Fairford Agility AGY-010 Bedienungsanleitung

MAN-AGY-005. Version 01 (01/11/2017)

Innovation in soft start technology

agility

REMOTE KEYPAD USER GUIDE

MAN-AGY-005. Version 01

MAN-AGY-005. Version 01 (01/11/2017)

Remote Keypad User Guide

Fairford Electronics Ltd

Bristow House

Gillard Way, Ivybridge

PL21 9GG

www.fairford.com

[Full User Manual (MAN-AGY-001) available from www.fairford.com]

other soft copy of these deliverables. This document may not be reproduced, in full or in part,

without written permission. Enquiries about copyright of Fairford Electronics deliverables should

be made to Fairford Electronics Ltd. If, by permission of the copyright owner, any part of this

document is quoted, then a statement specifying the original document shall be added to the

quotation. Any such quotation shall be according to the original (text, figure or table) and may

not be shortened or modified.

MAN-AGY-005. Version 01 (01/11/2017)

Network Connection

For a configuration where there is only one agility

unit (one-to-one), the remote and

main unit can be directly cabled. See Diagram below:

ConnectionandOperation

The remote keypad (AGY-010) can be used to control,

monitor and program up to 32 agility

soft starters.

The unit is powered from the host agility

and

requires an Ethernet cable for communication

(Modbus RTU).

As the remote keypad acts as the Modbus master,

no additional master units must be placed within the

network. Failure to observe this may lead to erratic

behaviour, network failure and/or equipment

damage.

Keypad power must be enabled

on the agilityTM starter (see below)

Enabling Keypad Power: Scroll to DEVICE menu → KEYPAD menu → KEYPAD PWR = ON

MAN-AGY-005. Version 01 (01/11/2017)

For multiple base units connected to the keypad, the use of SGY-011, CBL-036 and

CBL-035 (terminator) is highly recommended. See diagram below.

Operation

Once connected to the agility

host unit/s, menu structures and programming are the

same as detailed in the agility

manuals MAN-AGY-001 and MAN-AGY-002 (both may

be downloaded from www.fairford.co.uk).

However, specific steps must be taken to connect the Remote Keypad to one or more

agility

host units.

Initial Power-Up

If the host agility

unit/s and the remote keypad have the default Modbus transmission

parameters set, and the host unit is powered and has Keypad power set to ‘on’, the

keypad will automatically communicate with the host. The following status screen will

be seen:

ConnectionandOperation(continued)

SGY-011

Close Jumper S6

(supplies power to AGY-010)

CBL-036

CBL-035

(last unit only)

Enable keypad

power

on this unit

only

Status of connected host

Control method

(Local, Remote, Modbus)

Modbus address

of connected unit

Navigation Wizard

(displays ‘active’ keys)

Motor Overload level

The agilityTM units must have: a unique Modbus address on each unit and identical

Parity/Baud rate values on each unit

Address = 1

Address = 2

Address = 3

MAN-AGY-005. Version 01 (01/11/2017)

If any of the Modbus communication parameters are dissimilar on the host unit or

remote keypad, communication will not be established. The keypad will display the

following screen:

By pressing the Right key, the user will be taken directly to the Modbus address

selection menu:

If the selected Modbus address is valid, the status screen is displayed:

Selecting Units To Monitor/Configure

When the Remote Keypad is attached to multiple agility

units on the Modbus network,

the user can switch between each unit by using the following method.

(continued over)

ConnectionandOperation(continued)

Only Right key is active

May show: Local, Remote or Modbus

Press CENTRE key

Use UP / DOWN

keys to select

address.

Press centre to

confirm

To simplify this selection process it is recommended that the host agilityTM units are

configured with consecutive Modbus addresses

MAN-AGY-005. Version 01 (01/11/2017)

Procedure:

1. Press the ‘Right’ key

2. Address selection screen will be shown

3. Press the ‘Centre’ key. Display will change mode

4. Use ‘Up’ or ‘Down’ keys to change address to the desired number (agility

address).

Press the ‘Centre’ key to confirm

5. Remote display will return to the Status screen and display the new address.

ConnectionandOperation(continued)

Modbus address

of connected unit

MAN-AGY-005. Version 01 (01/11/2017)

Mounting

Fix the unit to a flat, vertical surface using the mounting holes in the keypad enclosure.

•The orientation of the unit has the ‘TOP’ uppermost.

•The location allows adequate front access.

•The screen can be viewed

Do not install other equipment that generates significant heat close to the keypad.

Firmware Update

1. Download the latest firmware version from www.fairford.co.uk and copy the files to a

USB flash drive.

2. Power down the Remote Keypad and insert the USB flash.

3. Power-up the remote Keypad, the update will start automatically

4. When the update is complete (status screen shown), recycle the Remote Keypad

power.

Installation

Note: The host units and Keypad must have the same firmware version.

MAN-AGY-005. Version 01 (01/11/2017)

Inhaltsverzeichnis

Andere Fairford Tastenfeld Handbücher

Fairford

Fairford Synergy SGY-010 Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung