Extreme Networks AP-7532 Bedienungsanleitung

AP-7532 Access Point

Installation Guide

Published June 2017

9035112

Published June 2017

9035112

Legal Notices

Extreme Networks, Inc. reserves the right to make changes in specifications

and other information contained in this document and its website without

prior notice. The reader should in all cases consult representatives of Extreme

Networks to determine whether any such changes have been made.

The hardware, firmware, software or any specifications described or referred

to in this document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or

registered trademarks of Extreme Networks, Inc. in the United States and/or

other countries.

All other names (including any product names) mentioned in this document

are the property of their respective owners and may be trademarks or

registered trademarks of their respective companies/owners.

For additional information about Extreme Networks trademarks, go to:

www.extremenetworks.com/company/legal/trademarks/

Support

For product support, phone the Global Technical Assistance Center (GTAC) at

1-800-998-2408 (toll-free in U.S. and Canada) or +1-408-579-2826. For the

support phone number in other countries, visit: www.extremenetworks.com/

support/contact/

For product documentation online, visit: www.extremenetworks.com/

documentation/

Contents

Introduction ...............................................................................................................3

Document Conventions ..................................................................................................................................................3

Warnings ...............................................................................................................................................................................3

Site Preparation ................................................................................................................................................................ 4

AP-7532 Package Contents ......................................................................................................................................... 4

Features ...........................................................................................................................................................................................4

AP-7532 Antennas ........................................................................................................................................................... 4

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - US .................................................................................................... 4

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - EMEA .............................................................................................. 5

AP-7532 Internal Antenna Model .......................................................................................................................................... 5

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - Canada .......................................................................................... 6

Hardware Installation ...............................................................................................7

Precautions ..........................................................................................................................................................................7

Access Point Placement ................................................................................................................................................ 8

Power Injector System ................................................................................................................................................... 8

Wall Mount Instructions ................................................................................................................................................10

Wall Mount Procedure - New Installation ..........................................................................................................................11

Wall Mount Procedure - Existing Access Point Replacement ..................................................................................12

Suspended Ceiling T-Bar Mount Instructions ...................................................................................................... 12

LED Indicator ..................................................................................................................................................................... 15

Basic Access Point Configuration......................................................................... 19

AP-7532 Access Point Specifications ..................................................................27

Electrical Characteristics ............................................................................................................................................. 27

Physical Characteristics ............................................................................................................................................... 27

Radio Characteristics ....................................................................................................................................................28

Regulatory Information......................................................................................... 29

Wireless Device Country Approvals .......................................................................................................................29

Declaration of Conformity in Languages of the European Community ..............................................................29

Country Selection ..................................................................................................................................................................... 30

Frequency of Operation – FCC and IC ............................................................................................................................. 30

Health and Safety Recommendations ...................................................................................................................30

Warnings for the use of Wireless Devices ........................................................................................................................31

Potentially Hazardous Atmospheres – Fixed Installations .......................................................................................32

Safety in Hospitals .....................................................................................................................................................................32

RF Exposure Guidelines ............................................................................................................................................... 32

Safety Information .....................................................................................................................................................................32

International .................................................................................................................................................................................32

EU .....................................................................................................................................................................................................33

US and Canada ...........................................................................................................................................................................33

Power Supply ...................................................................................................................................................................34

Radio Frequency Interference Requirements—FCC ........................................................................................34

AP-7532 Access Point Installation Guide

Contents

Radio Transmitters (Part 15) ..................................................................................................................................................34

Radio Frequency Interference Requirements - Canada ............................................................................................34

CE Marking and European Economic Area (EEA) ............................................................................................36

Statement of Compliance ...........................................................................................................................................36

Japan (VCCI) - Voluntary Control Council for Interference ..........................................................................36

Korea Warning Statement for Class B ITE ...........................................................................................................36

Other Countries ...............................................................................................................................................................36

Waste Electrical and Electronic Equipment (WEEE) .......................................................................................38

TURKISH WEEE Statement of Compliance .........................................................................................................39

End-User License Agreement................................................................................ 41

AP-7532 Access Point China ROHS Compliance............................................... 47

3AP-7532 Access Point Installation Guide

Introduction

The AP-7532 external antenna and internal antenna Access Point’s are mid-tier Access

Point’s with a relatively small footprint which supports functionality for dependable and

efficient network performance.The AP-7532 is a 3x3:3 802.11ac Access Point utilizing one 2.4

GHz 802.11n radio and one 5 GHz 802.11ac radio. The Access Point housing is Plenum-rated

(UL2043).

The Access Point’s unique WiNG 5 software enables the Access Point to function as either a

Standalone Access Point, an Adaptive Access Point, or a Virtual Controller.

If new to Access Point technology, refer to the WiNG Access Point System Reference Guide

to familiarize yourself with Access Point technology and the feature set supported by the

WiNG operating system. The guide is available at www.extremenetworks.com/support.

This document is written for the qualified network device installer.

Document Conventions

The following graphical alerts are used in this document to indicate notable situations.

Warnings

• Read all installation instructions and site survey reports, and verify correct equipment

installation before connecting the AP-7532 Access Point.

• Remove jewelry and watches before installing this equipment.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures

meet equipment operation specifications.

NOTE

Tips, hints, or special requirements that you should take note of.

CAUTION

Care is required. Disregarding a caution can result in data loss or equipment

malfunction.

WARNING

Indicates a condition or procedure that could result in personal injury or

equipment damage.

Introduction

AP-7532 Access Point Installation Guide 4

Site Preparation

• Consult your site survey and network analysis reports to determine specific

equipment placement, power drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal

transmission.

AP-7532 Package Contents

An AP-7532 Access Point is available in both external antenna (AP-7532) and internal

antenna (AP-7532I) configurations. An AP-7532 ships with the following:

• AP-7532 Access Point

• AP-7532 Installation Guide (This Guide)

• Wall mount screws and mounting bracket

Features

An AP-7532 Access Point supports the following feature set:

• Two RJ-45 connectors (GE1/POE and Console)

•TwoLEDindicators

• One 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio

• 3x3 MIMO, 3 spatial streams

The GE1/POE accepts 802.3at or 802.3af compliant power from an external source.

AP-7532 Antennas

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - US

An AP-7532 external antenna Access Point supports the following dual band antenna

options for the US:

Note

When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is

recommended for Gigabit operation.

Introduction

AP-7532 Access Point Installation Guide 5

* This antenna is for indoor placement only.

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - EMEA

An external antenna AP-7532 supports the following dual band antenna options for the

EMEA:

AP-7532 Internal Antenna Model

An AP-7532 internal antenna Access Point supports the following dual band antenna:

Note

Per FCC requirement, the use of the Access Point on UNII-1 of 5GHz band requires

installers to input antenna elevation gain during configuration if the AP placement is

for outdoor coverage.

Part Number

Antenna

Type

2.4 GHZ

Gain (dBi)

5 GHZ

Gain (dBi)

Elevation Gain for

outdoor

placement (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85 na*

ML-2452-HPA5-036 Dipole 3 5 na*

ML-2452-APAG2A1-01 Dipole 2.7 1.7 na*

ML-2452-PNL9M3-N36 Polarized-

Panel

11 10.7 7.3

ML-2452-PNA5-01R Panel 5.5 6 5.2

ML-2452-PTA3M3-036 Patch 5 4 na*

ML-2452-VMM5M3-

N72

Patch 4.5 5.4 2.9

Part Number Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85

ML-2452-HPA5-036 Dipole 3 5

ML-2452-APAG2A1-01 Dipole 2.7 1.7

ML-2452-HPAG4A6-01 Dipole 47.3

ML-2452-HPA6-01 Dipole 5.3 6.1

ML-2452-PNL6M3-N36 Polarized-Panel 6 6

ML-2452-PNA5-01R Panel 5.5 6

ML-2452-PTA3M3-036 Patch 5 4

ML-2452-VMM5M3-N72 Patch 4.5 5.4

Introduction

AP-7532 Access Point Installation Guide 6

AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - Canada

*An external antenna AP-7532 supports the following dual band antenna options for

Canada:

Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

PIFA 4.13 5.92

Part Number Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85

ML-2452-HPA5-036 Dipole 3 5

ML-2452-APAG2A1-01 Dipole 2.7 1.7

ML-2452-PNL9M3-N36 Polarized -Panel 11 10,7

ML-2452-PNA5-01R Panel 5.5 6

ML-2452-PTA3M3-036 Patch 5 4

ML-2452-VMM5M3-

N72

Patch 4.5 5.4

Note

A professional installer must enter the antenna type, gain, and indoor/outdoor

placement using the CLI. The AP software will then use this information and hardcode

maximum limits determined during testing to limit the EIRP. Please note that the

maximum EIRP in band 5.25-5.35GHz will be limited to 23dBm. This limit is hardcoded

in the software for this band.

7AP-7532 Access Point Installation Guide

Hardware Installation

An AP-7532 Access Point mounts either on a wall (with M 3.5 x 0.6 x 23 MM pan head

screws and mounting bracket- or equivalent) or on a suspended ceiling T-bar.

To prepare for the installation:

1 Match the part number on the purchase order with the part numbers in the packing list

and on the case of the Access Point.

2 Verify the contents of the box include the intended AP-7532 Access Point, and the

included hardware matches the package contents.

3 Review site survey and network analysis reports to determine the location and mounting

position for the AP-7532 Access Point.

4 Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power

source and run the cable to the installation site. Ensure there is sufficient slack on the

cable to perform the installation steps.

Precautions

Before installing an AP-7532 Access Point, verify the following:

• Your are using the correctly rated power solution for the AP-7532 (either the AP-

PSBIAS-2P3-ATR power injector or the PWRS-14000-54R external power supply)

• Do not to install the AP-7532 in wet or dusty areas.

• Verify the environment has a continuous temperature range between -4° F to 104° F/

-20° C to 40° C for external antenna Access Points and 32° F to 104° F/0° C to 40° C

for internal antenna Access Points.

Part Number Description

AP-7532-67040-US AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point

external antenna

US version

AP-7532-67040-1-WR AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point

external antenna International version

AP-7532-67030-US AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point

internal antenna

US version

AP-7532-67030-1-WR AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point

internal antenna International version

NOTE

When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is

recommended for Gigabit operation.

Hardware Installation

AP-7532 Access Point Installation Guide 8

Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty

motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment.

Signal loss can occur when metal, concrete, walls or floors block transmission. Install the

Access Point in an open area or add Access Points as needed to improve coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be

not bright enough. An area lit sharply might minimize coverage and create dark areas.

Uniform antenna placement in an area (like even placement of a light bulb) provides even,

efficient coverage.

Install the Access Point at an ideal height of 10 feet from the ground.

To maximize the Access Point’s radio coverage area, recommends conducting a site survey

to define and document radio interference obstacles before installing the Access Point.

Power Injector System

An AP-7532 Access Point can receive power via an Ethernet cable connected to the GE1/

POE (LAN) port.

When users purchase a WLAN solution, they often need to place Access Points in obscure

locations. In the past, a dedicated power source was required for each Access Point in

addition to the Ethernet infrastructure. This often required an electrical contractor to install

power drops at each Access Point location. The Power Injector merges power and Ethernet

into one cable, reducing the burden of installation and allowing optimal Access Point

placement in respect to the intended coverage area.

The AP-7532’s supported Power Injector (Part No. AP-PSBIAS-2P3-ATR) is a high power

POE Injector delivering up to 30 watts. The Access Point can only use a Power Injector

when connecting the unit to the Access Point’s GE1/POE port. The Power Injector is

separately ordered and not shipped with an existing AP SKU.

CAUTION

Using a non-compliant injector, or an injector supporting legacy modes will not allow

the AP-7532 to function at optimum performance levels.

CAUTION

Do not plug the AP-PSBIAS-2P3-ATR Power Injector into the Access Point’s Console

port. Connecting the Power Injector into the console port can damage the port and

void the AP-7532’s product warranty.

Inhaltsverzeichnis

Andere Extreme Networks Zugangspunkt Handbücher

Extreme Networks

Extreme Networks AP-8533 Bedienungsanleitung

Beliebte Zugangspunkt Handbücher anderer Marken

LevelOne

LevelOne WAP-6101 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Meru Networks

Meru Networks ap400 Bedienungsanleitung

Tranzeo Wireless Technologies

Tranzeo Wireless Technologies EL-500 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-IW Bedienungsanleitung

LevelOne

LevelOne WAP-8101 Bedienungsanleitung

Pakedge

Pakedge WK-1-C Bedienungsanleitung

EnGenius

EnGenius EWS550AP Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Edge-Core

Edge-Core ECW5320 Bedienungsanleitung

Ruijie

Ruijie RG-AP130(W2) Installations- und Betriebsanleitung

Intellinet

Intellinet 524711 Bedienungsanleitung

Zoomnet

Zoomnet Bgate-GT10-D24-N22-P Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WAP-PC1200C Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket AC R5AC-PTMP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW Bedienungsanleitung

Ruijie Networks

Ruijie Networks RG-AP520-I(G2) Series Installations- und Betriebsanleitung

Hamlet

Hamlet Wireless Access Point 150 Bedienungsanleitung