Extech Instruments EA15 Bedienungsanleitung

User's Guide

Thermocouple Datalogging Thermometer

Seven (7) Thermocouple input types K, J, T, E, R, S, N

Dual thermocouple Input with PC Interface

Model EA15

EA15-EU-EN-V3.1 04/12

Introduction

Congratulations on your purchase of the Extech Datalogging Thermometer. The EA15 offers dual

thermocouple inputs with manual and automatic datalogging capabilities. The EA15 includes a PC

interface and WindowsTM compatible software for real-time monitoring and storage of temperature

data. This meter is shipped fully tested and calibrated and, with proper use, will provide years of

reliable service.

Meter Description

1. RS-232 and thermocouple input jacks

2. LCD display

3. Power, Data Hold, and Backlight buttons

4. MAX/MIN, display select, and units buttons

5. MEM, input TYPE, and READ buttons

6. SET button

7. Battery compartment (rear)

8. Up/Down scroll button

9. Enter Button

EA15-EU-EN-V3.1 04/12

Operation

Connecting thermocouples

1. This meter accepts two thermocouples with spade plugs (sub-miniature type with one spade

wider than the other).

2. Plug the thermocouple(s) into the meter's T1 and/or T2 thermocouple input jack(s).

3. Always check the LCD display for the proper thermocouple type selection.

Turn Power ON

Press the button to turn power on. The meter will perform a short self-test. When a

thermocouple is not plugged into the selected input, or if a thermocouple is "open", the display will

show "- - - - -". The default thermocouple type, units and display configuration are determined from

the parameters selected when the meter was last used.

Selecting thermocouple type

Press the TYPE button to select the type of thermocouple.

Selecting °C, °F or °K units of measure

Press the C/F/K button to select the unit of measure.

Selecting T1, T2, and T1-T2 Displays

Press the T1 T2 T1-T2 button to step through and select from the following displays:

a. T1 (thermocouple 1) is the primary display; T2 (thermocouple 2) is the lower display

b. T2 is the primary display and T1 is the lower display

c. T1-T2 (difference between T1 and T2) is the primary display and T1 the lower display

d. T1-T2 is the primary display and T2 is the lower display

Notes:

To avoid electrical shock or personal injury, do not apply more than 20Vrms, between the

thermocouples, or between any thermocouple and earth ground.

If voltage on the measurement surface results in potentials of more than 1V, measurement errors

may occur.

If a potential exists between the thermocouples, use electrically insulated thermocouples.

Data Hold

Press the HOLD button to freeze the displayed reading. The 'H' HOLD icon will appear on the

display. Press the HOLD button again to return to normal operation.

MIN, MAX, AVG Recording Function and Timer

Press the MX/MN button to begin capturing the Minimum (MN), Maximum

(MX), and Average (AVG) temperature values. The Elapsed Time clock

will appear on the lower left of the display. The primary display shows the

current temperature. The lower display will indicate the MX, MN or AVG

value (depending on which is selected) captured since the MX/MN button

was pressed.

1. Press the MX/MN button to step through the MX, MN or AVG display Each reading will be

accompanied by a Timer value indicating the time the reading was recorded

2. Press and hold the ‘’ button to change the elapsed time format from min:sec to hour:min

3. Press and Hold the MX/MN button to exit the MX/MN function.

Backlight

Press the backlight button to switch on the LCD display backlight. The backlight will

automatically switch off after one minute (press button again to turn the light off manually).

EA15-EU-EN-V3.1 04/12

Auto Power OFF

The meter will automatically switch off after 30 minutes of inactivity. AUTO POWER OFF is disabled

in the MAX/MIN and Datalogging modes.

To disable AUTO POWER OFF manually:

1. Hold the enter button ‘’ while turning power on.

2. The AUTO POWER OFF function will be reactivated when the meter is manually turned off.

Turning Power OFF

Press the button to turn power off.

Manual Datalogging

Manual datalogging allows the user to store and recall up to 98 temperature readings.

1. Press the MEM button to manually store a single reading into

memory. The ‘MEM’ icon and location number of the reading will

appear on display for two seconds and then the normal display will

return.

2. To view stored readings, press the READ button. The memory

location number will briefly appear and then the ‘READ’ icon and the

stored values will appear on the display

3. Use the up/down buttons to scroll through the memory locations and view the logged readings.

4. Press the ‘READ’ button to exit the read mode

5. Press and hold the MEM button while turning the meter on to clear

the memory. When the LCD indicates "CLr", the memory has been

cleared.

Automatic Datalogging

Automatic datalogging allows the user to store up to 8,800 temperature readings in memory for later

downloading and viewing using the supplied software. The storage interval rate is programmable

from 3 to 255 seconds.

1. Press and HOLD the SET button for two seconds to enter the

interval programming screen. The ‘MEM’ and ‘INTERVAL’ icons

and interval time will appear on the display. Use the up/down

buttons to scroll through the available intervals (3 to 255

seconds). Press the ‘’ button to select the desired logging

interval

2. Make note of the start time (time of day) for the datalogging

session as this information will be useful when downloading the

data.

3. Press and hold the MEM button for two seconds to enter the datalogging mode. The ‘MEM’ icon

on the center of the display will flash each time a record is stored (at the interval selected).

When the memory is full, ‘FULL’ will appear on the display and the meter will stop logging data.

4. To stop and exit the datalogging mode, press the MEM button.

5. To download data, read the datalogging sections below.

Note: MAX/MIN/AVG functions can be used with the meter in datalogging mode

Clearing stored data

1. Press the “ ” button to turn the meter off.

2. Press and hold the MEM button, then press the “ ” button to turn the meter on. When the

LCD indicates "CLr", the entire memory has been erased.

EA15-EU-EN-V3.1 04/12

Datalogging Software

The instructions on how to install the datalogging software are printed on the Software CD label.

After reading the label’s directions, load the software CD in the PC CD-ROM drive.

When the program is opened a COM PORT selection prompt appears. Select the PC COM PORT

that will be used to connect the meter to the PC with the supplied cable (the cable connects to the

top of the meter and to the USB COM PORT on the PC).

Once the COM PORT selection is correctly made, the meter and PC begin communicating. The

main software screen, shown at right, appears. The menu icons at the top of the screen are

explained below.

FILE ‘SAVE AS’ ICON

The SAVE FILE icon is the first icon on the left. Click on this icon to save recorded data to a text file.

When clicked, the PC will prompt for a filename and location. Once saved, this file can be opened in

other programs such as spreadsheets, word processors, and databases.

OPEN FILE ICON

The OPEN FILE icon is located second from left. Click to open a file that has already been saved.

REAL TIME DATA LIST ICON

The LIST icon is located third from left on the main software

screen. When clicked, data is shown on the screen in list format

(shown at right). To save or print the list, click the SAVE or PRINT

icons in the Real Time List window.

EA15-EU-EN-V3.1 04/12

REAL TIME DATA GRAPH ICON

The REAL TIME GRAPH icon is located fourth from left. When clicked, the data is shown on an x-y

graph (see diagram below). The vertical axis represents the temperature units; the horizontal axis

represents the time.

Click on PRINT to get a hard copy of the graph. Press the

four-arrow icon (next to the PRINT icon) to select the data

range to be viewed. See diagram below:

SAMPLING TIME (RECORDING INTERVAL) ICON

The INTERVAL icon (2nd icon from right) allows the user to change the number of seconds that the

meter waits before logging a reading. If the interval is set to 5 seconds, the meter will record a

reading every 5 seconds. The range is 1 to 86,400 seconds.

MIN/MAX/AVG ICON

The AVG icon (3rd icon from right) allows the user to view maximum, minimum and average

readings for T1 and T2 inputs in real time when the meter is connected to the COM PORT via the

supplied cable. See screen capture below on left.

EA15-EU-EN-V3.1 04/12

Downloading Readings from the Meter to a PC

With the meter connected to the PC (as described earlier) and the

software running, click the datalogger download icon (first icon from the

right) to begin downloading data from the meter to the PC.

When the screen shown above right appears, select a set to view by

clicking on its number. A set is simply one datalogging session. Data will

be displayed in the data list format described earlier in the REAL TIME

DATA LIST ICON paragraph.

Once a data set has been selected, the

screen shown below will appear. Enter the

time of day datalogging began in HH:MM:SS

(hour/minute/second) format.

Maintenance

Cleaning

The meter can be cleaned with a damp cloth. A mild detergent may be used but avoid solvents,

abrasives, and harsh chemicals.

Battery Installation / Replacement

The battery compartment is located on the back of the meter. The compartment is easily accessed

by removing the ‘flat head’ screw on the back of the meter, and removing the compartment cover.

Replace or install the six ‘AAA’ batteries observing polarity and re-assemble the battery

compartment. Please dispose of batteries responsibly and in accordance with all regulations.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries

/ accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Storing

When the meter is to be stored, please remove the battery and affix the sensor’s protective cover.

Avoid storing the meter in areas of extreme temperature and humidity.

EA15-EU-EN-V3.1 04/12

Specifications

Measurement Ranges K - Type : -150.0oC to +1370.0oC (-200.0oF to +1999.9oF)

J - Type : -150.0oC to +1090.0oC( -200.0oF to +1994.0oF)

T - Type : -150.0oC to +400.0oC (-200.0oF to +752.0oF)

E - Type : -150.0oC to +870.0oC (-200.0oF to +1598.0oF)

R - Type : 0.0oC to +1767.0oC (+32oF to +1999.9oF)

S - Type : 0.0oC to +1767.0oC (+32oF to +1999.9oF)

N - Type : -150.0oC to +1300.0oC (-200.0oF to +1999.9oF)

Resolution J, K, T, E, N Type: 0.1oF/oC/K

R, S Type: 1.0oF/oC/K (0.1° for reference only)

Accuracy

J, K, T, E, N Type: ±(0.05% reading + 0.75oC (1.5°F)

below --100°C (148°F): add 0.15% of reading for J, K, E and N;

0.45% of reading for T; ±0.05 of reading +1°C(2°F) for R, S

Temperature Coefficient 0.01% of reading +0.06°F per °F (+0.03 °C) outside the specified

+18°C to 28°C (+64°F to 82°F) range

Below --100°C (148°F): add 0.04% of reading for J, K, E and N type;

and 0.08% of reading for T type

Note: Temperature accuracy does not include the accuracy of the probe.

Note: The temperature scale is based on the international temperature scale of 1990 (ITS90).

Display Dual Display Multi-function LCD with Backlight

Input Protection 60VDC; 24VAC rms

Measurement Rate 1 time per 1.5 second

Over range indication "OL" appears on the LCD

Open input indication "OL" appears on the LCD

Low battery indication “BT” appears on the LCD

Manual Memory Capacity 98 sets

Datalogging Memory Capacity 8800 sets

Power supply 6 ‘AAA’ Batteries

Battery life Approximately 200 hours with alkaline batteries

Operating Temperature 0 to 50oC (32 to 122oF)

Operating Humidity < 80% RH

Storage Temperature -10 to 60oC (14 to 140oF)

Storage Humidity 10 to 80% RH

Dimensions 150 x 72 x 35mm (5.91 x 2.8 x 1.4")

Weight Approx. 235g(8.29 oz) with batteries

www.extech.com

Inhaltsverzeichnis

Andere Extech Instruments Thermometer Handbücher

Extech Instruments

Extech Instruments EasyView EA20 Bedienungsanleitung

Extech Instruments

Extech Instruments 445715-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments 42525A Bedienungsanleitung

Extech Instruments

Extech Instruments RH35 Bedienungsanleitung

Extech Instruments

Extech Instruments EasyView EA11A Bedienungsanleitung

Extech Instruments

Extech Instruments RH490 Bedienungsanleitung

Extech Instruments

Extech Instruments 407907 Bedienungsanleitung

Extech Instruments

Extech Instruments K.J.E.T. 422324 Bedienungsanleitung

Extech Instruments

Extech Instruments RH210 Bedienungsanleitung

Extech Instruments

Extech Instruments 42540a Bedienungsanleitung

Extech Instruments

Extech Instruments IR200 Bedienungsanleitung

Extech Instruments

Extech Instruments 421502 Bedienungsanleitung

Extech Instruments

Extech Instruments 392050 Bedienungsanleitung

Extech Instruments

Extech Instruments 42515 Bedienungsanleitung

Extech Instruments

Extech Instruments 401014A Bedienungsanleitung

Extech Instruments

Extech Instruments 42510A Bedienungsanleitung

Extech Instruments

Extech Instruments IR301 Bedienungsanleitung

Extech Instruments

Extech Instruments 4465CF Bedienungsanleitung

Extech Instruments

Extech Instruments RH490-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments 42529 Bedienungsanleitung

Extech Instruments

Extech Instruments 42512 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT510 Bedienungsanleitung

Extech Instruments

Extech Instruments 42570 Bedienungsanleitung

Extech Instruments

Extech Instruments 445703 Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Microlife

Microlife NC 200 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung