Extreme Networks WS-AP3801i Bedienungsanleitung

Overview of the WS-AP3801i

The WS-AP3801i is designed to extend your Wireless LAN

around indoor locations. The WS-AP3801i supports the

802.11ac wireless standards, with full backward

compatibility with legacy 802.11a, 802.11b, 802.11g, and

802.11n devices. The WS-AP3801i interoperates fully with

Wireless LANs, including support for VoWLAN, branch

office mode, guest services, RTLS, availability, and mobility.

WS-AP3801i models have the following features:

• Radios: 2 radios (2.4 GHz or 5 GHz)

• LEDs: 4 (see Figure 2)

• Power: <12.95W; 802.3af (see Ta b l e 1 )

• Antennas:

– 4 internal single band antenna assemblies

• Mounting brackets for 15/16” drop ceiling T-bar rail:

– 1 protruded drop ceiling rail bracket

– 1 flat drop ceiling rail bracket

Figure 1 displays a front and back view of the WS-AP3801i.

Figure 1 Front & Back View of the AP3801i

Ta b l e 1 shows ways to power the WS-AP3801i.

Note: WS-AP3801i Rev 5F and above requires a minimum

base firmware of 9.21.10.

1Power LED 4LAN Port

2LEDs 5Kensington Lock Slot

3External DC Power Supply

Port

Table 1 Powering the WS-AP3801i

Power

Source Description

Power over

Ethernet

(PoE)

Power is provided through the RJ45 Ethernet port

(LAN port) on the top of the WS-AP3801i. This is the

preferred method of powering the AP on ceiling and

high wall installations.

External 12V

DC power

supply

(optional)

The WS-AP3801i can also be powered by an

external DC power supply plugged into an AC

source. Plug the supply’s input jack into the DC-In

port (callout 3 in Figure 1).

Figure 2 shows the LEDs on the front of the WS-AP3801i.

Figure 2 LEDs on AP Front Face

Green LEDs mean ON. Amber LEDs mean OFF.

For detailed installation information about the WS-AP3801i,

see the Extreme Networks IdentiFi Wireless AP3805

Installation Guide.

Mounting and Connecting the AP

A wall mount bracket is included for quick and easy

mounting of the WS-AP3801i to a wall. Additionally, a

ceiling mounting kit is provided for mounting the AP to a

drop ceiling. Use these instructions as guidelines for

mounting and connecting the WS-AP3801i easily and

safely.

Mounting on a Drop Ceiling

Figure 3 and Figure 4 shows the T-bar rail connector being

mounted to the AP3801i.

Figure 3 Attaching the T-bar Rail Connectors to the AP

1 Attach the T-bar rail connectors (see Figure 3, Item 2) to

the bottom cover of the AP using the provided short

screws (see Figure 3, Item 1). Two sizes of T-bar rail

connectors are included in the mounting hardware kit:

15/16 in (2.38 cm) and 9/16 in (1.43 cm).

2 If extra space is required to accommodate drop ceiling

tiles, use the provided spacers and long screws (see

Figure 3, Items 1 and 3).

3 Remove the ceiling panels around the drop ceiling T-bar

rails where you intend to mount the AP.

1AP Status 3Radio 2

2Radio 1

Electrical Hazard: Only qualified personnel should perform

installation procedures.

4 Verify that the Ethernet cable that will connect to the AP

can reach the AP at the point where you plan to mount it.

5 Line up the connected T-bar rail connectors (see

Figure 4, Item 2) with an appropriately sized rail (see

Figure 4, Item 1), and press the AP onto the rail until it

snaps into place as shown in Figure 4. With both bracket

tabs over the T-bar rail lips, tap the AP to verify it is

stable and won’t fall off. Figure 4 illustrates the AP and

bracket mounted on a T-bar rail.

Figure 4 WS-AP3801i Mounted on Drop Ceiling T-bar

Rail

6 Make a hole through the ceiling panel closest to the

power slot on the AP. Run the Ethernet cable through the

hole and into an RJ45 LAN port in the recessed

connector bay.

7 Replace the displaced ceiling panels.

Mounting on a Wall or Solid Flat Ceiling

Figure 5 shows the AP3801i being mounted to a wall or

solid ceiling.

Figure 5 Mounting the WS-AP3801i to a Flat Wall or

Solid Ceiling

1 Determine the spot on the wall where the AP is to be

mounted, preferably high up on the wall (near the ceiling

for maximum radio wave dispersion) but in reach of the

Ethernet cable and a wall power outlet if you are not able

to use Power over Ethernet.

2 Drill two holes in the wall (see Figure 5, Item 1) to match

the center of the two keyhole slots in the back of the AP

bracket (see Figure 5, Item 3). For a tight fit, the holes

should be slightly smaller than the diameter of the

provided plastic anchors.

3 Screw the anchors (see Figure 5, Item 2) into the holes

until they are flush with the wall, and screw the provided

mounting screws (see Figure 5, Item 5) into the anchors.

4 Screw the AP mounting screws (see Figure 5, Item 4)

into the bottom of the AP.

5 Mount the AP on the mounting bracket by aligning the

mounting screw with the slots in the bracket and rotating

the unit clockwise about 90 degrees to secure it in place.

Figure 5 shows an exploded view of this mounting

method.

Connecting a Power Supply to the WS-AP3801i

If you need to power the WS-AP3801i with an external 12V

DC power supply, you can plug the power cord into the

power connector (see Figure 1, Item 6) on the back of the

AP. There is no wall mount for the 12V DC power supply.

When the device is powered on, the power LED on the front

face of the AP is lit. Refer to the Extreme Networks IdentiFi

Wireless AP3805 Installation Guide for information about

optional power supplies.

LAN Connection

The WS-AP3801i has one LAN (Ethernet) port (see Figure 1,

Item 7). During administration and maintenance through

the LAN, the AP must still have a power connection

through either an Ethernet PoE cable or a DC power supply.

Note: LAN connectors with shrouds will not fit into the AP

port. Remove the shroud or use an optional jumper cable.

Notice

Legal Notices

Extreme Networks, Inc., on behalf of or through its wholly-owned

subsidiary, Enterasys Networks, Inc., reserves the right to make

changes in specifications and other information contained in this

document and its website without prior notice. The reader should

in all cases consult representatives of Extreme Networks to

determine whether any such changes have been made.

The hardware, firmware, software or any specifications described

or referred to in this document are subject to change without

notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks

or registered trademarks of Extreme Networks, Inc. in the United

States and/or other countries.

All other names (including any product names) mentioned in this

document are the property of their respective owners and may be

trademarks or registered trademarks of their respective

companies/owners.

For additional information on Extreme Networks trademarks,

please see: www.extremenetworks.com/company/legal/

trademarks/

Documentation & Support

For product support, including documentation, visit:

www.extremenetworks.com/support/

Contact

Extreme Networks, Inc.

145 Rio Robles

San Jose, CA 95134 USA

Tel: +1 408-579-2800

Toll-free: +1 888-257-3000

Regulatory and Compliance Information

Safety Guidelines

This section contains notices that are intended to protect your

personal safety and prevent damage to the equipment.

Qualified Personnel:

RF Safety Distance

The antennas used for this transmitter must be installed to provide

a separation distance of at least 22 cm from all persons and must

not be co-located or operating in conjunction with another

antenna or transmitter.

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Electrical Hazard: Only qualified personnel should perform

installation procedures. Within the context of the safety

notes in this documentation, qualified persons are defined

as persons who are authorized to commission, ground and

label devices, systems, and circuits in accordance with

established safety practices and standards. A qualified

person understands the requirements and risks involved

with installing outdoor electrical equipment in accordance

with national codes.

Warning: Changes or modifications made to this device

which are not expressly approved by the party responsible

for compliance could void the user’s authority to operate

the equipment.

Industry Canada Notice

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus set out in the Radio

Interference Regulations for the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits

radioélectriques dépassant les limites applicables aux appareils

numériques de la class B prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des

Communications du Canada.

Suitable for use in environmental air space in accordance with

Section 300.22.C of the National Electrical Code, and Sections 2-

128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1,

C22.1.

Convient à l'espace de ventilation environnemental, conformément

à la section 300.22.C du Code national de l'électricité et aux

sections 2-128, 12-010(3) et 12-100 du Code canadien de

l'électricité, partie 1, C22.1.

European Waste Electrical and Electronic

Equipment (WEEE) Notice

In accordance with Directive 2012/19/EU of the European

Parliament on waste electrical and electronic equipment (WEEE):

1 The symbol above indicates that separate collection of electrical

and electronic equipment is required.

2 When this product has reached the end of its serviceable life, it

cannot be disposed of as unsorted municipal waste. It must be

collected and treated separately.

3 It has been determined by the European Parliament that there

are potential negative effects on the environment and human

health as a result of the presence of hazardous substances in

electrical and electronic equipment.

4 It is the users’ responsibility to utilize the available collection

system to ensure WEEE is properly treated.

For information about the available collection system, please

contact Extreme Customer Support at 353 61 705500 (Ireland).

Hazardous Substances

This product complies with the requirements of Directive 2011/65/

EU of the European Parliament and of the Council of 8 June 2011

on the restriction of the use of certain hazardous substances in

electrical and electronic equipment.

Declaration of Conformity in Languages of the

European Community

English Hereby, Extreme Networks, declares that this Radio LAN

device is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

Finnish Valmistaja Extreme Networks vakuuttaa täten että Radio

LAN device tyyppinen laite on direktiivin 1999/5/EY

oleellisten vaatimusten ja sitä koskevien direktiivin muiden

ehtojen mukainen.

Dutch Hierbij verklaart Extreme Networks dat het toestel Radio

LAN device in overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn 1999/5/EG.

Bij deze verklaart Extreme Networks dat deze Radio LAN

device voldoet aan de essentiële eisen en aan de overige

relevante bepalingen van Richtlijn 1999/5/EC.

French Par la présente Extreme Networks déclare que l'appareil

Radio LAN device est conforme aux exigences essentielles

et aux autres dispositions pertinentes de la directive 1999/

5/CE.

Par la présente, Extreme Networks déclare que ce Radio

LAN device est conforme aux exigences essentielles et aux

autres dispositions de la directive 1999/5/CE qui lui sont

applicables.

Swedish Härmed intygar Extreme Networks att denna Radio LAN

device står I överensstämmelse med de väsentliga

egenskapskrav och övriga relevanta bestämmelser som

framgår av direktiv 1999/5/EG.

Danish Undertegnede Extreme Networks erklærer herved, at

følgende udstyr Radio LAN device overholder de

væsentlige krav og øvrige relevante krav i direktiv 1999/5/

EF.

German Hiermit erklärt Extreme Networks die Übereinstimmung des

"WLAN Wireless Controller bzw. Access Points" mit den

grundlegenden Anforderungen und den anderen relevanten

Festlegungen der Richtlinie 1999/5/EG.

Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ ΟΤΙ Radio

LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ

Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.

Icelandic Extreme Networks lysir her med yfir að thessi bunadur,

Radio LAN device, uppfyllir allar grunnkrofur, sem gerdar

eru i R&TTE tilskipun ESB nr 1999/5/EC.

Italian Con la presente Extreme Networks dichiara che questo

Radio LAN device è conforme ai requisiti essenziali ed alle

altre disposizioni pertinenti stabilite dalla direttiva 1999/5/

CE.

Spanish Por medio de la presente Extreme Networks declara que el

Radio LAN device cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la

Directiva 1999/5/CE.

Portuguese Extreme Networks declara que este Radio LAN device está

conforme com os requisitos essenciais e outras disposições

da Directiva 1999/5/CE.

Malti Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN

device jikkonforma mal-htigijiet essenzjali u ma

provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/

5/EC.

Extreme Networks

Wireless Access Points

Quick Reference

WS-AP3801i

9034835-02

Andere Extreme Networks Drahtloser Zugangspunkt Handbücher

Extreme Networks

Extreme Networks WS-AP3805 Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 3550 Kurzanleitung

Extreme Networks

Extreme Networks Altitude 4600 Series Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 4511 Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3000X Bedienungsanleitung

Extreme Networks

Extreme Networks AP305C Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3915i-FCC Bedienungsanleitung

Extreme Networks

Extreme Networks AP510C Installationshandbuch

Extreme Networks

Extreme Networks IdentiFi Wireless WS-AP3825i Bedienungsanleitung

Extreme Networks

Extreme Networks AP305C Installationshandbuch

Extreme Networks

Extreme Networks Altitude 4000 Series Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 4511 Merkblatt

Extreme Networks

Extreme Networks Altitude 3500 Series Installations- und Betriebshandbuch

Extreme Networks

Extreme Networks WS-AP3805-FCC/ROW Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP410C-1-WR Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3805i-FCC Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP302W Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3935e Bedienungsanleitung

Extreme Networks

Extreme Networks AP-7602 Service-Handbuch

Extreme Networks

Extreme Networks Altitude 4760 Series Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 4700 Series Installations- und Betriebshandbuch

Extreme Networks

Extreme Networks Altitude 4522 Series Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP560h Bedienungsanleitung

Extreme Networks

Extreme Networks AP-7562 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung