Extron electronics DTP T USW 333 Bedienungsanleitung

DTP T USW 333 • Setup Guide

This guide provides instructions for an experienced installer to set up and operate the

Extron DTP T USW 333 switching video transmitter. The DTP T USW 333 transmitter switches among

an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver, can

extend the selected signal up to 330 feet (100 m). If the selected input is HDMI, the extended video

signal is HDCP-compliant.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter as required.

Step 2 — Making Connections

Inputs

aInput 1 (RGB) connector — Connect a VGA cable between this port and the VGA output port of the analog video source.

bInput 2 and 3 (HDMI) connectors — Connect HDMI cables between these ports and the HDMI output ports of the digital video

sources.

NOTE: See the LockIt®Lacing Brackets on page 3 of this guide to securely fasten the HDMI connectors to the transmitter.

cAudio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.

NOTE: Audio is not embedded in the HDMI signal; it is transmitted simultaneously and is present on all inputs.

Over DTP RS-232 and IR pass-through

dRS-232 and IR connector — To pass serial or infrared data or control signals on the Over

DTP RJ-45 output, connect the controlling device to the transmitter via the RS-232 and IR

captive screw connector. Connect the device to be controlled to the receiver.

DTP output to receiver

ATTENTION: Do not connect this device to a computer data or telecommunications network.

eDTP RJ-45 connector — Connect the transmitter DTP Out port to the DTP In port on the receiver. Extron

recommends that you terminate both cable ends in accordance with the following specications, at a

minimum:

• TIA/EIA T 568B •CAT 6a, shielded

• 24 AWG, solid conductor

Signal LED — Lights when the unit is outputting a TMDS clock signal on the DTP output.

Link LED — Lights when a valid link is established between the units on the DTP cable.

Remote control

fRemote Contact port — If desired, for contact closure control, plug a locally-constructed contact closure control device into this

3.5 mm, 4-pole captive screw port. Momentarily short the pin for the desired input (1, 2, or 3) to G to select that input. To force an

input to be always selected, leave the short in place.

NOTES:

• Contact closure control overrides front panel input selections.

• For contact closure control, auto-input switching mode must be off (see Selecting the switch mode on the next page).

POWER

12V

--A MAX

Rx GTx RxTxG

RS-232 IR

RxTx

RGB, Y, R-Y, B-Y HDMI HDMI

SIG LINK

DTP OUT

AUDIO

CONTACT RS-232TALLY

123G 123+V

RESET

INPUTS

OVER DTPREMOTE

4 6

10 51 2 923 87

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIAT

568B

TP Wires

12345678

Pins:

TxRx

RxTx

Gnd

IR Device

RS-232 Device

RxTx RxTxG

RS-232 IR

OVER DTP

DTP T USW 333 • Setup Guide (Continued)

gRemote Tally port — If desired, to remotely identify the currently selected input, plug a locally-constructed device into this 3.5 mm,

4-pole captive screw connector. Connect the power wire for the device into the +V pin and connect the ground wire for the each

indicator into the corresponding tally output pin: 1, 2, or 3.

When an input is selected, by either contact closure or front panel selection, the corresponding tally output pin shorts to ground,

closing the circuit and lighting the connected indicator (LED).

hRemote RS-232 port — Plug a serial RS-232 device into the switching transmitter via this rear

panel 3.5 mm, 3-pole captive screw connector for remote control of the switching transmitter.

Reset button

iReset button — This button initiates two levels of reset. For different reset levels, use an

Extron Tweeker or small screwdriver to press and hold the recessed button either while the

switcher is running or while applying power. See the DTP T USW 333 User Guide, available at www.extron.com, for details.

Power

jPower connector — Connect an IEC power cord between the included 12 VDC

power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to

either unit, transmitter or receiver, as shown at right. Use the included tie-wrap to

strap the cord to the captive screw connector.

NOTE: Only one power supply is required. A single power supply connected to

either unit in the pair powers both units. A power supply is included with the

transmitter.

Front panel Conﬁguration port

aConfiguration port — Plug a PC or other controlling device into the switching transmitter via this front

panel mini-USB connector for remote conguration of the switching transmitter.

Operation

Switching inputs

Select the desired input by pressing the associated input button. Observe that the

LED for the selected input lights.

NOTE: The switcher must be in normal (manual) mode (see below).

Selecting the switch mode

In auto-input switching mode, the switcher selects to the highest numbered input

with a sync signal present. Turn auto-input switching mode on and off as follows:

1. Press and hold the Mode (Input 1) button.

2. Press and release the button for the desired mode:

Auto (Input 3) — The Auto Switch LED lights.

Normal (Input 2) — The Auto Switch LED goes off.

3. Release the Mode button.

Locking and unlocking the front panel

(Executive mode)

The switcher has a front panel lock feature that locks the front panel. If you try to make

front panel input selections when the panel is locked, all front panel LEDs ash three

times. Toggle the front panel lock on and off by pushing and holding all three Input

buttons simultaneously for 5 seconds. All front panel LEDs ash three times.

Release the buttons.

Interpreting the Status LEDs

Signal LEDs (1 through 3) —Indicate that the switcher detects horizontal sync

(Signal LED 1) or TMDS clock (Signal LED 2 and Signal LED 3) signals on the associated input.

HDCP LEDs (2 and 3) —Indicate that the corresponding input signal is HDCP encrypted.

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) Max.

SECTION A–A

REMOTE

RxTx Gnd

RS-232 Device

GRxTx

RS-232

AUTO

SWITCH

CONFIG

MODE NORMAL

AUTO

Press the button.

The LED lights

green.

123

MODE NORMAL AUTO

AUTO

SWITCH

Press and HOLD the Mode button.

Press and release the Auto or Normal button.

Release the Mode button.

Auto Switch lights (auto)

or goes out (normal).

MODE NORMAL AUTO

Press the and

HOLD

the all three Input buttons.

All three LEDs flash three times. Release the Input buttons.

HDCP

SIGNAL

STATUS

123

LockIt®Lacing Brackets

Use the included LockIt Lacing Brackets to securely fasten both HDMI cables as follows.

1. Plug the HDMI cable into the panel connection.

2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing

bracket to be placed over it. The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the

screw to secure the bracket.

ATTENTION:Do not overtighten the HDMI connector mounting screw. The shield it fastens

to is very thin and can easily be stripped.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as

shown.

5. While holding the connector securely against the lacing bracket, use pliers or similar tools to

tighten the tie wrap, then remove any excess length.

Application Diagram

POWER

12V

--A MAX

Rx GTx RxTxG

RS-232 IR

RGB, Y, R-Y, B-Y HDMI HDMI

SIG LINK

DTP OUT

AUDIO

CONTACT RS-232TALLY

1 2 3 G 1 2 3 +V

RESET

INPUTS

OVER DTP REMOTE

Tx Rx G Tx Rx

RS-232 IR

OVER DTP

OUTPUTS

AUDIO

131

100

LINK

ACT

COMIR INPUT RELAY

TX RX

IPL250

OFF

DISPLAY

MUTE

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

Ext

ron

DTP T

USW 333

P Transmitter

ptop

Laptop

Document

Camera

TCP/IP

AV Device

Control

Switcher

Control

VGA

HDMI

Extron

TouchLink

Control

System

Extron

IPL 250

CATx Cable

Up to 330' (100 m)

Extron

DTP HDMI 330 D Rx

Receiver

HDMI with

Embedded

Audio

Flat Panel Displa

with Speakers

AV Device

Control

Figure 1. Typical Switching Transmitter Application

68-2564-50 Rev. A

01 14

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Andere Handbücher für DTP T USW 333

Inhaltsverzeichnis

Andere Extron electronics Sender Handbücher

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics XTP T HWP 101 Bedienungsanleitung

Extron electronics

Extron electronics FOX T UWP 302 Bedienungsanleitung

Extron electronics

Extron electronics DTP T EU 4K 331 Bedienungsanleitung

Extron electronics

Extron electronics FOX3 T 301 Bedienungsanleitung

Extron electronics

Extron electronics DTP T HWP D Series Bedienungsanleitung

Extron electronics

Extron electronics DVI 201 Tx/Rx Bedienungsanleitung

Extron electronics

Extron electronics DTP T FB 232 Bedienungsanleitung

Extron electronics

Extron electronics HFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 330 Bedienungsanleitung

Extron electronics

Extron electronics XTP FT HD 4K Bedienungsanleitung

Extron electronics

Extron electronics PVT CV D Bedienungsanleitung

Extron electronics

Extron electronics TP T 15HD 45 Bedienungsanleitung

Extron electronics

Extron electronics MTP 15HD A Series Bedienungsanleitung

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics TP T 15HD AV Bedienungsanleitung

Extron electronics

Extron electronics FOX 500 Tx Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 202 Bedienungsanleitung

Extron electronics

Extron electronics TP Series Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 203 Bedienungsanleitung

Extron electronics

Extron electronics XTP T HWP 101 4K Bedienungsanleitung

Extron electronics

Extron electronics XTP T FB 202 4K Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX T HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics DTP T USW 233 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung