Extron electronics VM 700T Bedienungsanleitung

VM 700T Mounting Kit Installation Guide

Overview

The Extron®VM 700T is

an adapter that provides a

VESA‑mounting option for the

TLP 700TV TouchLink™panel.

Four holes, one in each corner

allow the adapter to ﬁt any third‑party VESA Type D 75 mm mounting kit.

This guide provides basic instructions for an experienced installer to mount and

perform initial conﬁguration on the TLP 700TV.

Using the VM 700T mounting kit

The TLP 700TV comes assembled with a stand that allows it to be placed on a desk‑top. The stand can also be

removed and replaced with the Extron VM 700T VESA mount adapter kit (part # 70‑692‑01). This kit ﬁts into any

third‑party VESA Type D 75 mm wall mount system as follows:

1. Determine the best location for wall‑mounting the TLP 700TV.

2. Follow the manufacturer’s instructions to attach the VESA mounting kit to the wall.

WThe third-party VESA mounting kit must be attached to a wall stud to support the weight of the mounting

arm and the TLP 700TV unit.

3. Run the cables for power, LAN, and video (two BNC connectors) to the installation site.

4. Remove the TLP 700TV from its packaging or, if the TLP 700TV has previously been used as a free‑standing,

desk‑top unit, remove all cables to the back of the base.

5. At the bottom, the two plastic cover plates for the

stand are held together by a Phillips head screw

near the base. Remove the screw in the recessed slot

at the front of the stand, close to the base.

6. At the top, the two plastic plates covering the stand

are held together by four locking tabs on the back

cover plate ﬁtting into four slots on the front cover

plate. Squeeze the sides of the front plate at the top

so that the tabs are no longer seated in the slots.

68-1792-01

Rev. A 08 09

75mm

2.95”

75mm

2.95”

VM 700T Mounting Kit Installation Guide, Continued

7. Remove the back cover to reveal the metal stand and the

cables connecting the circuit board in the base to the touch

panel screen.

8. Cut the plastic tie holding the cables to the metal

stand.

9. Disconnect the power, LAN, audio, LED, and two

BNC cables from the circuit board in the base.

10. Remove the snake‑skin cover protecting the

cables.

11. Tilt the screen down to reveal the Phillips head screws securing the

screen to the hinged bracket at the top of the stand. Remove the

screws and save them for use with the VM 700T VESA mounting kit.

NSave the two screws for use with the VM 700T mounting kit.

12. Thread the cables through the gap between the top bracket and

the stand. Place the screen, face down, on a soft cloth.

TIf it is difﬁcult to ﬁt the BNC connectors through the space

between the top bracket and the stand, adjust the angle of the

bracket to make the space as large as possible.

Remove back cover.

Remove (2) Screws

Adjust bracket and thread cables through.

Remove Snake-skin Cover

Remove (cut) Plastic Tie

Remove all Cables

from Base

13. Remove and save the three Phillips head screws holding the plastic

molding to the back of the screen.

14. Disconnect the audio, LED, and power cables from the back panel of

the screen.

The audio cables are the black and white pair, wound around a•

ferrite core.

The power cables are the red and black pair, terminated with a•

blue, 2‑pole captive screw connector.

The LED cables are the black and white pair, without a ferrite core.•

NNone of the cables that are connected with a plastic tie should be

disconnected.

NSave the blue power cable connector for later use.

15. Replace the orange 2‑pole captive screw connector on the provided power supply with the blue connector from

the power cable disconnected in step 14.

CThe power supply provided with the TLP 700TV is intended for use with the power supply input in the

base. In order to use the power supply with the rear panel power input the captive screw connector must be

replaced.

16. Thread the cable from the power supply through the slot in the plastic

molding and connect it to the direct input captive screw input on the rear

panel.

17. Thread the remaining cables from the rear panel (2 BNC and 1 LAN) through

the slot in the plastic molding. Reattach the molding to the back of the screen,

using the three screws saved from step 13.

Remove (3) Screws

PowerLAN S video

Input

Replace Molding

SECTION A–A

Ridges

Smooth

Power Supply

Output Cord

A A

3/16”

(5 mm) Max.

LED Audio Power

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.15 68

+86.21.3760.15 66 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

VM 700T Mounting Kit Installation Guide, Continued

18. Hold the remaining cables towards the bottom of the

recess in the plastic moulding.

19. Holding the VM 700T mounting plate at a slight angle,

slide the center bar under the cables and into the recess, so

that it sits ﬁrmly at the bottom of the recess.

20. Secure the bracket to the screen, using the two screws saved from

step 11.

21. Attach the mounting plate to the bracket that was wall‑mounted in

step 2.

22. Plug in the rear panel cables, as required.

NWhen the base is removed from the TLP 700TV, video connections are via BNC connectors, and there is no audio

input.

Inhaltsverzeichnis

Andere Extron electronics Rack & Stand Handbücher

Extron electronics

Extron electronics FCMP 44 Bedienungsanleitung

Extron electronics

Extron electronics PoleVault Systems PVS 300 Bedienungsanleitung

Extron electronics

Extron electronics FOX3 Matrix Series Bedienungsanleitung

Extron electronics

Extron electronics UTS 100 Series Bedienungsanleitung

Extron electronics

Extron electronics MLM 84 Flex55 Bedienungsanleitung

Extron electronics

Extron electronics WMK 160 Bedienungsanleitung

Extron electronics

Extron electronics MMK 1 Bedienungsanleitung

Extron electronics

Extron electronics UTR 104 Bedienungsanleitung

Extron electronics

Extron electronics MediaLink MLM-UDSM Bedienungsanleitung

Extron electronics

Extron electronics MBU 149 Bedienungsanleitung

Extron electronics

Extron electronics PMK 155 Bedienungsanleitung

Extron electronics

Extron electronics SMK 1 Bedienungsanleitung

Extron electronics

Extron electronics RM 700M Bedienungsanleitung

Extron electronics

Extron electronics PMK 150 Bedienungsanleitung

Extron electronics

Extron electronics UPB 125 Bedienungsanleitung

Extron electronics

Extron electronics USFM 100 Bedienungsanleitung

Extron electronics

Extron electronics Wall Mount Assembly Kit V-LockTM Bedienungsanleitung

Extron electronics

Extron electronics SMK V SB 33 Plus Bedienungsanleitung

Extron electronics

Extron electronics SMK V SB 33 Bedienungsanleitung

Extron electronics

Extron electronics SMK 2 Bedienungsanleitung

Extron electronics

Extron electronics PMK 560 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung