F&F BIS-409 Bedienungsanleitung
- 1 -
BIS-409
Bistable relay,
sequential, 4-function
Electronic bistable pulse relay BIS-409 allows switching on or off
the lighting or other device from several different points by pa-
rallel connected, momentary (bell) control switches.
Relay has 2 switching sections and allows for switching of 2 light-
ning circuits (branches) or other receivers from several different
points and in accordance with the preselected sequence
The relay power supply is indicated by a green LED U. Sequential
relay has 2 separate outputs: R1 and R2. Contact status (closed/
opened) is forced sequentially in accordance with a predeter-
mined program. Contacts switching to another state after sub-
sequent pulse from control button. R1 and R2 contact activation
is indicated by the relevant R1 and R2 red LED. After a power
failure, state of the contact is reset. When the power is back on,
the relay starts from the sequence number 0.
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.
- 2 -
»Subsequent pressings of a button repeat the sequence 0-1-2-3.
»Pressing the button again in less than 5 seconds repeats sequ-
ences 1-2-3.
»Pressing the button again after more than 5 seconds opens
both contacts (sequence 0).
»A long press of the button – in any sequence – opens both
contacts (sequence 0).
»After switching off both relays, pressing the button again re-
stores the state from before switching off (state memory). This
does not apply to relay power failure.
Work functions
- 3 -
»Subsequent pressings of a button repeat the sequence 0-1-2.
»Pressing the button again in less than 5 seconds repeats sequ-
ences 1-2.
»Pressing the button again aft er more than 5 seconds opens
both contacts (sequence 0).
»A long press of the button – in any sequence – opens both
contacts (sequence 0).
»After switching off both relays, pressing the button again re-
stores the state from before switching off (state memory). This
does not apply to relay power failure.
- 4 -
1.Disconnect the power supply.
2.Mount relay in the flush-mounted box.
3.Connect the power supply cables to PWR group: phase L-wire
to terminal 4 and neutral N-wire to terminal 2 or 3.
4.Momentary switches connected in parallel connect to terminal
1 and phase L-wire.
5.Powered receiver of R1 section connect in series to terminal
6, and powered receiver of R2 section connect in series to
terminal 5.
6.Set the required program (sequence) with the potentiometer.
1 control input
3 N power supply
4 L power supply
5 output – R1 section
6 output – R2 section
Mounting
Wiring diagram
- 5 -
BIS-409 is compatible with backlit buttons.
The maximum total backlight current of all connected
buttons must not exceed 5 mA.
power supply 165÷265 V AC
contact 1×NO
maximum load current (AC-1) 2×8 A
control pulse current 1 mA
total backlight current control buttons 5 mA
activation delay 0.1÷0.2 s
switch-off time (adjustable) 1÷15 min.
power indication green LED
power consumption
standby 0.15 W
on 0.6 W
tightening torque 0.4 Nm
working temperature -25÷50°C
ingress protection IP20
Technical data
- 6 -
tungsten halogen fluorescent energy-saving LED
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
Power table
Warranty
CE declaration
E211202
Inhaltsverzeichnis
Andere F&F Relais Handbücher
F&F
F&F PK-1Z-LED 230 V Bedienungsanleitung
F&F
F&F PP-2Z Bedienungsanleitung
F&F
F&F BIS-410-24V Bedienungsanleitung
F&F
F&F BIS-411BM-LED Bedienungsanleitung
F&F
F&F BIS-408i Bedienungsanleitung
F&F
F&F 5908312595533 Bedienungsanleitung
F&F
F&F PZ-829 RC Bedienungsanleitung
F&F
F&F BIS-411 1R1Z Bedienungsanleitung
F&F
F&F BIS-411 Bedienungsanleitung
F&F
F&F PP-1P Bedienungsanleitung
F&F
F&F PCS-506 Bedienungsanleitung
F&F
F&F BIS-411-LED Bedienungsanleitung
F&F
F&F FW-R2P Bedienungsanleitung
F&F
F&F FW-R2D Bedienungsanleitung
F&F
F&F PCS-516UNI Bedienungsanleitung
F&F
F&F SWITCH & ENERGY Wi-R1S1-P Bedienungsanleitung
F&F
F&F BIS-419-LED Bedienungsanleitung
F&F
F&F PK-2P Bedienungsanleitung
F&F
F&F BIS-410 Bedienungsanleitung
F&F
F&F PK-1P Bedienungsanleitung
