Extech Instruments RH401 Bedienungsanleitung

User Manual

Digital Psychrometer + IR Thermometer

Model RH401

AdditionalUserManualTranslationsavailableatwww.extech.com

umi

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

umi

Introduction

Congratulations on your purchase of the Extech RH401 Digital Psychrometer + InfraRed

Thermometer. This device measures Humidity, Air Temperature, Dew Point and Wet Bulb.

Advanced features include Infrared Non-Contact Surface Temperature Measurement, Data Hold and

programmable Auto Power Off, and an RS-232 interface for capturing readings to a PC using

optional 407752 software. The retractable probe protects the sensors when the meter is not in use.

Careful use of this meter will provide years of reliable service.

Meter Description

1. Emissivity adjust indicator

2. Laser pointer on indicator

3. Low Battery indicator

4. IR Surface Temperature button

5. ON/OFF/Setup button

6. Back Light button

7. Laser/Down button

8. °F/°C/Up button

9. Dew Point/Wet Bulb button

10. % Humidity display

11. Air Temperature, Dew Point or Wet Bulb display

12. IR Surface Temperature display

13. Extended probe with Humidity &

Air Temperature Sensors

14. PC interface port

15. AC adaptor jack

Note: The battery compartment is located on the rear of the instrument

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

Operation

Retractable Humidity and Air Temperature Sensor

Press down on the sensor, located at the top of the meter, to release it.

Humidity and air temperature will not be displayed if the sensor is not

extended.

After use, press the sensor into the stored (protected) position.

Power ON/OFF

Press the (or the button) to turn power on. The meter will

perform a short self-test when turned on.

Press and hold the button for three seconds to turn power off.

Humidity and Air Temperature measurements

1. Hold the meter in the area to be tested.

2. Allow adequate time for readings to stabilize.

3. View the Relative Humidity measurement in the lower display.

4. View the Air (probe)Temperature measurement in the middle display

Wet Bulb and Dew Point measurements

1. To display the Dew Point measurement, momentarily press the button until the symbol

DP appears in the middle display.

2. Dew Point temperature is now displayed.

3. To display the Wet Bulb measurement, momentarily press the button until the symbol

Wb appears in the middle display .

4. Wet Bulb temperature is now displayed.

5. To display the IR surface temp – DP temp temperature press and hold the button for

more than 2 seconds. The icon will appear in the top left corner of the display, then press the

IR Temp button. The differential temperature reading can now be viewed in the top display.

6. Press and hold the button for more than 2 seconds to toggle the display back to IR

temperature.

Non-Contact InfraRed Surface Temperature measurements

1. Point the meter toward the surface to be measured.

2. Press and hold the button.

3. View the temperature measurement in the upper display

4. Release the nd the reading will be held on the display until a new reading is taken.

5. While holding down the button, press the button to toggle the laser targeting

pointer on/off. The symbol will appear in the middle left of the display indicating that surface

temperature measurement is active and the laser pointer is on.

WARNING! The Laser button enables/disables the Laser pointer. When enabled, each

press of the button turns on the Laser beam. Avoid looking directly into the path of the

Laser or pointing the Laser toward anyone’s eyes. Mirrored surfaces near a measurement object

can redirect the Laser, use extreme caution. Do not allow the Laser beam to be directed toward

explosive gases.

Sensor

Extended

Stored

Sensor

Press Here

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

IR Emissivity Adjustment

Emissivity is adjustable from 0.3 to 0.99. The default value is 0.95 which is the typical emissivity

value of many non-metallic surfaces. If the surface to be measured is highly reflective and the

emissivity is not known, cover the surface with paint or tape to improve measurement accuracy. If

the emissivity of the surface is known, follow this procedure to set the value.

1. With the meter on, Press the key twice to enter the Emissivity setting procedure.

will flash on the top left side of the display.

2. Use the up key and the down key to adjust the value.

3. When the desired setting appears in the display, press again to save and return back to

normal operation.

Emissivity Factors for Common Materials

Material under test Emissivity Material under test Emissivity

Asphalt 0.90 to 0.98 Cloth (black) 0.98

Concrete 0.94 Skin (human) 0.98

Cement 0.96 Lather 0.75 to 0.80

Sand 0.90 Charcoal (powder) 0.96

Soil 0.92 to 0.96 Lacquer 0.80 to 0.95

Water 0.92 to 0.96 Lacquer (matt) 0.97

Ice 0.96 to 0.98 Rubber (black) 0.94

Snow 0.83 Plastic 0.85 to 0.95

Glass 0.90 to 0.95 Timber 0.90

Ceramic 0.90 to 0.94 Paper 0.70 to 0.94

Marble 0.94 Chromium Oxides 0.81

Plaster 0.80 to 0.90 Copper Oxides 0.78

Mortar 0.89 to 0.91 Iron Oxides 0.78 to 0.82

Brick 0.93 to 0.96 Textiles 0.90

Spot to Distance Ratio

The 8:1 spot to distance ratio determines the size of the measured surface area with respect to the

distance the meter is held away from the surface.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

Selecting temperature units of measure (C/F)

Press and hold the oC/oF button momentarily to toggle the temperature units.

Automatic Power OFF

The meter automatically shuts off after a programmed period of time.

To disable auto power off, with the meter off, press and . When “n” appears, release

the keys and the meter is now in Non-Sleep Mode.

The power off time is adjustable from 5 to 600 seconds. To change the auto power off setting, press

the key to enter the setting procedure. Use the up key and the

down key to set the value. When the desired power-off time appears in the display, press

the key again to save the parameters.

Backlight

Press the BKLT button to turn the display backlight on. The backlight will remain on until the BKLT

button is pressed again or the meter is turned off.

Error Messages

An error message will appear on the display if the meter fails an internal diagnostic test.

1. E1 (Top display): IR temperature failure. Repair/replacement is necessary.

2. E2 (Top display): IR temperature >932°F (500°C).

3. E3 (Top display): IR temperature <-40°F (-40°C).

4. E9 (Top display): Calibration error.

5. E1 (Middle display): Temperature failure. Repair/replacement is necessary.

6. E2 (Middle display): Dew Point is out of range or Repair/replacement is necessary.

7. E3 (Middle display): Air temperature is out of range or Repair/replacement is necessary.

8. E1 (Bottom display): RH circuit error. Repair/replacement is necessary.

9. E5 (Bottom display): RH circuit error. Repair/replacement is necessary.

Setup memory

The selected display, emissivity value, auto power off time, backlight status and the laser pointer

status are stored in memory and will remain in memory as the user default setting until

reprogrammed by the user.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

Calibration

The following verification and calibration procedures requires a humidity chamber or the 33% and

75% RH reference bottles which are supplied with the Model RH300-CAL kit.

RH Accuracy Verification

Checking the 33% or 75% RH Calibration

1. Insert meter’s sensor into the 33% or 75% salt reference

bottle.

Rotating the bottle will assist in placing it over the sensor.

2. Check the reading after 10 minutes

3. Verify that the reading is within the accuracy specification.

RH Calibration (33% and 75%)

This two-point calibration takes approximately one hour to

complete.

33% Calibration

1. Turn off the meter and insert the meter sensor into the 33%

salt reference bottle. Rotating the bottle will assist in

placing it over the sensor.

2. Hold down the and keys and then press the

key to turn the unit on.

3. “32.8” (reading may vary depending on temperature) will

flash on the display. After 30 minutes, the flashing will stop

to indicate that the 33% calibration is complete.

75% Calibration

4. Insert the meter sensor into the 75% salt reference bottle. From a steady “32.8” display

press the button to enter the 75% calibration.

5. “75.2” (reading may vary depending on temperature) will flash on the display. After 30

minutes, the flashing will stop to indicate that the 75% calibration is complete and the

calibration data has been saved to memory.

6. The screen will return to the normal display. Calibration is now complete.

Note: If the salt at the bottom of the calibration bottles appears dry, the bottles should be

replaced.

33% or 75%

Cal Bottle

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

RS-232 PC Communications Interface

The meter is equipped with an RS-232 PC interface jack (3.5mm phono) for connection to a PC.

The cable to connect the meter to the PC is included in the optional 407752 data acquisition kit. The

kit includes WindowsTM compatible software that allows the user to store readings in a text file and

display real-time measurements in a series of selectable formats. For more information or specific

operating instructions, refer to the User Guide included with the 407752 kit or contact Extech

Instruments.

Specifications

Function Range and Resolution Accuracy

Humidity 0.0 to 100.0% RH ±3% RH (10 to 90%)

Temperature (Air) -4.0 to 122.0oF (-20 to 50oC) ±1.8oF (±1oC)

Temperature (InfraRed)

(@25ºC ±5ºC)

-4 to 842oF (-20 to 450oC) ±3% reading or ±3oC/6oF

whichever is greater

-40 to -4oF, 842 to 932oF

-40 to -20oC, 450 to 500oC ±4% reading or ±4oC/8oF

whichever is greater

Display Triple LCD with backlight

Sensor Type Humidity: Capacitance sensor; Temperature (air): Thermistor

Dew Point -90.4 to 122.0oF (-68 to 50oC) (calculated from humidity and

temperature measurements)

Wet Bulb -6.9 to 122.0oF (-21.6 to 50oC) (calculated from humidity and

temperature measurements)

IR Emissivity Adjustable from 0.3 to 0.99

IR Spot/Distance Ratio 8:1

IR Response Time 0.5 seconds

Operating Conditions -4 to 122oF (-20 to 50oC); < 99% RH non-condensing

Storage Conditions -40 to 185oF (-40 to 85oC); <99% RH non-condensing

Power Supply 4 x 1.5V ‘AAA’ batteries or AC adaptor

Battery Life approx. 150 hours (laser inactive); 30 hours (laser active)

Dimensions / Weight 6.8x2.7x1.9” (175x70x50mm); 4.9 oz. (140g)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RH401-en-GB_ V1.7 1/17

Maintenance

Cleaning and storage

1. The meter should be cleaned with a damp cloth and mild detergent when necessary. Do not use

solvents or abrasives.

2. Store the meter in an area with moderate temperature and humidity (refer to the operating and

storage range in the specifications chart earlier in this manual).

Battery Replacement

When the battery power falls low, the symbol will appear on the lower left of the LCD. Replace the

four (4) 1.5 ‘AAA’ batteries by removing the rear battery compartment cover and accessing the

battery compartment. Observe polarity when placing the batteries in the compartment. Ensure that

the compartment cover is securely fastened when finished.

Repair Services

Extech offers repair and calibration services for most of the products we sell. Call the Customer

Service Department for information on repair services available for this product.

[email protected] or call 1-603-324-7800 press 4.

Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Inhaltsverzeichnis

Andere Extech Instruments Thermometer Handbücher

Extech Instruments

Extech Instruments RH490 Bedienungsanleitung

Extech Instruments

Extech Instruments 42509 Bedienungsanleitung

Extech Instruments

Extech Instruments EA15 Bedienungsanleitung

Extech Instruments

Extech Instruments HD550 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL200 Bedienungsanleitung

Extech Instruments

Extech Instruments RH200W Bedienungsanleitung

Extech Instruments

Extech Instruments SDL500 Bedienungsanleitung

Extech Instruments

Extech Instruments 42515 Bedienungsanleitung

Extech Instruments

Extech Instruments 4465CF Bedienungsanleitung

Extech Instruments

Extech Instruments 392050 Bedienungsanleitung

Extech Instruments

Extech Instruments 445703 Bedienungsanleitung

Extech Instruments

Extech Instruments 421504 Bedienungsanleitung

Extech Instruments

Extech Instruments EasyView Dual K EA10 Bedienungsanleitung

Extech Instruments

Extech Instruments 445715 Bedienungsanleitung

Extech Instruments

Extech Instruments RH10 Bedienungsanleitung

Extech Instruments

Extech Instruments IR400 Bedienungsanleitung

Extech Instruments

Extech Instruments TM100 Bedienungsanleitung

Extech Instruments

Extech Instruments IR201A Bedienungsanleitung

Extech Instruments

Extech Instruments SDL200-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments 42540 Bedienungsanleitung

Extech Instruments

Extech Instruments EA25 Bedienungsanleitung

Extech Instruments

Extech Instruments 42525A Bedienungsanleitung

Extech Instruments

Extech Instruments RH350 Bedienungsanleitung

Extech Instruments

Extech Instruments IR267 Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Microlife

Microlife NC 200 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung