Extron electronics SW HD 4K PLUS Series Bedienungsanleitung

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DXP 42 HD 4K PLUS • Setup Guide

The DXP 42 HD 4K PLUS is a four input, two output HDMI matrix switcher that routes HDMI signals from multiple sources to

HDMI-equipped display devices. It supports computer and video resolutions up to 4K @ 60 Hz. It also supports HDMI 1.nand

2.0b specications, including data rates up to 18.2 Gbps, HDR Deep Color up to 12-bit, 3D, and HD lossless audio formats. The

switcher is HDCP 2.2 and 1.4 compliant, and incorporates Extron technologies including SpeedSwitch®, EDID Minder®, and Key

Minder®. Digital audio can be de-embedded from any input and assigned to independent analog stereo outputs.

This setup guide enables you to quickly set up and congure your DXP 42 matrix switcher. Step-by-step instructions show

you how to connect the hardware and to perform basic operations using both the front panel controls and selected Simple

Instruction Set (SIS) commands. The guide also shows you how to connect to the built-in web page and load and start up the

Product Conguration Software (PCS), which you can also use to congure and operate the switcher. For additional information

and specications, see the DXP HD 4K PLUS product page at www.extron.com.

The terms “DXP,” “DXP 42”, “matrix,” “switcher,” and “DXP 42 matrix switcher” are used interchangeably in this guide to refer to

the DXP 42 HD 4K PLUS.

LAN

POWER

12V

1.5A MAX

INPUTS

HDMI

OUTPUTS

HDMI/CEC

AUDIO OUTPUTS

L3R L 4R

RS-232

Rx G

REMOTE

MODEL80

FLATPA NEL

ShareLink Pro 1000

HD WIN

STANDBY

SCREEN DECODER

HD PASS

HDMI DECODER

SIGNAL

HDCP

CONFIG

OUTPUTINPUT

HDMI

WINDOW

HDMI

PASS-THROUGH

USB

WiFi 1234

LANPOWER

12V

1A MAX

Tx Rx RTSCTS

COM 1

Tx Rx

COM 2

VCG

VOL RELAYS

12C

1 2 3 4G

DIGITAL I/O

PWR OUT =6W

eBUS

+V +S -S G

LAN

IPCP PRO250

IR/S

Laptop

Tablet

Smartphone

Wireless Access Point

Videoconferencing PC

Logitech

Rally Mic Pod

4K Display

Logitech

Rally Camera

USB

Ethernet

RS-232

Ethernet

Ethernet AudioAudio

HDMI

HDMIHDMI

HDMI

HDMIHDMI

Extron

TLP Pro 1025T

10" Tabletop TouchLink

Pro Touchpanel

Extron

IPCP Pro 250

IP Link Pro

Control Processo

Extron

SB 33 A

Sound Bar

Ext

ron

ShareL

ink Pro 1000

Wireless

and Wired

Collaboratio

n Gateway

Extron

DXP 42 HD 4K PLUS

4K/60 HDMI Matrix

Switcher with Audio

De-Embedding

Laptop Laptop

USBUSB

HDMI

Capture

Ethernet

Figure 1. Typical Application of the DXP 42 HD 4K PLUS

Setup Steps

Follow these steps to set up and start operating the DXP 42 matrix switcher:

1. Turn off power to the input and output devices that will be connected.

2. Connect HDMI input devices to the rear panel input connectors (see figure 2, A, on the next page).

3. Connect HDMI audio and video output devices to the rear panel output connectors: video (B), audio (C), or both.

4. Connect control devices as desired:

• Connect a computer or control system to the Remote RS-232 (D) or the front panel USB Config port (see figure 5, C,

on page 4).

• Connect a computer, control system, or network switch to the RJ-45 LAN (Ethernet) port (see figure 2, E).

5. Connect the provided 12 V, 1.5 A power supply between the DXP switcher and a 100-240 VAC, 50-60 Hz power source, and

connect power to the input and output devices.

6. Download the PCS program from www.extron.com (see Downloading the Software on page 10).

DXP 42 HD 4K PLUS Series • Setup Guide (Continued)

7. Select EDID files to apply to inputs as desired, using PCS (see the DXP HD 4K PLUS Series Help file for details).

8. Create ties as desired (see Creating Ties on page 5).

Rear Panel Connections

CAUTION: Remove power from the system before making any connections.

ATTENTION : Couper l’alimentation avant de faire l’installation électrique.

ATTENTION:

• Use electrostatic discharge precautions (be electrically grounded) when making connections. Electrostatic discharge

(ESD) can damage equipment, although you may not feel, see, or hear it.

• Prenez des précautions contre les décharges électrostatiques (soyez électriquement relié à la terre) lorsque vous

effectuez des connexions. Les décharges électrostatiques (ESD) peuvent endommager l’équipement, même si vous ne

pouvez pas le sentir, le voir ou l’entendre.

LAN

POWER

12V

1.5A MAX

INPUTS

HDMI

OUTPUTS

HDMI/CEC

AUDIO OUTPUTS

L3R L 4R

RS-232

Rx G

REMOTE

FFF

AAD

AInput connectors C Analog audio outputs ELAN port

BOutput connectors D Remote RS-232 connector F Power connector

Figure 2. DXP 42 HD 4K PLUS Rear Panel

AInput connectors — Connect HDMI (or DVI with an appropriate adapter) sources to these female 19-pin type A

HDMI connectors for video input.

LockIt™ cable lacing brackets, one for each HDMI input and output connector, are provided with the DXP 42 HD 4K PLUS.

These brackets can be used to secure the HDMI cables to the DXP connectors to reduce stress on the HDMI connectors

and prevent signal loss due to loose cable connections (see Securing HDMI Cables with the LockIt HDMI Cable Lacing

Bracket on page 4).

BVideo output connectors — Connect HDMI (or DVI with an appropriate adapter) displays or other output devices

to these female 19-pin type A HDMI output connectors for buffered video output (see Securing HDMI Cables with

the LockIt HDMI Cable Lacing Bracket).

C Analog audio outputs — Connect powered speakers, an amplifier, or other audio output device to these 5-pole 3.5 mm

captive screw connectors for 2-ch stereo analog audio output. These connectors can provide de-embedded LPCM audio

that was routed from any DXP HDMI input and convert it to a stereo analog signal. Figure 3 shows how to wire these

connectors. Use the supplied tie-wrap to strap the audio cable to the extended tail of the connector.

Do not tin the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Figure 3. Connecting Analog Audio

ATTENTION:

• For unbalanced audio output, connect the sleeves to the ground contact. DO NOT connect the sleeves to the

negative (-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux

contacts négatifs (–).

NOTE: The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

DRemote RS-232 connector — Connect an RS-232 capable host

device such as a computer or a touch panel control to this 3.5 mm

3-pole captive screw connector to configure and control the

switcher via SIS commands. Connect the 9-pin end of the RS-232

cable to the serial port of your computer or control system (see the

diagram at right). The default port parameters are 9600 baud, 8 data

bits, 1 stop bit, no parity.

ELAN port — Connect a computer, a network switch, or a control

system to this RJ-45 connector (see figure 4 for wiring information).

With the Ethernet connection, you can use a computer to configure

and control the networked switcher with SIS commands, the PCS

configuration program, or the embedded HTML page.

Ethernet connection indicators — The Link and Act

LEDs indicate the status of the Ethernet connection.

• Link — Indicates that the switcher is properly connected to an

Ethernet LAN. This green LED should light steadily.

• Act (Activity) — Indicates transmission of data on the RJ-45

connector. This amber LED should flicker as the switcher

communicates.

Ethernet links use Category (CAT) 3, 5e, or 6 unshielded twisted

pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to 328 feet

(100 meters).

NOTES:

• Do not use standard telephone cables. Telephone cables do not support Ethernet or Fast Ethernet.

• Do not stretch or bend the cables because this can cause transmission errors.

A cable that is wired as T568A at one end

and T568B at the other (Tx and Rx pairs

reversed) is a "crossover" cable.

A cable that is wired the same at both ends

is called a "straight-through" cable because

no pin or pair assignments are swapped.

Both ends of the cable can be T568B (as shown)

or T568A (not shown).

RJ-45

Connector

Insert T

wisted

Pair Wires

12345678

Pins: Crossover Cable Straight-through Cable

Wire Color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire Color

T568A T568B

End 1 End 2 End 1 End 2

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

Wire Color

Blue

White-blue

White-brown

Brown

Wire Color

T568B

White-orangeWhite-orange

OrangeOrange

White-greenWhite-green

Blue

White-blue

GreenGreen

White-brown

Brown

Figure 4. RJ-45 Connector and Pinout Tables

The cable you use depends on your network speed. The switcher supports both 10 Mbps (10Base-T — Ethernet) and

100 Mbps (100Base-T — Fast Ethernet), half-duplex and full-duplex Ethernet connections.

• 10Base-T Ethernet requires CAT 3 or higher UTP or STP cables.

• Fast Ethernet requires CAT 5e or higher UTP or STP cables.

Terminate the Ethernet cable as required:

• Network connection — Wire as a patch (straight-through) cable.

• Computer or control system connection — Wire as a crossover cable.

FPower connector — Plug the provided external

12 VDC, 1.5 A power supply into this 2-pole, 3.5 mm

captive screw connector and into an AC power outlet

(see the diagram at right for wiring).

Computer or

Control System

RS-232 Port

DXP 42 HD 4K PLUS

Rear Panel

RS-232 Port

NOTES:

•If you use cable that has a drain wire, tie

the drain wire to ground at both ends.

•Connect a ground wire between the DXP

and the computer or control system.

Tx Rx G

Ground (G)

Transmit (Tx)

Receive (Rx) Transmit (Tx)

Receive (Rx)

Default Ethernet settings:

• IP address — 192.168.254.254

• Subnet mask — 255.255.0.0

• Gateway address — 0.0.0.0

SECTION A–A

Ridges

Smooth

3/16"

(5 mm) Max.

POWER

12V

1.5 A MAX

DXP 42 HD 4K PLUS Series • Setup Guide (Continued)

Securing HDMI Cables with the LockIt HDMI Cable Lacing Bracket

Use a LockIt HDMI Cable Lacing Bracket to securely fasten each HDMI cable to the switcher:

1. Plug the HDMI cable into the panel connection (see the illustration at right, 1).

2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt

lacing bracket to be placed over it (2). The screw does not have to be removed.

3. Place the LockIt lacing bracket (3) on the screw and against the HDMI connector, then

tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield it fastens to

is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel

elle est attachée est très fin et peut facilement être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown (4).

5. While holding the connector securely against the lacing bracket, use pliers or similar tool to tighten the tie wrap, then remove

any excess length.

Front Panel Features

The front panel buttons have primary and secondary functions. The table on the next page contains descriptions of some of the

basic functions. For more details, see the DXP HD 4K PLUS Series User Guide, available at www.extron.com. Each button has

an LED beside it. These bicolor LEDs light green when video is selected and red when audio is selected.

CONFIG

DXP 42 HD 4K PLUS

INPUTS INPUTS

OUTPUTS

SIGNAL

HDCP

1 2 1 2 1234

3 4

GGG

APower and Reset LED C Config port EOutput buttons GHDCP LEDs

BReset button D Input buttons FSignal LEDs

Figure 5. DXP 42 HD 4K PLUS Front Panel

APower and Reset LED — This green LED lights steadily while the switcher has power.

In addition, while you are holding the Reset button, the LED blinks every 3 seconds to indicate the level of reset that will

occur if the button is released at that point.

BReset button — This recessed button initiates four levels (modes) of reset. Use a pointed object such as a small

screwdriver to press and hold the Reset button.

• Factory firmware reset (mode 1) — Hold the Reset button while powering up the switcher to restore the DXP to

the factory firmware for a single power cycle. This type of reset maintains all the current user settings, such as audio

adjustments, IP settings, and the configuration.

• IP settings reset (mode 4) — While the DXP is running, press and hold the Reset button until the LED blinks twice

(approximately 6 seconds). Release the button and press it again momentarily to reset the switcher IP settings.

• Absolute reset (mode 5) — While the DXP is running, press and hold the Reset button until the LED blinks three

times (approximately 9 seconds). Release the button and press it again momentarily to restore the switcher to the

default factory conditions. This reset, equivalent to the EZQQQ }SIS command, removes the initial serial number

passwords that are set at the factory and resets them to no password.

NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number.

In the event of a complete system reset (Mode 5), the passwords convert to the default, which is no password.

RESET

CConfig port — This USB mini-B port serves a similar communications function to the rear panel Remote RS-232 port, but is

easier to access than the rear port after the matrix switcher has been installed and cabled. Use a USB type A to mini B cable

to connect this port to a USB connector on the computer to enable SIS commands to be sent from the computer, connection

to the PCS configuration software, and uploading firmware.

Front Panel Button Functions

Primary Function Secondary Functions

DInput buttons Select inputs. View ties.

E Output buttons Select outputs. View ties.

FSignal LEDs — The DXP has a green Signal LED for each input. Each LED lights when a signal (TMDS clock activity) is

present on the input.

GHDCP LEDs — The DXP has a green HDCP LED for each input. Each of these LEDs lights if the source connected to its

input is HDCP encrypted.

Operation

Creating Ties

A tie is an input-to-output connection. Ties can be made using the front panel buttons, SIS commands, or PCS. You can tie an

input to one or more outputs.

NOTES:

• A "Set of ties" is an input tied to two or more outputs. (An output can never be tied to more than one input.)

• A "Configuration" is one or more ties, one or more sets of ties, or a combination.

• Audio ties can be made only with de-embedded audio.

• Audio ties cannot be made using the front panel buttons. However, they can be created using PCS or SIS commands.

To make ties:

1. Press an input button on the front panel (see the illustration at right). The LED next to it lights.

• If the selected input is already tied to one or more outputs, the tied output LEDs light.

• If you press the tied output button, the output is disconnected (untied) from the input.

2. Within 5 seconds, press the output button or buttons to which the

input is to be tied. All selected output LEDs light, then turn off after 5

seconds. The illustration at right shows a tie between input 1 and

output 1.

NOTE: If no output is selected within 5 seconds, the input LED

turns off and no tie is made to the input.

To break existing ties:

1. Press the button for the input to be untied. The LEDs for the tied outputs light.

2. Press the output button to be untied. The output button LED turns off, indicating that the tie is broken.

Viewing Ties

• To view ties to an input: Press the desired input button.

The button LEDs light for all outputs that are tied to that input.

The illustration at right shows a tie between input 1 and

output 1. Pressing the input 1 button causes its LED to light.

The output 1 button LED also lights, indicating that a tie exists

between input 1 and output 1.

• To view ties to an output: Press the desired output button.

The LED for the selected output button lights. In addition, the

button LEDs for the tied input and for all outputs tied to that

input light.

The LED lights to

indicate the selection.

The input LED lights to

indicate the selected input.

The output LED lights to

indicate the output is tied to

the selected input.

After 5 seconds, all LEDs turn off.

Input Output

INPUTS OUTPUTS

1 2 1 23 4

Press an output button.

The output button LED lights.

The tied input button LED lights.

DXP 42 HD 4K PLUS Series • Setup Guide (Continued)

Locking and Unlocking the Front Panel (Executive Mode)

Lock mode (executive mode) limits control of the DXP 42 from the front panel, so that functions such as input switching and

output muting are not allowed from the front panel. The executive mode selection remains in effect after a power cycle.

The matrix switcher front panel buttons can be locked and unlocked using the following SIS commands (see the Front Panel

Lock (Executive) Modes commands on page 8 for information on issuing SIS commands to the unit):

• To lock the front panel buttons, enter 1X.

• To unlock the front panel, enter 0X.

Remote Conﬁguration and Control

You can send SIS commands over an Ethernet link (rear panel RJ-45 LAN port, see ﬁgure 2, E, on page 2), a serial connection

(rear panel Remote RS-232 port, D), or USB (front panel Cong port, see ﬁgure 5, C, on page 4). The network connection

procedure is described below. For information about the serial and USB connections, as well as a complete list of the available

SIS commands, see the DXP HD 4K PLUS Series User Guide, available at www.extron.com.

Establishing a Network (Ethernet) Connection

To establish a network connection:

1. Open a TCP socket to port 23 using the switcher IP address.

NOTE: The factory default IP address is 192.168.254.254. You can change this address using SIS commands,

the PCS configuration software, or the internal web page (see the DXP 42 HD 4K PLUS User Guide, available at

www.extron.com, for instructions).

The switcher responds with a message consisting of the copyright date, the name of the product, rmware version, part

number, and the current date and time. For example, with an internet connection:

Ddd,DD Mmm YYYY HH:MM:SS ]

NOTES:

• If the switcher is not password-protected, the device is now ready to accept SIS commands.

• If the switcher is password-protected, a password prompt appears.

2. If the switcher is password-protected, enter the password.

NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number. In

the event of a complete system reset (Mode 5), the passwords convert to the default, which is no password.

3. If the password is accepted, the switcher responds with Login User or Login Administrator.

4. If the password is not accepted, the Password prompt reappears (see your network admin for the assigned password).

Connection timeouts

The Ethernet link times out and disconnects after a designated period of no communications. By default, this timeout value is set

to 5 minutes but the value can be changed.

NOTE: Extron recommends leaving the default timeout at 5 minutes and periodically issuing the Query (Q) command to keep

the connection active or disconnecting the socket and reopening the connection when necessary.

Number of connections

A switcher can have up to 200 simultaneous TCP connections, including all HTTP sockets and Telnet connections. When

the connection limit is reached, the switcher accepts no new connections until some have been closed. No error message or

indication is given that the connection limit has been reached. To maximize performance of your switcher, keep the number of

connections low and close unnecessary open sockets.

SIS Commands

The switchers have SIS commands that you can use for operation and conguration. You can issue these commands from a

PC or control system connected to the DXP serial port, USB port, or Ethernet port (see Rear Panel Connections on page 2 for

connection information).

Host-to-switcher instructions

The switcher accepts SIS commands through the LAN port, the Remote (RS-232) port, or the front panel USB Cong port. SIS

commands consist of one or more characters per command eld. They do not require any special characters to begin or end

the command character sequence. Each switcher response to an SIS command ends with a carriage return and a line feed

(CR/LF = ]), which signals the end of the response character string. A string is one or more characters.

NOTE: Input and output numbers in commands can be entered as one-digit, two-digit, or three-digit numbers. All input and

output numbers are reported as two-digit numbers in the response.

Verbose mode

Telnet connections to a switcher can be used to monitor for changes that occur on the switcher, such as front panel operations

and SIS commands from other Telnet sockets or a serial port. For a Telnet session to receive change notices from the switcher,

the Telnet session must be in verbose mode 1 or 3 (see the Set verbose mode command on page 9).

NOTE: If tagged responses is enabled (modes 2 and 3), all view commands return the same constant string and the value

as the set command does (for example, the view matrix name command ECN}, returns Ipn • X3) ]).

Symbol definitions

]= Carriage return and line feed }or |= Carriage return (no line feed)

• = Space Eor W= <Escape> key

X! = Input number 0through 4(0= untied)

X@ = Output number 0through 2(0= untied)

If the audio output number entered is greater than 4, an E12 error code

(Invalid output number) is returned.

X# = On or off (enable or disable) 0= Off or disable, 1= on or enable

X% = Analog audio output number 3or 4.

X* = Output format 0= Auto (default) 4= HDMI YUV 4:4:4 Full

1= DVI RGB 4:4:4 Full 5= HDMI YUV 4:4:4 Limited

2= HDMI RGB 4:4:4 Full 6= HDMI YUV 4:2:2 Full

3= HDMI RGB 4:4:4 Limited 7= HDMI YUV 4:2:2 Limited

X1@ = Video and sync mute status 0= Video and sync unmuted

1= Video muted

2= Video and sync muted

X1# = Audio mute status 0= Audio unmuted

1= HDMI audio muted

2 = Analog audio muted

3 = HDMI and analog audio muted

X2) = Front panel lock mode status 0= Lock mode 0: Front panel unlocked (default)

(executive mode) 1= Lock mode 1: Front panel locked

X2# = Verbose mode 0= Clear or none (default for Telnet connection)

1=Verbose mode (default for RS-232 and USB connections)

2= Tagged responses for queries

3= Verbose mode and tagged responses for queries

X2% = Firmware version (n.nn) Shown to second decimal place

X2^ = Firmware and build version Example: 1.00.0000-b003

X3) = IP address nnn.nnn.nnn.nnn

X3! = Subnet mask nnn.nnn.nnn.nnn

X3@ = Gateway address nnn.nnn.nnn.nnn

X3% = Port timeout 1to 65000 in 10-second intervals (30 = default)

NOTES:

• Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*8$.

• The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!,02*02&, or 003*003%).

DXP 42 HD 4K PLUS Series • Setup Guide (Continued)

Command and Response Table for SIS Commands

Command Function ASCII Command

(Host to Switcher)

Response

(Switcher to Host) Additional Description

Output Switching (Ties)

Tie HDMI input to HDMI output (video

and audio).

X!*X@! OutX@•InX!•All]Tie HDMI input X! to HDMI output X@,

video and audio.

Example 1*2! Out2•In1•All]Tie input 1 to output 2, video and audio.

Tie an input to all outputs, audio and

video

X!*! InX!•All]Tie input X! to all outputs, audio and

video.

Video Mutes

Set video mute for an output X@*X1@B VmtX@*X1@] Set video mute on output X@ to X1@.

Set video mute for all outputs X1@*B Vmt X1@] Set video mute on all outputs to X1@.

View video mute status for an output X@BX1@] View mute status X1@ for output X@.

Unmute video and sync for an output X@*0B VmtX@*0]Unmute video and sync on output X@.

Unmute video for all outputs 0*B Vmt0]Unmute HDMI video on all outputs.

Audio Mutes

NOTE: Audio mute commands affect both HDMI and analog audio, depending on the output from which the audio was

de-embedded.

Mute audio on an output X@*X1#Z AmtX@*X1#] Set audio mute for output X@ to X1#.

Mute all audio X1#*Z AmtX1#] Set audio mute for all outputs to X1#.

View audio mute status of an output X@*Z X1#] View mute status X1# for output X@.

Unmute audio on an output X@*0Z AmtX@*0]Unmute audio for output X@.

Unmute all audio 0*Z Amt0]Unmute audio for all outputs.

Front Panel Lock (Executive) Modes

NOTE: See Locking and Unlocking the Front Panel (Executive Mode) on page 6 for more information on the lock modes.

Set front panel lock mode X2)X ExeX2)] Set the front panel lock mode to X2).

View lock status XX2)] Display current lock mode X2).

KEY: X! = Input number

0through 4(0= untied)

X@ = Output number 1or 2(0= untied). If the audio output number entered is greater than 2, an

E12 error code (Invalid output number) is returned.

X1@ = Video mute status 0= video and sync unmuted, 1= HDMI video muted,

2= video and sync muted,

3= HDMI and analog audio muted

X1# = Audio mute status 0= audio unmuted, 1= HDMI audio muted, 2= analog audio muted,

3= HDMI and analog audio muted

X2) = Front panel lock mode 0= unlocked (default), 1= locked

Information Requests

General information request IV04X02•A04X02]Show the number of video and audio

inputs (04) and outputs (02).

On the DXP 42 HD 4K PLUS, the matrix

is four video and audio inputs by two

video and audio outputs (outputs 3 and

4 are de-embedded analog audio only

outputs).

Query part number N60-1678-01]In verbose modes 2 and 3:

Pno60-1678-01

Command Function ASCII Command

(Host to Switcher)

Response

(Switcher to Host) Additional Description

Information Requests (continued)

Query rmware version QX2%] View the unit rmware version to the

second decimal place.

In verbose modes 2 and 3:

Ver01*X2%

Query rmware and build version *Q X2^] View unit rmware version and build

number X2^.

In verbose modes 2 and 3:

Bld01*X2^

IP Setup

Set IP address EX3)CI}IpiX3)] Set the unit IP address to X3).

View IP address ECI} X3)] View unit IP address.

Set subnet mask EX3!CS}IpsX3!] Set the subnet mask for the unit to X3!.

View subnet mask ECS} X3&] View the subnet mask.

Set gateway IP address EX3@CG}IpgX3@] Set the unit gateway address to X3@.

View gateway IP address ECG} X3@] View the unit gateway address.

Set DHCP on and off EX#DH}IdhX#] Set DHCP to X#.

View DHCP on/off status EDH}X#]View the DHCP setting.

Congure current port timeout E0*X5*TC}Pti0*X5*] Set the current port timeout to X5*.

Read current port timeout E0TC} X5*] View the current port timeout setting.

Congure global IP port timeout E1*X5*TC}Pti1*X5*] Set the global IP port timeout to X5*.

Read global IP port timeout E1TC} X5*] View the global IP port timeout setting.

Set verbose mode EX5#CV}VrbX5#] Set the verbose mode and tagged

responses to X5#.

Read verbose mode ECV} X5#] View the current verbose mode.

KEY:

X# = On or off (enable or disable) 0= DHCP disabled (default), 1= DHCP enabled

X2% = Firmware version number Expressed to the second decimal place (n.nn)

X2^ = Firmware version and build number n.nn.nnnn

X3) = IP address nnn.nnn.nnn.nnn (Default = 192.168.254.254)

X3! = Subnet mask nnn.nnn.nnn.nnn (Default = 255.255.0.0)

X3@ = Gateway IP address nnn.nnn.nnn.nnn (Default = 0.0.0.0)

X5# = Verbose mode 0= clear or none (default for Telnet connection)

1= verbose mode (default for RS-232 and USB connection)

2= tagged responses for queries

3= verbose mode and tagged for queries

X5* = Port timeout interval 1(10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)

Reset

System reset to factory defaults EZXXX}Zpx]Clear all ties and presets and reset unit

to factory default settings.

NOTE: This command excludes IP settings such as IP address and subnet mask. It does not remove the file system.

Absolute system reset EZQQQ}Zpq]Clear all ties and reset unit to factory

default settings.

NOTES:

• This command includes resetting the IP address to 192.168.254.254 and the subnet mask to 255.255.0.0. The firmware

version remains the same.

• The factory configured passwords for all accounts on this device have been set to the device serial number. Passwords are

case sensitive. In the event of an absolute system reset, the passwords convert to the default, which is no password.

DXP 42 HD 4K PLUS Series • Setup Guide (Continued)

Installing and Starting the Conﬁguration Software

The Extron Product Conguration Software (PCS) is a Windows-based program for the DXP 42 HD 4K PLUS that enables you to

congure the input and output, audio, and image settings. It also lets you save and recall presets, select EDID, and perform nearly

all the other functions that can be accomplished via the front panel controls or SIS commands.

NOTE: EDID selection is available only through PCS. When the DXP is connected to PCS, the power save mode is reset to 0

(power save off).

Downloading the Software

To use PCS, download the program from www.extron.com and install it on the PC that will be connected to the DXP:

1. Open the Extron web page and select the Download tab (see figure 6, 1).

Figure 6. Software Link on the Download Tab

2. Move the mouse pointer to the Software link (2) in the Downloads column and click it.

3. On the Download Center Software page, click the P(see figure 7, 1).

Figure 7. PCS Download Link

4. On the Login page, enter the requested information. If you need an ID number, contact your Extron representative.

5. Follow the instructions on the subsequent screens to download the program. By default the installation creates a folder called

“Extron PCS” at c:\Program Files (x86)\Extron\Extron PCS or c:\Program Files\Extron\Extron PCS. If there is not

already an Extron folder in your Program Files x86 folder, the installation program creates it.

Starting the configuration program

1. Connect the DXP 42 HD 4K PLUS to your computer via USB (front panel Config port) or TCP/IP (rear panel LAN port).

Andere Handbücher für SW HD 4K PLUS Series

Inhaltsverzeichnis

Andere Extron electronics Matrix-Umschalter Handbücher

Extron electronics

Extron electronics DXP HD 4K Series Bedienungsanleitung

Extron electronics

Extron electronics MVX Plus 128 VGA A Bedienungsanleitung

Extron electronics

Extron electronics MultiMatrix SMX System Bedienungsanleitung

Extron electronics

Extron electronics Matrix 50 Series Bedienungsanleitung

Extron electronics

Extron electronics SMX Series Bedienungsanleitung

Extron electronics

Extron electronics MVX 128 VGA A Bedienungsanleitung

Extron electronics

Extron electronics MAV Plus Bedienungsanleitung

Extron electronics

Extron electronics MPX 423 A Bedienungsanleitung

Extron electronics

Extron electronics MVX 128 VGA A Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 300 84 Bedienungsanleitung

Extron electronics

Extron electronics FOX3 Matrix Series Bedienungsanleitung

Extron electronics

Extron electronics MAV 44 Series Bedienungsanleitung

Extron electronics

Extron electronics DXP 1616 HD 4K PLUS Series Bedienungsanleitung

Extron electronics

Extron electronics DXP DVI Pro Bedienungsanleitung

Extron electronics

Extron electronics DXP HD 4K Series Bedienungsanleitung

Extron electronics

Extron electronics ISM 182 Bedienungsanleitung

Extron electronics

Extron electronics MPX Plus 866 A Bedienungsanleitung

Extron electronics

Extron electronics DXP 44 4K PLUS Bedienungsanleitung

Extron electronics

Extron electronics MVX Series Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 42 HVA Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 300 Series Bedienungsanleitung

Extron electronics

Extron electronics Matrix 50 Series Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Bedienungsanleitung

Extron electronics

Extron electronics FOX3 Matrix 80x Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte