Fanimation Alamosa FP3820RP Bedienungsanleitung

OWNER’S MANUAL

READ AND SAVE THESE INSTRUCTIONS

Model No. FP3820RP

The Alamosa®

Ceiling Fan

Net Weight 18.9 kg (42 lbs)

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during

the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned

to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or

reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to

defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser

will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or

reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we

will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,

tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of

heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan

or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac-

company authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid

damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or

implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and

fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation

will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,

except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary

from state to state.

10. A certain amount of wobble is normal and should not be considered a problem or a defect.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

Table of Contents

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

How to Wire Your Ceiling Fan - Pull Chain. . . . . . . . . . . . . . . . . . . . . . . . 8

Installing the Canopy Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Assembling and Mounting the Fan Blades, & Adapter/Switch Hsg . . 10

Operating Instructions - Pull Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Blade Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Exploded-View Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such

as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before

servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan

must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed

electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. See page 4 of owner’s manual for

support requirements. Consult a qualified electrician if in doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical

knowledge or experience, have your fan installed by licensed electrician.

WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for

use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property

damage.

WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,

balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

This Manual is Designed to Make it as Easy as Possible for You

to Assemble, Install, Operate, and Maintain Your Ceiling Fan

Unpacking Instructions

For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all

steps have been completed and will be helpful in ﬁnding your place should you be interrupted.

Wiring outlet box and box connectors must be of type

required by local code. The minimum wire would be a 3-

conductor (2-wire with ground) of the following size:

NOTE: Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are missing,

contact your local retailer.

Tools Needed for Assembly Materials

Wire Size A.W.G.Installed Wire Length

Up to 50 ft.

50 - 100 ft.

NOTE: If you are uncertain of part description, refer to

exploded view illustration. (Figure 1, page 15)

1. Check to see that you have received the following

parts:

• Fan Motor/Hub assembly

• Housing Switch Cup/

Adapter assembly

• Downrod/Hanger Ball

assembly

• Blade Holder (5)

• Wood Blades (5)

• Ceiling Canopy

• Hanger Bracket

Blade Holders

Hardware Bags

Fan Motor/

Hub Assembly

Downrod/

Hanger Ball

Assembly Hanger

Bracket

• One Phillips head screwdriver

• One stepladder

• One ¼˝blade screwdriver

• One wire stripper

•Three wire connectors

(supplied)

Ceiling

Canopy

Wood Blades

• Hardware bags:

– Eleven ¼-20 x 14mm (blade

holder to fan motor hub) screws

– Sixteen 3/16-24 x 15mm (blade

to blade holder) pan-head

screws, fiber & flat washers

– Two 5/32˝threaded rods

– Two 5/32˝lockwashers

– Two knurled knobs

– Four wire connectors

– Ceiling Support Cable

with clamp

– Flat washer

– Lag bolt

– Allen wrench

– Chain coupler & chain fob

– Philips screwdriver, 4˝

Support Cable Bag

▲

WARNING

Do not install or use fan if any part is damaged or

missing. This product is designed to use only those

parts supplied with this product and/or any accessories

designated specifically for use with this product by

Fanimation. Substitution of parts or accessories not

designated for use with this product by Fanimation could

result in personal injury or property damage. Contact

your retail store for missing or damaged parts.

▲

WARNING

Before assembling your ceiling fan, refer to section on

proper method of wiring your fan (page 4). If you feel you

do not have enough wiring knowledge or experience,

have your fan installed by a licensed electrician.

Housing Switch Cup/

Adapter Assembly

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 Hz, 15 amp circuit. The

outlet box must be securely anchored and capable of

withstanding a load of at least 50 lbs. Figure 1 depicts

different structural configurations that may be used for

mounting the outlet box.

Ceiling

Joists

2˝x 4˝

Outlet

Box

Figure 1

If your fan is to replace an existing light fixture, turn

electricity off at the main fuse box at this time and remove

the existing light fixture.

▲

WARNING

To avoid fire or shock, follow all wiring instructions

carefully. Any electrical work not described in these

instructions should be done or approved by a licensed

electrician.

▲

WARNING

Turning off wall switch is not sufficent. To avoid

possible electrical shock, be sure electricity is turned

off at the main fuse box before wiring. All wiring must

be in accordance with National and Local codes and the

ceiling fan must be properly grounded as a precaution

against possible electrical shock.

▲

WARNING

To reduce the risk of fire, electrical shock, or personal

injury, mount fan to outlet box marked acceptable

for fan support of 22.7 kg (50 lbs) or less. Use screws

supplied with outlet box. Most outlet boxes commonly

used for support of light fixtures are not acceptable for

fan support and may need to be replaced. Consult a

qualified electrician if in doubt.

How to Assemble Your Ceiling Fan

Setscrew

Hanger

Ball

Figure 1

1. Remove the Hanger Ball by loosening the setscrew

in the Hanger Ball until the ball falls freely down the

Downrod. (Figure 1) Remove the Pin from the Downrod,

then remove the Hanger Ball. Retain the Pin and Hanger

Ball for reinstallation in Step 8.

2. The fan comes with blue, black, and white 80˝wires

and safety cable. Separate and untwist the three wires and

safety cable. Route the wires through the Downrod.

NOTE: You will be using either the 6˝downrod supplied with

your fan or an optional downrod purchased seperately.

3. Loosen the two setscrews in the Downrod Support. Align

the Clevis Pin holes in the Downrod with the holes in the

Downrod Support. Install the Clevis Pin and secure with

the Hairpin Clip. (Figure 3) Be sure to push the straight

leg of the hairpin clip through the hole near the end of the

clevis pin until the curved portion of the hairpin clip snaps

around the clevis pin. The hairpin clip must be properly

installed to prevent the clevis pin from working loose. Pull

on the Downrod to make sure the clevis pin is properly

installed.

NOTE: The setscrews must be properly installed as

described above, or fan-wobble could result.

4. Route wires and safety cable through opening in Canopy.

Position Canopy on fan shown with open side facing up.

(Figure 4)

5. Reinstall the Hanger Ball (Figure 2) on the Downrod

as follows. Route the three 80˝wires and safety cable

through the Hanger Ball. Position the Pin through the two

holes in the Downrod and align the Hanger Ball so the Pin

is captured in the groove in the top of the Hanger Ball. Pull

the Hanger Ball up tight against the pin. Securely tighten

the setscrew in the Hanger Ball. A loose setscrew

could create fan wobble.

Clevis

Setscrew (2)

Figure 2

Ceiling

Canopy

Setscrew

Downrod

Figure 3

Hairpin Clip

Downrod

Support

▲

WARNING

It is critical that the clevis pin in the downrod support

is properly installed and the setscrews are securely

tightened. Failure to verify that the pin and setscrews

are properly installed could result in the fan falling.

How to Assemble Your Ceiling Fan (cont’d)

6. While pulling up on the hanger ball, securely tighten

the two 3/16-24 x 3/8˝setscrews in the downrod support.

(Figure 3)

7. The fan comes with blue, black, and white leads. Before

installing fan, measure up approximately 6-9 inches above

top of Downrod/Hanger Ball Assembly. Cut off excess wire

and strip back insulation ½˝from end of wire.

8. You have now completed the upper assembly of your

new ceiling fan. You can now proceed with the hanging

and the electrical wiring of your fan.

Ceiling

Canopy

Downrod/Hanger

Ball Assembly

Figure 4

Ceiling Joist

Wood Member

(2˝x 4˝Approx.)

How to Hang Your Ceiling Fan

Figure 1

Floor

Ceiling

less than

7 ft

▲

WARNING

The fan must be hung with at least 7´ of clearance from

floor to blades (Figure 1)

▲

WARNING

The outlet box must be securely anchored and capable

of withstanding a load of at least 50 lbs. Hanger bracket

must seat ﬁrmly against outlet box. If the outlet box is

recessed, remove wallboard until bracket contacts box.

If bracket and/or outlet box are not securely attached,

the fan could wobble or fall.

CAUTION

Do not connect fan blades until the fan is completely

installed. Hanging fan with blades connected may result

in damage to the fan blades.

▲

WARNING

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or fire hazard.

▲

WARNING

To avoid possible shock, do not pinch wires between the

downrod/hanger ball assembly and the hanger bracket.

▲

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before hanging.

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

Figure 3

Figure 2

Junction

Box

Ceiling

Support

Cable Hanger Bracket

Ceiling

Downrod/Hanger

Ball Assembly

Attach

Safety Cable to

Ceiling Support

Cable

Tab

NOTE: Supply wires and

fan wires omitted for clarity

1. Using the 3⁄8˝x 2˝lag bolt and flat washer, attach

safety cable to ceiling joist or wood structural member.

The lag bolt will pass through the flat washer, safety

cable loop, the junction box and into the building structure

(Figure 2). You will first drill a ¼˝pilot hole into the

building structure to prevent splitting or cracking.

2. Securely attach the hanger bracket to ceiling junction

box acceptable for ceiling support.

NOTE: Ceiling support cable must be fastened between

flat washer and ceiling junction box (Figure 2).

3. Make sure the electrical supply wires, including the

hanger bracket grounding wire and safety cable are

pulled through the downrod, between the hanger bracket

and the junction box so that electrical connections can be

made later.

4. Carefully lift the fan and seat the downrod/hanger ball

assembly on the hanger bracket that was just attached to

the ceiling joist. Be sure the groove in the ball is lined up

with tab on the hanger bracket. (Figure 3)

5. Attach the safety cable to ceiling support cable. Slide

cable clamp onto safety cable (from fan). Place the end

of cable through the loop of ceiling support cable. Pull as

much cable through loop as possible. Feed end of cable

into clamp hole and firmly tighten screw (Figure 3). Cut

off excess safety cable.

How to Wire Your Ceiling Fan - Pull Chain

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a

licensed electrician.

1. Connect the green grounding lead from the hanger ball

and the green grounding lead from the hanger bracket to

the supply grounding conductor (this may be a bare wire

or wire with green colored insulation). Securely connect

wires with wire connectors supplied.

2. Securely connect the white fan motor wire to the white

supply (neutral) wire using wire connector supplied.

Securely connect the black fan motor wire and blue wire

to the black supply wire using wire connector supplied

(Figure 1).

3. After making the wire connections, the wires should

be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet

box and the ungrounded conductor on the other side of

the outlet box.

4. Secure the ceiling canopy to the hanger bracket with

threaded rods, external lockwashers, and knurled knobs

provided (see page 11).

Household

Supply

Listed

Outlet Box

Black

Green Wire

(Ground) from

Hanger Bracket

Green Wire

(Ground)

Black

Fan Wire

White

Blue

Green Wire

(Ground) from

Hanger Bowl

Figure 1

▲

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

▲

WARNING

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not operate

fan until the blades is in place. Noise and fan damage

could result.

Installing the Canopy Housing

1. Screw in two threaded rods into the Hanger Bracket

(Figure 1a).

NOTE: The threaded rods in the hanger bracket serves as

guides for easier installation.

2. Securely attach the Canopy Housing to the Hanger

Bracket using the external lockwashers and knurled knobs

supplied with your fan (Figure 1b).

Figure 1a Figure 1b

NOTE: Supply wires and fan wires omitted for clarity.

NOTE: This step is applicable after the neccessary wiring

is completed.

▲

WARNING

To avoid possible fire or shock, make sure that the

electrical wires are completely inside the canopy housing

and not pinched between the housing and the ceiling.

Assembling and Mounting the Fan Blades, & Adapter/Switch Hsg

NOTE: Shipping Support Plate MUST be removed prior to

assembling blades!

Blade & Blade Holder Assembly:

1. Lay the side of the blade holder on a flat surface with the

inside of the blade holder facing up. This is the side with

the threaded posts.

2. Position the wood blade over the blade holder with the

threaded posts showing. Make sure the bottom edge of

the blade is fully seated against the blade holder.

3. With a Philips screwdriver, tighten pan-head screws with

fiber, and flat washers to secure the blade. (Figure 1)

NOTE: The switch cap housing must be removed prior

to installing blade & blade holder assembly to the motor

hub.

4. Attach assembled blades and blade holders to the motor

hub using the provided screws. (Figure 2)

5. Make sure the screws securing the blade holders to the

motor hub are tight and that the blade holders are properly

seated.

Housing Switch Cup/Adapter Assembly:

6. Disassemble the Housing Switch Cup/Adapter assembly

by removing three screws. (Figure 3)

7. Assemble the Adapter assembly on the Housing Support

bracket and tighten three screws. (Figure 4)

8. Assemble the Adapter assembly on the Housing Support

bracket and tighten three screws. (Figure 4)

9. Securely attach the 9-pin switch cup connector to wiring

harness socket within Adapter assembly. (Figure 4)

Figure 2

Fan Blade

Screw

(2 per blade

holder)

Figure 1

Blade Holder

INSTALLATION NOTE

Do not connect fan blades until the fan is completely

installed. Installing the fan with blades assembled may

result in damage to the fan blades.

▲

WARNING

To reduce the risk of personal injury, do not bend the

blade holders when installing, balancing the blades or

cleaning the fan. Do not insert foreign objects in between

the rotating blades.

Figure 4

Figure 3

Maintenance

Periodic cleaning of your new ceiling fan is the only

maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth to

avoid scratching the ﬁnish.

Abrasive cleaning agents are not required and should be

avoided to prevent damage to ﬁnish.

CAUTION

Do not use water when cleaning your ceiling fan. It

could damage the motor or the blades and create the

possibility of electrical shock.

Operating Instructions - Pull Chain

Figure 2

Reversing

Switch

Speed Control

Pull Chain

1. Restore electrical power to the outlet box by turning the

electricity on at the main fuse box.

2. Check the operation of the fan by gently pulling on the

pull chain switch. (Figure 2)

3. If airflow is desired in the opposite direction, turn the

fan off and wait for the blades to stop turning. Then slide

the reverse switch to the opposite position and turn fan

on again. Your fan model is equipped with a 4-position,

3-speed, pull chain switch. The operating sequence is as

follows:

1st Pull = HIGH 3rd Pull = LOW

2nd Pull = MEDIUM 4th Pull = OFF

Figure 5

10. Assemble the Housing Switch Cup onto the assembled

Adapter with three screws. (Figure 5)

Restore Power and your fan is now wired to be turned on

and off from the fan pull chain speed control.

Assembling and Mounting the Fan Blades, & Adapter/Switch Hsg

Inhaltsverzeichnis

Andere Fanimation Lüfter Handbücher

Fanimation

Fanimation Air Shadow FB8250B Bedienungsanleitung

Fanimation

Fanimation KWARTET FPS8553 Series Bedienungsanleitung

Fanimation

Fanimation GLIDEAIRE FPD8520 Series Bedienungsanleitung

Fanimation

Fanimation The Edgewood TF610 Series Bedienungsanleitung

Fanimation

Fanimation The Odyn FPD8148 Bedienungsanleitung

Fanimation

Fanimation Huxley FP5620 Series Bedienungsanleitung

Fanimation

Fanimation FP4820PW The Cumulos Bedienungsanleitung

Fanimation

Fanimation FLORID LP8300 Series Bedienungsanleitung

Fanimation

Fanimation Louvre FP1320 Series Bedienungsanleitung

Fanimation

Fanimation FPD7943 Bedienungsanleitung

Fanimation

Fanimation The Edgewood TF721 Series Bedienungsanleitung

Fanimation

Fanimation Islander FP320 Series Bedienungsanleitung

Fanimation

Fanimation The Edgewood TF710 Series Bedienungsanleitung

Fanimation

Fanimation FP6252BN Bedienungsanleitung

Fanimation

Fanimation Escalade FP2320GZ Bedienungsanleitung

Fanimation

Fanimation FPD7617 Series Bedienungsanleitung

Fanimation

Fanimation The Zonix FP4640SN Bedienungsanleitung

Fanimation

Fanimation The Camhaven FP8095 Series Bedienungsanleitung

Fanimation

Fanimation Involution FP4520 Series Bedienungsanleitung

Fanimation

Fanimation SCULPTAIRE FP8511 Series Bedienungsanleitung

Fanimation

Fanimation Brewmaster FP10 Series Bedienungsanleitung

Fanimation

Fanimation Belleria FP4320 Series Bedienungsanleitung

Fanimation

Fanimation The Akira FP8000 Bedienungsanleitung

Fanimation

Fanimation Michael David's Adventure LB1820BL Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung