Extech Instruments EasyView EA11A Bedienungsanleitung

User's Guide

EasyView™ K-Type Thermometer

Model EA11A

EA11A-EU-EN v1.3 01/14

WARNING

To avoid electrical shock or personal injury, do not apply more than

20Vrms between the thermocouple inputs or between the thermocouple

and earth ground

Introduction

Congratulations on your purchase of the Extech EasyView™ Thermometer. This device offers a

single K-type thermocouple input with multifunction LCD display. This meter is shipped fully tested

and calibrated and, with proper use, will provide years of reliable service.

Safety

To prevent personal injury or meter damage, use the meter only as specified in this guide

Meter Description

Meter

1. Thermocouple input connector

2. LCD display

3. Function buttons

4. Battery compartment (rear)

Display

1. Low battery

2. Primary display

3. Memory location

4. Auto power off

5. Secondary display

6. Max, Min and Average

7. Temperature units

8. Read from memory location

9. Store to memory location

10. Hold

11. Offset

EA11A-EU-EN v1.3 01/14

Operation

Connecting thermocouples

1. This meter accepts any K-type thermocouple with spade plugs (sub-miniature type with one

spade wider than the other).

2. Plug the thermocouple into the meter's thermocouple input jack.

Measuring

1. Press the button to turn power on. The meter will perform a short self-test.

2. Press the °C/°F button to select the desired temperature unit of measure. A display icon will

reflect the selection.

3. If a probe is not connected to the meter, the “--------” indication will appear on the display.

4. Contact the object to be measured with the probe.

5. Read the measured temperature in the display.

Note: If the display indicates “OL” the temperature is outside the measurement range.

Maximum, Minimum and Average Function

1. Press the MX/MN button to capture the Maximum (MX), Minimum (MN) and Average (AVG)

temperature values.

2. The lower secondary display will appear with MX and the maximum recorded temperature

displayed. The upper display will continue to measure the current temperature. The lower

display will update only when a new higher temperature is measured.

3. Press the MX/MN button to step through MX, MN and AVG.

4. The AVG value is the true average of the measured values. Averaging will occur for 4 hours,

then the average will reset and begin a new 4 hour cycle.

5. To exit the MX/MN function, Press and Hold the MX/MN button until the display returns to

standard operation.

Note: The Auto Power Off feature is disabled when the MX/MN feature is selected.

Data Hold

Press the HOLD button to freeze the reading in the display. The 'H' icon will appear on the top

center of the display. Press the HOLD button again to return to normal operation (the 'H' icon will

disappear).

Offset (Relative mode)

1. Press the Offset (relative) button to zero the displayed reading and to use that reading as a

reference for all future readings.

2. The OFFSET icon will appear in the display.

3. The stored reference value will appear in the lower secondary LCD display.

4. To exit the Offset function, Press and Hold the button until the display returns to standard

operation.

EA11A-EU-EN v1.3 01/14

Memory

The meter memory allows for the storage and recall of up to 150 temperature measurements.

1. Press the MEM button to store the reading into memory. “MEM” will briefly appear on the display

and the memory location will be indicated on the display.

2. Press the READ button to recall the data from the indicated memory location

a. “READ” and the stored value will appear in the display

b. Press the ▲▼buttons to step through the memory locations.

c. To exit the READ function, Press the READ button.

3. To clear data in memory

a. Turn the meter OFF

b. Press and Hold the MEM button and press the power button.

c. Release the MEM button and ALL CLr and NO will appear in the display.

d. Press the ▼button to select YES (delete data in memory) or NO (escape without

deleting).

e. Press the MEM button to implement the choice and exit the function.

Auto Power Off

To conserve battery life, the meter will go into the sleep mode if no button is pressed for 30 minutes.

“P” is displayed on the LCD when this feature is enabled.

To disable the feature:

1. With the meter OFF, Press and Hold the HOLD button and press the power button.

2. P and OFF will briefly appear on the display indicating that the auto power off feature is

disabled.

3. “P” will not be displayed.

Note: Auto power off is enabled every time the meter is powered on and is automatically disabled

when the MX/MN feature is enabled.

Battery Replacement

When the “BT” low battery icon appears in the display measurement accuracy may be affected.

Replace the 6 AAA batteries by removing the rear screw and battery compartment cover.

You, as the end user, are legally bound (Battery ordinance) to return all used batteries

and accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators at collection points in your

community or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Cleaning

Periodically wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents.

Wipe dry as necessary.

EA11A-EU-EN v1.3 01/14

Specifications

General Specifications

Display Multi-function LCD

Measurement Range -50 to 1300oC (-58 to 1999oF)

Resolution 0.1oC/oF <200o, 1oC/oF >200o

Data Memory 150 sets

Input Protection 20V maximum

Display Update Rate 2.5 times per second

Over range indication "OL" appears on the LCD

Open input indication "-------" appears on the LCD

Auto Power OFF 30 minutes (if no key is pressed)

Low battery indication “BT” appears on the LCD

Power supply 6 AAA Batteries

Battery life Approximately 110 hours with carbon zinc batteries

Operating Temperature 0 to 50oC (32 to 122oF)

Operating Humidity < 80% RH

Storage Temperature -10 to 60oC (14 to 140oF)

Storage Humidity < 70% RH

Altitude up to 2000 meters

Approvals

Dimensions 150x72x35mm (5.91x2.8x1.4")

Weight Approx. 235g (8.29 oz.) with battery

Accuracy Specifications

Units Range Accuracy (@23 ± 5oC)

0oF to 1832oF ±(0.3% reading + 2oF)

-58oF to 0oF and

1832oF to 1999oF ±(0.5% reading + 2oF)

0oC to 1000oC ±(0.3% reading + 1oC)

-50oC to 0oC and

1000oC to 1300oC ±(0.5% reading + 1oC)

Temperature Coefficient 0.1 times the applicable accuracy specifications per oC from 0oC to

18oC and 28oC to 40oC (32oF to 64oF and 82oF to 104oF)

Note: Temperature accuracy does not include the accuracy of the type K probe.

Note: The temperature scale is based on the international temperature scale of 1990 (ITS90).

ISO-9001 Certified

www.extech.com

Inhaltsverzeichnis

Andere Extech Instruments Thermometer Handbücher

Extech Instruments

Extech Instruments EA15 Bedienungsanleitung

Extech Instruments

Extech Instruments 42540a Bedienungsanleitung

Extech Instruments

Extech Instruments 42529 Bedienungsanleitung

Extech Instruments

Extech Instruments RH30 Bedienungsanleitung

Extech Instruments

Extech Instruments EzSmart RHT3 Bedienungsanleitung

Extech Instruments

Extech Instruments 407445 Bedienungsanleitung

Extech Instruments

Extech Instruments 42535 Bedienungsanleitung

Extech Instruments

Extech Instruments RH250W Bedienungsanleitung

Extech Instruments

Extech Instruments 392050 Bedienungsanleitung

Extech Instruments

Extech Instruments 42509 Bedienungsanleitung

Extech Instruments

Extech Instruments RH101 Bedienungsanleitung

Extech Instruments

Extech Instruments IR301 Bedienungsanleitung

Extech Instruments

Extech Instruments 42540 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT510 Bedienungsanleitung

Extech Instruments

Extech Instruments RH350 Bedienungsanleitung

Extech Instruments

Extech Instruments IRC130 Bedienungsanleitung

Extech Instruments

Extech Instruments TM300 Bedienungsanleitung

Extech Instruments

Extech Instruments 42555 Bedienungsanleitung

Extech Instruments

Extech Instruments RHM15 Bedienungsanleitung

Extech Instruments

Extech Instruments RHM15 Bedienungsanleitung

Extech Instruments

Extech Instruments 42511 Bedienungsanleitung

Extech Instruments

Extech Instruments MD13628 Bedienungsanleitung

Extech Instruments

Extech Instruments IR200 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT510-NIST Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Microlife

Microlife NC 200 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung