or

video files.

4. Files are listed by time followed by (VID”) for photos or (VID) for

videos

5. Use the ▼▲keys to select a file.

6. Press and HOLD the button, the display will show ‘DELETE

CURRENT FILE?’

7. Use the arrow keys to select YES or NO

8. Press OK to accept selection.

9. Press twice to exit the Delete screen.

Delete a File Folder

To delete a folder, use the same instructions for deleting a single video or photo. The only additional

concern is that if a folder is not empty it cannot be deleted. Delete all of the files in a folder before

deleting the folder. If the user attempts to delete a folder that is not empty, the following message will

appear: FOLDER NOT EMPTY

Video Display on a PC

Several methods are available to playback or to copy video files on a PC. When connected, the files will

become available as new drives on the PC.

1. SD card adaptor: Insert the SD card into the SD adaptor and then insert the adaptor into the PC

SD slot (if available)

2. USB adaptor: Insert the SD card into a USB adaptor and plug into a USB port.

3. USB cable. Connect the USB cable from the camera to the PC.

13:00:24 VID”

2009-06-10 0001/0004

13:00:24 VID”

13:00:24 VID

13:00:24 VID”

2009-06-10 0001/0004

13:00:24 VID”

13:00:24 VID

BR200-BR250-EU-EN v7.4 2/14

Settings Mode

Press and hold for two seconds to enter the Settings Mode.

Language Settings

1. In Settings Mode, use the arrow keys to select SYSTEM SETTING (green icon).

2. Press OK to call up the SYSTEM icon list

3. Use the arrow keys to highlight the Language icon (globe)

4. Press OK and the Language icon list will appear (flags)

5. Use the arrow keys to highlight the desired language

6. Press OK to select the highlighted language and exit

Video System Settings

1. In Settings Mode, use the arrow keys to select SYSTEM SETTING (green icon).

2. Press OK to call up the SYSTEM icon list

3. Use the arrow keys to highlight the Video System icon (yellow)

4. Press OK and the Video format selections will appear (NTSC, PAL)

5. Use the arrow keys to highlight NTSC

6. Press OK to select the highlighted format and exit

Format and Erase Media

1. In Settings Mode, use the arrow keys to select SYSTEM SETTING (green icon).

2. Press OK to call up the SYSTEM icon list

3. Use the arrow keys to highlight the FORMAT icon (blue)

4. Press OK and the FORMAT selection screen will appear (YES, NO)

5. Use the arrow keys to highlight the desired response

6. Press OK to accept the selection and exit

Restoring Factory Default Settings

1. In Settings Mode, use the arrow keys to select SYSTEM SETTING (green icon).

2. Press OK to call up the SYSTEM icon list

3. Use the arrow keys to highlight the DEFAULT icon (red)

4. Press OK and the DEFAULT selection screen will appear (YES, NO)

5. Use the arrow keys to highlight the desired response

6. Press OK to accept the selection and exit

View Version

1. In Settings Mode, use the arrow keys to select SYSTEM SETTING (green icon).

2. Press OK to call up the SYSTEM icon list

3. Use the arrow keys to highlight the VERSION icon (green)

4. Press OK to view the version

5. Press OK again to exit

Frame Rate Setting

1. In Settings Mode, use the arrow keys to select RECORDER SETTING (red icon).

2. Press OK to call up the RECORDER options

3. Use the arrow keys to highlight the FPS (frames per second) icon

4. Press OK to open the FPS parameter

5. Use the arrows to select the frame rate: 10, 15, 20, 25, or 30

6. Press OK to confirm

BR200-BR250-EU-EN v7.4 2/14

Time Stamp ON OFF Setting

1. In Settings Mode, use the arrow keys to select RECORDER SETTING (red icon).

2. Press OK to call up the RECORDER options

3. Use the arrow keys to highlight the Time Stamp icon (purple)

4. Press OK to open the parameter

5. Use the arrows to select ON or OFF

6. Press OK to confirm

Date/Time Setting

1. In Settings Mode, use the arrow keys to select DATE-TIME SETTING (yellow icon).

2. Press OK to call up Date and Time Settings window

3. Use OK to tab through the fields

4. Use the arrow keys to change a field setting

5. Press the button to exit

Battery Replacement

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries

/ accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

BR200-BR250-EU-EN v7.4 2/14

Specifications

CAMERA

Imaging Sensor CMOS

Total Pixels (NTSC) BR200: 712 x 486; BR250: 640 x 480

Horizontal View Angle BR200: 50 degrees

BR250: 45 degrees

Transmission Frequency 2468MHz

Focus point BR200: 20cm (8”), BR250: 10cm (4”)

Minimum Illumination 0 Lux

Modulation Type FM

Bandwidth 18MHz

Power Supply 4 x AA batteries

Unobstructed Effective Range 10m

Waterproof Capacity IP67 (imager head only)

Dimensions (W D H) 186 x 145 x 41(mm) (Exclude Flexible Tube)

Weight (approx) BR200: 530g

BR250: 450g

Camera head Diameter BR200: 17mm (0.67”)

BR250: 9mm (0.36”)

Operating Temperature -10°C~+50°C

+14°F~+122°F

MONITOR

LCD Screen Type 3.5” TFT-LCD

Effective Pixels 320 (R.G.B.) x 240

Video System PAL/NTSC

Transmission Frequency 2468MHz (CH 4)

Exterior Supply Voltage 5VDC

Consumption Current (Max.) 500mA

Charge Time 3 hours

Work Time 2 hours

Video Output Level 0.9-1.3VP-P@75Ώ

Receiving Sensitivity ≤-85dBm

Dimensions (W x D x H) 100 x 70 x 25(mm)

Weight (Approx) 140g

Operating Temperature -10°C~+50°C

+14°F~+122°F

Operating Humidity (Max.) 15~85%RH

FCC Information

This device complies with part 15 of the FCC rules.

BR250/200: FCC-ID TW5GB8802-GB8803

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference that may cause

undesired operation.

Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extech Instruments Diagnosegeräte Handbücher

Extech Instruments

Extech Instruments BR90 Bedienungsanleitung

Beliebte Diagnosegeräte Handbücher anderer Marken

Mindray

Mindray M7Vet Kurzanleitung

Autel

Autel MaxiProgrammer 201 Bedienungsanleitung

TEXA

TEXA TMD2 Bedienungsanleitung

Autel

Autel MaxiIM IM608 Bedienungsanleitung

Sealey

Sealey BT2012 Bedienungsanleitung

Diagnoptics

Diagnoptics Age Reader Bedienungsanleitung

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Bedienungsanleitung

Hella Gutmann

Hella Gutmann Mega macs X Bedienungsanleitung

Foxwell

Foxwell I80TS Bedienungsanleitung

KaVo

KaVo 3D eXam Bedienungsanleitung

ATEQ

ATEQ VT46 Bedienungsanleitung

Hella Gutmann

Hella Gutmann mega macs X Bedienungsanleitung

Autel

Autel MaxiFlash VCMI Bedienungsanleitung

Qiagen

Qiagen QIAcube Connect MDx Bedienungsanleitung

Alber

Alber BDSU Bedienungsanleitung

St. Jude Medical

St. Jude Medical QUANTIEN Bedienungsanleitung

Bosch

Bosch DCU 100 Bedienungsanleitung

Launch

Launch CNC-602A Bedienungsanleitung