Extron electronics DTP T DWP 4K D Series Bedienungsanleitung

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

DTP T DWP 4K D Series • Setup Guide

This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP T DWP 4K D series of

twisted pair (TP) wallplate extenders.

Installation

Step 1 — Disconnect Power

Disconnect all equipment power sources.

Step 2 — Prepare the Mounting Surface

ATTENTION:

•Installation and service must be performed by

authorized personnel.

•L’installation et l’entretien doivent être effectués par le

personnel autorisé uniquement.

•The unit must be installed in accordance with the

National Electrical Code and with local electrical and

safety codes.

•L’unité doit être installée conformément au National

Electric Code et aux normes électriques et de sécurité

locales.

NOTE: Use a UL-listed junction box with a depth of at least 3.0 inches (7.6 cm). Alternatively, the included mud ring (MR

200) can be used. For more information, see the full product user guide at www.extron.com.

a. Place the junction box against the installation surface and mark the opening guidelines.

TIP: Use a level to mark the opening.

b. Cut out the material from the marked area.

c. Secure the junction box to the wall stud with 10-penny nails, #8 screws, or #10 screws, leaving the front edge ush with the

surface.

d. Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.

TIP: In order to t the unit in the junction box, do not install boots on TP cables and RJ-45 connectors.

Extron

DTP T DWP 4K 332 D

Signal Output

Cable

Clamp

Decorator-Style Faceplate

Screws or

Nails

Wall opening is

ﬂush with edge of box.

Wall Stud

AUTO SW

CONFIG

HDMI IN

AUDIO IN

HDBT

DTP

HDCP

AUDIO IN

DP IN

TLP 1000T

IPCP 505

IN1608

DTP HDMI 230 Rx

Projector

100-240V~ -- A MAX

CONFIGURABLE

HDMI HDMI

RS-232 IR

Tx Rx Tx RxG

Tx Rx Tx RxG Tx Rx Tx RxG

HDMI

INPUTS OUTPUTS

Tx Rx

RS-232

LAN

2x25W(8Ω)/2x50W(4Ω)

RESET

AUDIO INPUTS OUTPUTS

REMOTE

LL1R R

L2 R

CLASS2 WIRING

L4R

L5R

+48V

VARIABLE

IN1608SA

MIC/LINE

L6R

SIG LINK

DTPIN

SIG LINK

DTPIN

SIG LINK

DTPOUT

50/60Hz

RS-232 IR

OVERDTP

AMPLIFIED OUTPUT

VOLUME

SCALINGPRESENTATION SWITCHER

IN1608

INPUTS

HDCP

SIGNAL

OUTPUTS

ENTER

Extron

2 3 4 5 6 7 8 A B C

INPUTS

1 2 3 4 5 6 7 8

CONFIG

Extron

DTP T DWP 4K 232 D Tx

TransmitterEthernet

Network

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

XTP DTP 24 Cable

230'

HDMI

12345678

100

LINK

ACT

COM

IR/S

RTS

CTS

RELAY FLEX

I/O

eBUS

ACTLIMIT

OVER

SWITCHED

12VDC

OVER

LIMIT

IPCP 505

AUDIO IN

DP IN

AUDIO IN

HDMI IN

Extron

DTP T DWP 4K D Series • Setup Guide (Continued)

Step 3 — Connect Inputs to the Extender

Front panel

AAudio input connectors — Connect an unbalanced stereo audio

source to this 3.5 mm mini stereo jack.

BHDMI input connector — Connect an HDMI cable between this port

and the output port of the digital video source.

CDisplayPort input connector — Connect a DisplayPort cable

between this port and the output port of the video source.

DMini USB port — Connect a male USB mini-B cable to this port for

SIS configuration and firmware updates.

Rear panel

ADC power input connector — Wire and plug the included external 12 VDC power supply into either this 2-pole connector or

the power input connector on the receiver (see the DTP T DWP 4K 232/332 D User Guide at

www.extron.com for wiring information).

BOver TP connector — Connect an RS-232 device, IR device, or both to this 5-pole, 3.5 mm captive screw connector for

bidirectional pass-through device control. Wire the connector as shown in the diagram below. The Ground pin is shared by

both devices.

•RS-232 — Connect an RS-232 device and congure it as follows: 9600 baud rate, 8 data bits,1 stop bit, no parity.

•IR — Bidirectional TTL level (0 to 5 V) modulated infrared from 30 kHz to 60 kHz.

CRemote connector — Connect an RS-232 device to this 3-pole, 3.5 mm captive screw connector for SIS configuration and

firmware updates. Wire the cable as shown in the diagram below.

DGround port — Use the included grounding strap to ground the unit to a junction box or other grounding point.

Ground

Transmit pin on connected unit

Receive pin on connected unit

Connected RS-232 and

IR Device Pins

Transmit pin for IR control

Receive pin for IR control

RxTx

RS-232 IR

RxTx

OVER TP

A DC power input connector

B Over TP connector

C Remote connector

D Ground port

E DTP Out connector (page 3)

F Reset button (page 3)

G DTP/HDBaseT switch (page 3)

POWER

12V

1.1 A MAX

DTP T DWP 4K 232 D

RS-232RS-232 SIG LINK

Tx RxTx Rx G Tx Rx G

RESET

OVER TP REMOTE OUT

DTP T DWP 4K D Rear Panel

HDBT

DTP

DTP T DWP 4K D Side Panel

AUDIO IN

AUTO SW

HDCP

CONFIG

HDMI IN

AUDIO IN

DP IN

Extron

DTP T DWP 4K D Front Panel

Tx Rx G

RS-232

Ground

Transmit pin on connected uni

Receive pin on connected unit

E DTP Out connector — Connect one end of a twisted pair cable to this RJ-45 connector and the opposite end to a

compatible receiving device.

ATTENTION:

•Do not connect this output to a telecommunications or computer data network.

•Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.

F Reset button — Use an Extron Tweeker or small screwdriver to press and hold the recessed button while cycling power to

the extender to perform a factory reset.

GDTP/HDBaseT switch — Set this 2-position, recessed switch to configure the output between HDBaseT and DTP modes.

When configured for HDBaseT, use an HDBaseT-compatible receiving device. When configured for DTP, use a DTP-

compatible receiving device.

NOTES:

•When the switch is set to DTP mode, remote power is available and a single power supply connected to either

a extender or compatible receiver can power both units.

•When the switch is set to HDBaseT mode, remote power is disabled and power supplies are required for both

extender and a receiving device. Analog audio is enabled, but incompatible with third-party HDBaseT devices.

Step 4 — Run Cables Between Units

Connect the rear panel extender output to a rear panel receiving device input using twisted pair cable.

Wire the cable as shown in the diagram to the right.

For optimal performance, Extron highly recommends the following:

•RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B wiring

standard for all connections. For more information on TP cable wiring and termination, see the full

product user guides at www.extron.com.

•Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable

bandwidth of 400 MHz.

ATTENTION:

•Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the device with

DTP extenders or receivers.

•N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier

le appareil avec les émetteurs ou les récepteurs DTP.

•Use shielded RJ-45 plugs to terminate the cable.

•Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches used. If

possible, limit the number of patches to two total.

•If RJ-45 patches must be used in the system, shielded patches are recommended.

Step 5 — Connect the Outputs from a Compatible Receiver

a. Connect an HDMI or DisplayPort cable (depending on your receiving device type) between the receiving device output port

and the input port of the display.

b. Connect a stereo audio device to the 3.5 mm mini stereo jack to receive the passed-through unbalanced audio.

c. Plug an RS-232 or modulated IR device into the RS-232/IR pass-through port.

Step 6 — Power the Units

The units can be powered one of two ways:

•Locally with the included power supply. A compatible receiving device can be powered remotely through the DTP line.

•Remotely via the DTP line by a locally powered DTP 230 or 330 compatible device.

NOTE: See notes in Gabove for remote power restrictions.

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA

T568-B

TP Wires

12345678

Pins:

468-2762-50 Rev. B

5 17

Step 7 — Final Installation

a. Make all connections, power the units, and test the system for satisfactory operation.

b. At the power outlet, unplug the power supply.

c. Mount the extender into the wall box, and attach the supplied decorator-style faceplate to the unit.

d. At the power outlet, reconnect the power supply. This powers up both units.

Operation

NOTE: Input switching can be performed via auto switching, RS-232, or IR through the rear panel connectors.

After all devices are powered up, the system is fully operational.

Extender LEDs

ALEDs — These two-color front panel LEDs on the extenders light to indicate signal and power status as follows:

•Amber — The unit is receiving power but there is no signal on the associated input.

•Green — The unit is receiving power and a signal is present on the associated input.

BSwitch LED — Lights green when auto switch is active.

CLEDs — Light green when an HDMI or DisplayPort input has been authenticated on the source device.

Audio Conﬁguration

The DTP T DWP 4K D series can embed analog audio inputs onto the digital video output.

NOTE: If no HDMI or DisplayPort signal is present, analog audio transmitted over the DTP connection to the analog audio

output of the receiver.

When an input is selected, audio transport over HDMI or DisplayPort can be congured to operate in one of three modes. Each

input can be congured individually for any of the three modes.

•Transport digital embedded audio (default) — The digital embedded audio content on the digital video input is transported.

Analog audio is still separate from the digital embedded audio on the HDMI or DisplayPort signal and transported

simultaneously over the DTP output, not embedded onto the digital output.

•Embed analog audio input — The analog audio input is always embedded to the digital output, replacing whatever content

is already present on the digital embedded audio. Analog audio is also transported over the DTP output as a simultaneous

output.

•Auto select between analog audio and digital embedded audio — When both analog audio and digital embedded audio

on HDMI or DisplayPort are present, digital embedded audio on the HDMI or DisplayPort signal takes priority. Analog audio is

transported simultaneously with the digital embedded audio content that is already present on the DTP output.

AUDIO IN

AUTO SW

HDCP

CONFIG

HDMI IN

AUDIO IN

DP IN

Extron

DTP T DWP 4K D Front Panel

Inhaltsverzeichnis

Andere Extron electronics Extender Handbücher

Extron electronics

Extron electronics FOX T UWP 302 Bedienungsanleitung

Extron electronics

Extron electronics DTP R HWP 4K D series Bedienungsanleitung

Extron electronics

Extron electronics eLink 100 Bedienungsanleitung

Extron electronics

Extron electronics CSVEQ 100 D Bedienungsanleitung

Extron electronics

Extron electronics FOX 3G HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX Tx HDMI Bedienungsanleitung

Extron electronics

Extron electronics USB Extender Plus T Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 330 Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 301 Bedienungsanleitung

Extron electronics

Extron electronics FOX 2G Tx AV Bedienungsanleitung

Extron electronics

Extron electronics DTP T/R DP 330 Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 230 Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX Tx HDMI Bedienungsanleitung

Extron electronics

Extron electronics FOX 500 DVI Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Rx DVI Bedienungsanleitung

Extron electronics

Extron electronics HFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics DTP T 3G-SDI 230 Bedienungsanleitung

Extron electronics

Extron electronics DTP T DWP 4K 232 D Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX Tx DVI Plus Bedienungsanleitung

Extron electronics

Extron electronics HDMI 230 D Bedienungsanleitung

Extron electronics

Extron electronics XTP R HWP 201 Bedienungsanleitung

Extron electronics

Extron electronics TP Series Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 301 Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 4K 330 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung