Extron electronics FOX T UWP 302 Bedienungsanleitung

Product Category

FOX T UWP 302 • Installation Guide

CLASS 1 LASER PRODUCT, see FOX T UWP 302 User Guide at www.extron.com.

This guide provides instructions for an experienced installer to install and connect the 3-gang Extron FOX T UWP 302 Universal

Wallplate Transmitter and switcher. It can t into a wall or oor box.

NOTE: The FOX T UWP 302 is not compatible with the FOX 3G HD-SDI,

FOX 3G DVC, or FOX AV models.

WARNING: Risk of serious physical injury. The transmitter outputs continuous

invisible light, which may be harmful to the eyes; use with caution.

• Do not look into the ber optic cable connectors or into the ber optic cables

themselves.

• Plug the attached dust caps into the optical transceivers when the ber optic

cable is unplugged.

Planning

CAUTION: Risk of personal injury. Failure to check these items may result in personal injury.

ATTENTION: Failure to check the items listed below may result in property damage.

Check that the installation meets the building, electrical, and safety codes.

Installation

Step 1 —Preparing the Mounting Surface

a. Install a UL-listed electrical junction box according to the instructions of the manufacturer.

b. Secure cables with clamps or ties to provide strain relief (see Making Rear Panel Connections below for necessary cables).

c. Trim back and insulate shields with heat shrink.

ATTENTION: To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable

clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

Step 2 —Making Rear Panel Connections

AFiber optic connector — Connect a ber cable between the Tx port on the FOX T UWP 302

and the Rx port on a receiver.

To return serial data from the receiver to the FOX T UWP 302, connect a ber cable between

the Rx port on the transmitter and the Tx port on the receiver.

BRemote RS-232 and Alarm connector — For serial RS-232 control of the FOX T UWP 302,

connect the host device to the leftmost poles (Tx, Rx, and G) of this 5-pole captive screw

connector. For remote monitoring of the status of ber optic link 2, connect a custom

monitoring device to the rightmost poles (1 and 2) of this 5-pole captive screw connector.

CPower connector —Connect the provided 12 VDC external power supply to this 3.5 mm,

2-pole captive screw connector.

Step 3 —Mounting

DAttach the FOX T UWP 302 to the junction box with screws.

TIP: If necessary, configure the device before attaching the

decorator-style faceplate in the step below (see Remote Control on

the next page or the FOX T UWP 302 User Guide for more details).

EAttach the decorator-style faceplate to the FOX T UWP 302 with the provided

screws.

POWER

HDMI

HDCP

AUDIO INPUT

HDMI INPUT

COMPUTER INPUT

AUDIO

Flush with

Wall Surface

Scr

ews or Nails

Wall Stud

Wall Box

Mounting

Screws

(6 Plcs)

EEEEEEEEEE

DDDDDDDD

Rear Panel Connectors from the Side View

AAAAAAAAAA

BBBBBBBB

CCCCCCCC

FOX T UWP 302 • Installation Guide (Continued)

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91-80-3055.3777

+91 80 3055 3737 FAX

Rev. B

04 17

Step 4 —Making Front Panel Connections

FConnect a source device to the HDMI connector.

TIP: Use an Extron LockIt®Lacing Bracket to secure

HDMI cables to the HDMI connector.

GConnect a video source to the Computer Input connector.

HConnect an audio source to the 3.5 mm TRS jack.

Operation

Remote Control

Connect a host device, such as a computer, to the mini-USB type B

cong port for serial control of the FOX T UWP 302. Use SIS commands or install the FOX Extenders Control Program

from the Extron Software Products DVD or check the Extron website, www.extron.com, for the latest version (see the

FOX T UWP 302 User Guide for remote control details).

Reset button

Press and hold the Reset button on the front panel to enter reset mode 1 or 5. If necessary, unscrew the screws

connecting the faceplate to the enclosure and remove the faceplate to access the Reset button.

Reset Mode Summary

Mode Activation Result Purpose/Notes

Factory Reset

(Mode 1)

Hold the Reset button down while

applying power to the device.

NOTE: After a mode 1 reset,

update the device with the

latest firmware version. DO NOT

operate the firmware version

that results from this mode

reset.

zThe device reverts to the factory default rmware.

zAll user les and settings (audio adjustments,

audio input selection, input selection,

auto-switch mode, picture adjustments, and

input video format) are maintained.

Use mode 1 to roll back

to factory rmware for

a single power cycle if

an incompatibility issue

arises.

Reset to Factory

Defaults (Mode 5)

Hold the Reset button down for about

9 seconds or until the Power LED

blinks three times. Then press the

Reset button momentarily

(for <1 second) within 1 second.

zMode 5 performs a complete reset to factory

defaults except for rmware.

zResets all user modiable congurations to

default values including real-time adjustments.

zThe power LED blinks 4 times in quick

succession during the reset.

Use mode 5 to start over

with conguration or

uploading.

NOTE: This is

equivalent to SIS

command ZXXX.

Indicators

Link 1 and Link 2 LEDs —Light to indicate ber light presence.

Power LED —Lights when the device receives 12 V from an external power supply.

PC LED —Lights when PC input is detected.

HDMI LED —Lights when HDMI input is detected.

HDCP LED —Lights if the HDMI input signal is HDCP-encrypted.

Audio LED —Lights when the device detects audio with the selected input. If the selected input has an analog audio

signal above -44 dBV, the Audio LED lights immediately, but turns off only after the audio signal level drops below the

threshold continuously for 10 seconds. If the selected input has digital embedded audio, the Audio LED lights and

remains lit as long as the digital audio signal is detected.

POWER

HDMI

HDCP

AUDIO

CONFIG

RESET

LINK 1

LINK 2

LINK 1

LINK 2

HDMI INPUT

AUDIO INPUT

COMPUTER INPUT

POWER

RESET

CONFIG

HDMI

HDCP

AUDIO

FFFFFFFFFF

GGGGGGGG

HHHHHHHH

Andere Handbücher für FOX T UWP 302

Inhaltsverzeichnis

Andere Extron electronics Sender Handbücher

Extron electronics

Extron electronics DTP2 T 202 FB Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Bedienungsanleitung

Extron electronics

Extron electronics TP Series Bedienungsanleitung

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics DVI 201xi TX Bedienungsanleitung

Extron electronics

Extron electronics TP T 15HD AV Bedienungsanleitung

Extron electronics

Extron electronics XTP T VGA Bedienungsanleitung

Extron electronics

Extron electronics DTP T FB 232 Bedienungsanleitung

Extron electronics

Extron electronics VERSATOOLS MTP Bedienungsanleitung

Extron electronics

Extron electronics CAT 5 Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX T HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics DTP T USW 233 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage MTP AV Series Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T/R 211 Bedienungsanleitung

Extron electronics

Extron electronics DTP T FB 332 Bedienungsanleitung

Extron electronics

Extron electronics DTP T HWP D Series Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 203 Bedienungsanleitung

Extron electronics

Extron electronics XTP T HDMI Bedienungsanleitung

Extron electronics

Extron electronics HFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics DTP T HD2 4K 230 Bedienungsanleitung

Extron electronics

Extron electronics XTP T HWP 101 Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics DTP T EU 232 Bedienungsanleitung

Extron electronics

Extron electronics TP T 15HD 45 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung