Extron electronics TLI Pro 201 Bedienungsanleitung

Product Category

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLI Pro 201 and TLSI 201 • Setup Guide

Overview

The Extron TLI Pro 201 is a TouchLink®Interface scaler that integrates a third-party touchscreen display as a point of control

within an Extron Pro series control system. The scaled output supports resolutions up to 4K @ 30 Hz. The Extron TLI Pro 201

provides annotation features that allow users to draw, point, or type on video sources during presentations.

The TLSI 201 is a display interface that centralizes information about the TouchLink scheduler system.

This guide provides instructions for experienced installers to mount and install the TLIPro 201 or TLSI 201 and to create a basic

conguration. For more complete instructions, see the TLI Pro 201 and TLSI 201 User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

Toolbelt — Provides device discovery, device information, rmware updates, and conguration of network settings,

system utilities, and user management for TouchLink Pro devices.

TLI Pro 201

GUI Designer — For designing layouts for third party touchpanel interfaces.

Global Configurator®Professional and Global Configurator Plus — For setting up and conguring the control

processor and interface.

Global Scripter®— Provides an integrated development environment for Extron control systems programming.

TLSI 201

Room Agent™ — Room booking software for conguring the TLSI 201 for room scheduling.

NOTE: All ve software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status — (on or off). If DHCP is off, you must also obtain:

IP address Subnet mask Gateway

User name — This can be either admin or user.

Password — The factory congured passwords for all accounts on this device have been set to the device serial

number. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password will be the default password conguration. The default

password is extron (for either admin or user).

Make a note of the interface MAC address.

Mount and Cable All Devices

Mount the units. Place the interface on a convenient surface, mount it in a standard rack, or use an under-table mounting

kit (see the TLI Pro 201 and TLSI 201 User Guide, at www.extron.com). To mount the third-party touchpanel follow the

instructions provided by the manufacturer.

Connect cables to the interface (see Rear Panel Connectors and Features on the next page).

Connect the required HDMI source to the HDMI input (TLI Pro 201 only).

Connect the HDMI output from the interface to the third-party touchpanel.

Connect the USB port from the interface to the third-party touchpanel.

NOTE: The USB connection passes information to the interface about where on the screen the touchpanel was

pressed. To use a normal monitor, instead of a touchscreen, connect a mouse to the USB connection. Use the

mouse to click on screen icons.

www.extron.com

TLI Pro 201 and TLSI 201 • Setup Guide (Continued)

Connect the Ethernet cable. The interface must be powered by PoE+.

ATTENTION:

• Do not power on the TLI Pro 201 or TLSI 201 until you have read the Attention in the Rear Panel Features section of

the TLI Pro 201 User Guide.

• Ne branchez pas le TLI Pro 201 ou le TLSI 201 avant d’avoir lu la mise en garde dans la section «Rear Panel

Features» du TLI Pro 201 UserGuide.

Set up the Interface for Network Communication

Connect the PC that you will use for setup on the same Ethernet subnetwork as the interface. If you are using the

TLI Pro 201, you must also connect a control processor to the same subnetwork. The TLSI 201 does not require a control

processor.

Use the Setup Menu (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,

gateway, and related settings for the network interface.

Conﬁgure the User Interface

TLI Pro 201 — The Global Conﬁgurator Professional Help File, the Global Conﬁgurator Plus Help File, and the GUI Designer

Help File provide step-by-step instructions and more detailed information. The Global Congurator Professional and Global

Congurator Plus help les include an introduction to the software and sections on how to start a project and conguration.

TLSI 201 — Use Room Agent to congure the TLS touchpanels. For complete instructions about conguring the TLSI 201, see

the Room Agent Help File, User Guide, and Quick Start Guide at www.extron.com.

Rear Panel Connectors and Features

The TLI Pro 201 and TLSI 201 have identical rear panels. For complete information about the rear panel connectors and features,

see the TLI Pro 201 and TLSI 201 User Guide.

AAABBBC

CCD

USB LAN/PoE+

OUTPUTINPUT

Figure 1. TLI Pro 201 Rear Panel

ATTENTION:

• The TLI Pro 201 and TLSI 201 are Power over Ethernet (PoE 803.3at, class4) compliant. Do not connect the power

supply before reading the Attention in the Rear Panel Features section of the TLI Pro 201 and TLSI 201 User Guide.

• Le TLI Pro 201 et le TLSI 201 supportent l’alimentation via Ethernet (PoE 803.3at, classe4). Veuillez lire la partie

« Attention » dans la section « Rear Panel Features » du TLI Pro 201 and TLSI 201 User Guide, avant de mettre sous

tension les écrans tactiles.

gure 1

AHDMI input (TLI Pro 201 only) — Plug the cable from the input source device

into this female HDMI type A port. Use the provided LockIt HDMI lacing bracket

to secure the HDMI connector:

1. Plug the HDMI cable into the panel connection.

2. Loosen the HDMI connection mounting screw from the panel enough to

allow the LockIt lacing bracket to be placed over it. The screw does not

have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI

connector, then tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connection mounting screw. The

shield it fastens to is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le

blindage auquel elle est attachée est très n et peut facilement

être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the

LockIt lacing bracket as shown.

5. While holding the connector securely against the lacing bracket, tighten the

tie wrap, then remove any excess length.

HDMI input

Figure 2. Securing the HDMI Connector

Product Category

BHDMI output (see ﬁgure 1 on the previous page) — Connect this female HDMI type A port to a third-party touch screen. A

full list of compatible resolutions is provided in the TLI Pro 201 and TLSI 201 User Guide.

Use the provided LockIt brackets to secure the connector to the TLI Pro 201 or TLSI 201 unit (see HDMI input, on the

previous page).

CUSB port — supports High-speed USB 2.0 control. Plug a Type-A USB cable from the third-party touchpanel into this port.

NOTE: To use a monitor that is not a touchpanel, connect a mouse to this port.

DLAN and PoE+ port — Use an Ethernet cable to connect this port to the network via a PoE+ power sourcing equipment

(PSE, not provided). This can be a power injector (see gure 3) or PoE+ switch.

NOTE: These interfaces are shipped without a PoE+ PSE. This must be purchased separately.

Front Panel Features

SIGNAL

INPUTOUTPUT

HDCP

TLI Pro 201

R MENU

Figure 4. TLI Pro 201 Front Panel

APower LED — Indicates the power status and the reset status of the unit.

BReset button (recessed) — allows the unit to be reset in any of three different modes. It also allows the user to toggle

between enabling and disabling the DHCP client. A brief summary of the reset modes is given below. For more information

see the TLI Pro 201 and TLSI 201 User Guide.

CMenu button (recessed) — opens the Setup Menu (see the next page) and Calibration screen for the interface:

• Press the button briey (less than 2 seconds) to open the internal menu screens.

• Press and hold the button (at least 2 seconds) to open the Calibration screen. Follow the on-screen instructions to

calibrate the touchpanel.

• Press the button briey (less than 2 seconds) for a second time to close the current screen without saving any changes.

DStatus LEDs —

• The Signal LEDs light green when a video signal is detected and are unlit when no signal is detected.

• The HDCP LEDs light green when HDCP content is detected and are unlit when HDCP content is not detected.

100-240V 50/60 Hz

1.1A MAX INPUT

LAN POWERED TLP

OUTPUT

To network switch To interface

Figure 3. PI 140 Power Injector

gure 3 Extron recommends the Extron PI 140 power injector (see gure 3). Your power

injector may look different.

1. Use an Ethernet cable to connect the LAN/PoE+ port of the interface to the

power output of the 803.3at, class4 compliant PoE+ power injector.

2. Connect the network input of the power injector to a network switch or router.

Alternatively, use an Ethernet cable to connect the LAN/PoE+ port of the interface to

a PoE+ switch.

468-3514-50 Rev. A

02 20

TLI Pro 201 and TLSI 201 • Setup Guide (Continued)

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Reset Modes: a Brief Summary

The TLI Pro 201 and TLSI 201 offer the following reset modes:

• Use factory firmware: Press and hold the Reset button (Figure 4, B) while applying power to the unit. Use this

mode to replace rmware in the event of rmware failure.

• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Power LED (Figure4,A) ashes

twice, release and momentarily press the Reset button. Use this mode to reset all network

settings without affecting user-loaded les.

• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Power LED ashes three times,

release and momentarily press the Reset button. Use this mode to return the device to

factory default settings.

NOTES:

• The factory congured passwords for all accounts on this device have been set to

the device serial number. Passwords are case sensitive.

• If the device is reset to default settings, the password is the default password

conguration. The default password is extron.

• Enable or Disable the DHCP

Client:

This mode toggles between DHCP enabled and DHCP disabled. Press the Reset button

ve times, consecutively. After the fth press, do not press the button again within 3

seconds. If DHCP was enabled, it is now disabled and the Power LED blinks three times. If

DHCP was disabled, it is now enabled and the Power LED blinks six times.

Setup Menu

Press the Menu button (see Front Panel Features, Con page 3)

to open the setup menu (see gure 5). There are six available screens

that are selected by pressing the appropriate button in the navigation

bar at the top of the screen.

• The Status screen is read-only and provides a summary of the

other screens.

• The Network screen is used to edit the network settings (DHCP

setting, IP, subnet mask and gateway addresses).

• The Output screen is used to congure the image shown by the

third-party display, using built-in test patterns and EDID.

• The Audio screen is used to set audio levels.

• The Input screen is used to congure the input video signal.

• The Advanced screen provides information about the system and

the GUI project

Info

Model: TLI Pro 201

Part Number: 60-1669-01

Firmware

Version: 1.00

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLI-AB-CD-EF

Output

TLI Output:

GUI Project:

Sleep Timer:

1080p @ 60Hz

5 Minutes

Audio

Master Volume:

Master Mute:Off

Input

HDMI:No Signal

Status Output AudioAdvanced Exit

NetworkInput

Advanced

Controller IP:192.168.254.250

Project Size:N/A

Bootloader

Version: 1.00

PoE Status:Active

Figure 5. Setup Menu

Press the Exit button to close the setup menu.

For more information about the setup menu, see the TLI Pro 201 and TLSI 201 User Guide at www.extron.com.

Andere Handbücher für TLI Pro 201

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Aufnahmegeräte Handbücher

Extron electronics

Extron electronics Ethernet Control Interface IPL T PCS4 Bedienungsanleitung

Extron electronics

Extron electronics SSP 7.1 Bedienungsanleitung

Extron electronics

Extron electronics IPL T S Series Bedienungsanleitung

Extron electronics

Extron electronics DSC HD-HD 4K Plus A Series Bedienungsanleitung

Extron electronics

Extron electronics RAC 104 Bedienungsanleitung

Extron electronics

Extron electronics IPL EXP PDU4H Bedienungsanleitung

Extron electronics

Extron electronics SSP 7.1 Bedienungsanleitung

Extron electronics

Extron electronics RGB 326 Bedienungsanleitung

Extron electronics

Extron electronics RGB 109xi Bedienungsanleitung

Extron electronics

Extron electronics RGB 203 Rxi Bedienungsanleitung

Extron electronics

Extron electronics RGB 158xi Bedienungsanleitung

Extron electronics

Extron electronics RGB 500 AKM Bedienungsanleitung

Extron electronics

Extron electronics RGB 190F Bedienungsanleitung

Extron electronics

Extron electronics RGB 202 VS SL2 Bedienungsanleitung

Extron electronics

Extron electronics KNX 100G Bedienungsanleitung

Extron electronics

Extron electronics RGB 302 Bedienungsanleitung

Extron electronics

Extron electronics CIA111 Bedienungsanleitung

Extron electronics

Extron electronics USB-C HD 101 Bedienungsanleitung

Extron electronics

Extron electronics TLI Pro 201 Bedienungsanleitung

Extron electronics

Extron electronics RGB 472xi Bedienungsanleitung

Extron electronics

Extron electronics IPL T SF Series Bedienungsanleitung

Extron electronics

Extron electronics SSP 7.1 Bedienungsanleitung

Extron electronics

Extron electronics RGB 103 Bedienungsanleitung

Extron electronics

Extron electronics DVI-RGB 150 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch