Extron electronics NAV SD 511 Bedienungsanleitung

IMPORTANT:

Go to www.extron.com for the

product specifications.

NAV SD 511 • Setup Guide

CLASS 1 LASER PRODUCT, see NAV SD 511 User Guide at www.extron.com

WARNING: The NAV SD 511 output continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.

• Do not look into the ber optic cable connectors or into the ber optic cables themselves.

• Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.

AVERTISSEMENT : Le NAV SD 511 émettent une lumière invisible en continu (équipement de classe 1) qui peut être dangereuse

pour les yeux ; à utiliser avec précaution.

• Ne pas xer directement les connecteurs optiques ou les câbles bre optique.

• Associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble bre optique est débranché.

This guide provides instructions for an experienced installer to install the Extron NAV SD 511 scaling decoders and to make all

connections. One or more compatible Extron NAV encoders and one or more decoders form an AV distribution and switching matrix on a

managed 1G IP network.

NOTE:For more information on any subject in this guide, see the NAV SD 511 User Guide, available at www.extron.com.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the decoder as required.

Step 2 — Rear Panel Connections

HDMI

POWER

12V

2.0 A MAX L

Tx Rx GSG

RS-232 IRR

AUDIO

CONTROLOUTPUT

NAV SD 511

RESET

5V/200 mA

USB 2.0

NAV 1G EXT

LAN

FFFBBB

DDD

CCCHHHEEEGGGAAA

Figure 1. NAV SD 511 Rear Panel Features

ANAV 1G port — Use a pair of fiber cables to connect to a LAN on which one or more encoders also reside for streaming and control.

NOTE: Ensure that you use the proper ber cable for your decoder. Typically, singlemode ber has a yellow jacket

and multimode cable has an orange or aqua jacket.

BExtension port — If desired, connect another networked device to this port. The port acts as a networked 1G switch to the NAV 1G

port.

CHDMI output port — Connect an HDMI cable between this port and an HDMI display (or a DVI display, with an appropriate adapter).

See LockIt®Lacing Brackets on page 6 to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the decoder.

DAudio output port — This 5-pole, 3.5 mm captive screw connector outputs the streamed, unamplified, line level analog audio. Connect

an audio device, such as an audio amplifier or powered speakers (see Analog audio output connector on page 6 to wire the

connector).

EControl RS-232/IR port — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw

connector for bidirectional RS-232 and IR communication with connected remote controlled devices using an Extron control system

(see Control connector on page 6 to wire the connector).

FUSB 2.0 port — Connect a USB Type-C cable to USB host or a USB device. See LockIt®Lacing Brackets on page 6 to securely

fasten the USB connector to the decoder.

NOTE: This connector is limited to supplying 200 mA in USB device mode.

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

GReset button (see figure 1 on page 1)— This button initiates three modes of reset (see the NAV SD 511 User Guide, available at

www.extron.com, for details).

HPower connector — Plug the included external 12 VDC power supply into this 2-pole connector (see Power connector on page6 to

wire the connector).

Step 3 — Front Panel Configuration Port Connection

NAV SD 511

NAV

HDCP

VIDEO

CONFIG

ANALOG

HDMI

ACTIVE

HOST -LNK-

-ACT-

NAVEXT

USB

AUDIO

AUDIO LAN IDUSB

EEECCC

AAABBBDDDEEEFFF

Figure 2. NAV SD 511 Front Panel Features

AConfiguration port — Connect a PC to the decoder via this front panel mini-USB connector for configuration of the unit. The port

uses IP over USB technology; the IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also discoverable

via Toolbelt (see the NAV SD 511 User Guide). The guide and Toolbelt are available for download at www.extron.com).

Indicators

BPower LED — Indicates power and startup status, as follows:

• Blinking — The unit is receiving power and is booting up.

• Lit steadily — The unit is receiving power and is operational.

CNAV LEDs — Indicates status of the streaming input, as follows:

• VIDEO — Indicates status of the video stream.

• Lit steadily — The decoder is receiving a video stream.

• Blinking — A video stream is being decoded, but network errors are present that affect the video quality.

• HDCP — The video stream is HDCP encrypted.

• AUDIO LED — Indicates status of the audio stream.

• Lit steadily — The decoder is receiving an audio stream.

• Blinking — An audio stream is being decoded, but network errors are present that affect the audio quality.

• USB LED — Indicates status of the USB stream.

• Lit Steadily - The decoder is actively receiving and sending a NAV USB stream.

• Unlit — The decoder is not actively sending and receiving a NAV USB stream.

• Blinking - The decoder is unable to establish a NAV USB stream.

DAudio LEDs — Indicate the active audio output, as follows:

• HDMI — The embedded HDMI audio output is selected.

• ANALOG — The analog audio output is selected.

EUSB LEDs — Indicates the status of the USB stream, as follows:

• Host

• Lit steadily – The decoder is in USB host mode.

• Unlit – The decoder is in USB device mode, the default condition.

• Active

• Lit steadily – A USB device or host is connected to the rear panel USB port.

• Unlit – No host or USB device is connected to the rear panel USB port.

• Blinking – A USB device or hub is connected to the decoder and is attempting to draw more power than the USB port can

supply.

NAV SD 511 • Setup Guide (Continued)

FLAN LEDs (see figure 2 on page 2) — Indicate the status of the network connections, as follows:

• NAV LED —

• Link LED — Lit steadily indicates that a network link is established at 1G.

• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.

• Ext LED —

• Link LED — Lit steadily indicates that a network link is established at 1G. Blinking indicates a link speed less than 1Gbps.

• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.

GID button and LED — The recessed ID button identifies the decoder when pressed. The LED blinks three times when the decoder is

paired to a NAV encoder (see Pairing devices via front panel on page 5).

Operation

Power

When power is applied, the decoder runs a series of self-tests that blink the front panel Power LED and all other indicators. The decoder

then boots the NAV operating system. It can take approximately 45 seconds for self-test and system startup to complete. When the

process is complete, the Power LED lights steadily.

NOTE: The decoder is NOT operational until the boot process is complete (the Power LED is lit steadily).

System Operation

The decoder can be congured and controlled using embedded web pages or Extron Toolbelt (see the NAV SD 511 User Guide available

at www.extron.com and the Toolbelt Help ﬁle).

NOTE: The “Connection via web pages,” Connection settings, and Pairing devices via front panel procedures (see page 5) may

NOT be necessary if your system includes a NAVigator System Manager.

Connection via web pages

Connection to the decoder and its embedded web pages can be made via either the front panel Conguration (USB) port (using IP over

USB technology) (see gure 2, Aon page 2) or the rear panel NAV 1G port (see figure 1, Aon page 1).

Access the decoder using HTML pages as follows:

1. Start a web browser.

NOTES:

• Suggested browsers to fully support the NAV system are: Google Chrome™, Mozilla Firefox™, and Microsoft®Edge™.

• The network must be properly congured for multicasting (IGMP). Failure to do so may result in degraded performance.

2. Enter the IP address of the decoder in the browser Address field.

NOTES:

• Default settings:

Port DHCP IP address Subnet mask

Conﬁg (USB)*203.0.113.22

NAV 1G (Fiber)On

* For the Config port, the address for IP over USB

CANNOT be changed.

If the unit does not receive a DHCP address,

a self-assigned Link Local Address, is assigned in

the range 169.254.X.X.

• If you use IP over USB, Extron recommends waiting a minute after plugging in the cable for your PC to identify the USB

connection as a valid Ethernet port.

3. Press the keyboard <Enter> key. The browser

displays a privacy error message (see figure 3 at right

for an example in the Chrome browser).

4. Click Advanced (see figure 3, 1). The button changes

to Hide Advanced and explanatory text and a link

appear below the button.

5. Click Proceed to <IP address>(unsafe) (2). The

browser opens to the Login dialog box (see figure 4).

11111111111111

22222222222222

3333

33333333

Figure 4. Login Dialog Box

6. Enter the Username (see figure 4, 1) and Password (2) and click Sign In (3). The browser opens to the embedded web pages

(see figure 5 on page 5).

NOTES:

• The default Username is admin.

• The factory congured passwords for all accounts on this device have been set to the device serial number. If the password

is reset, the decoder reverts to the default password, which is extron.

• Usernames and passwords are case sensitive.

1111111111

1111

2222222222

2222

Figure 5. HTML Page

1111111111

1111

2222222222

2222

Figure 3. Privacy Error Message (in Chrome Browser)

NAV SD 511 • Setup Guide (Continued)

NOTE: Detailed descriptions of communication, conguration, and monitoring are provided in the NAV SD 511 User Guide,

available at www.extron.com.

Connection settings

View and change connection settings as follows:

1. On the home page, click Settings (see figure 5, 1) and then Network Connection (2). The Network Connection pane opens

(see figure 6), showing protected views of the network connection settings.

NOTE: Editing of connection settings is disabled when the

device is assigned to an Extron NAVigator System Manager.

2. To change the settings, click Edit (see figure 6, 1). The Edit button

changes to Save.

3. Click in the desired field (2) and edit it as necessary.

4. Repeat step 3 as necessary for other values.

5. Click Save.

Pairing devices via front panel

Pair devices as follows:

AV SD 511

1. Use a Tweeker or other small screwdriver to press

and hold the encoder front panel ID button for

approximately 3 seconds, until the ID LED blinks. The

encoder enters pairing mode, which allows decoders to

receive the AV and USB streams from encoders.

2. One at a time, use a Tweeker or other small screwdriver

to press and hold the decoder front panel ID button for approximately 3

seconds, until the ID LED blinks three times. The decoder is now paired

to the encoder.

3. Repeat step 2 for each decoder.

4. Use a Tweeker or other small screwdriver to press and release the

encoder front panel ID button. The encoder exits pairing mode.

5. Repeat steps 1 through 4 to pair decoders to other encoders.

After all devices are connected, powered on, and paired, the system is fully operational.

Operation in a System with a NAVigator

The Extron NAVigator is a system manager that easily congures and controls the NAV System. The NAVigator supports 16 endpoints by

default, but a LinkLicense can upgrade its capabilities to support up to 240 endpoints.

See the NAVigator User Guide, available at www.extron.com for details.

1111111111

1111

2222222222

2222

Figure 6. Network Connection Pane

68-3606-50 Rev. A

01 21

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Connection Details

LockIt®Lacing Brackets

1. Plug the HDMI or USB cable into the panel connection (see 1, at right for an HDMI example).

333

111

555

444

222

2. Loosen the connection mounting screw from the panel enough to allow the LockIt lacing bracket to

be placed over it (2). The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the connector (3), then tighten the screw

to secure the bracket.

ATTENTION:

• Do not overtighten the connector mounting screw. The shield it fastens to is very thin

and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur. Le blindage auquel elle est

attachée est très n et peut facilement être dénudé.

4. Loosely place the included tie wrap around the connector and the LockIt lacing bracket as shown (4).

5. While holding the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any excess length (5).

Analog audio output connector EXT connector

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

No Ground Here

Tip

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T568B

TP Wires

12345678

Pins:

Control connector Power connector

TxRx

RxTx Gnd

IR Device

Control Connectors

Remote and Sync Connectors

RS-232 Device

Tx Rx GSG

RS-232 IR

CONTROL

5VS

RxTx Gnd

Sync Device

RS-232 Device

Tx Rx GS5V

RS-232

Sync

CONTROL

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) MAX

SECTION A–A

Andere Handbücher für NAV SD 511

Inhaltsverzeichnis

Andere Extron electronics Medienkonverter Handbücher

Extron electronics

Extron electronics VS 200 SL Bedienungsanleitung

Extron electronics

Extron electronics mediaport 200 Bedienungsanleitung

Extron electronics

Extron electronics Balanced and Unbalanced Audio Converter BUC... Bedienungsanleitung

Extron electronics

Extron electronics VSC 700 Bedienungsanleitung

Extron electronics

Extron electronics DVS 605 Bedienungsanleitung

Extron electronics

Extron electronics CVC 100 Bedienungsanleitung

Extron electronics

Extron electronics NAV SD 501 Bedienungsanleitung

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Bedienungsanleitung

Extron electronics

Extron electronics VSC 900 Bedienungsanleitung

Extron electronics

Extron electronics IN1404XT Bedienungsanleitung

Extron electronics

Extron electronics Sync Converter/Stabilizer SCS 300 Bedienungsanleitung

Extron electronics

Extron electronics SMD 101 Bedienungsanleitung

Extron electronics

Extron electronics Multi Video Processor MVP 104GX Bedienungsanleitung

Extron electronics

Extron electronics ISS 506 Series Bedienungsanleitung

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Handbuch

Extron electronics

Extron electronics Two InpuT VIdeo Scaler IN1502 Bedienungsanleitung

Extron electronics

Extron electronics VSC 900 Bedienungsanleitung

Extron electronics

Extron electronics QSD 204 Bedienungsanleitung

Extron electronics

Extron electronics NAV 10SD 501 Bedienungsanleitung

Extron electronics

Extron electronics BUC 202 Bedienungsanleitung

Extron electronics

Extron electronics Digital Video Scaler Series Bedienungsanleitung

Extron electronics

Extron electronics DVI-RGB 100 Bedienungsanleitung

Extron electronics

Extron electronics DSC 3G-HD A Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung