Fantec MR-35DRN Bedienungsanleitung

FANTEC

MR-35DRN

USER MANUAL

General Description

The FANTEC MR-35DRN is a fully functional gigabit NAS (Network Attached

Storage) with dual SATA interface. It provides superior performance and

functionality for Router Gateway, NAS, IP Set Top Box, VoIP and other SME

(Small and Medium Enterprise) and SOHO (Small Office / Home Office)

applications. The device has single 32-bit ARM9 RISC Processors with up to

800MIPS total performance and LINUX based Graphic User Interface (GUI). The

device integrates a full featured hardware crypto engine, two 10/100/1000Mbit/s

Ethernet RJ45 ports, dual USB2.0 host and dual SATA interface. The device also

includes an intelligent and programmable power management unit for portable

system applications.

1.0 HDD identification

For User who are not much familiar with LINUX based GUI, please take a look at

the following graph for better understanding of the hard disk identification. It will

help you to avoid the confusion of the disks.

1.0 Hard disk Identification....................................... 1

1.1 First commissioning............................................ 2

2.0 Operating MR-35DRN through GUI Chapter.......... 3

2.1 Set the MR-35DRN IP Address............................ 3

2.2 Administration of the MR-35DRN......................... 6

2.3 MR-35DRN Configuration................................... 6

2.4 .............................. 8

2.5 File settings....................................................... 9

2.6 File and Print settings......................................... 10

2.7 System setting................................................... 11

2.8 Network Service................................................. 15

2.9 Maintenance...................................................... 17

2.10 Log File........................................................... 19

2.11 Account........................................................... 19

2.12 Logout............................................................. 20

User and Group Management

3. Package content.................................................. 20

4. FAQ.................................................................... 20

Disk 1: is indicated by /dev/hdd Disk 2: is indicated by dev/hdc

‘IfaUSBpendriveor

alike is connected to

the MR-35DRN, the

Disk Utility overwiev,

recognizes a “ usb1”

device.

You can find it as a

share called “usb1”

under “My Network

Places”.

In RAID Setting

overwiev, the disks

are indicated from the

left to the right side.

First commissioning

Ready LED

Power LED

Power Button Reset

Connect the AC power Cable

Connect the LAN cable to the “LAN” port

Connect the SATA hard drive to P1 and P2

Press “Power” button for power ON/OFF

The MR-35DRN start-up will take about 3 minutes, during the boot

procedure the Ready LED is blinking; after the start-up is complete, the Ready

LED will flash permanent. Then you can access the MR-35DRN through the GUI.

(Graphic User Interface)

Note:

USB

WAN

USB

LAN

AC100-240V

Note:Sway from side to side the lock at the instructed point , which you could

open the doorknob to install/ unload the hard disk. In Contrast, when you sway from

side to side the lock at the instructed point , then you may not open it.

The Hard Disk Installation:Sway from side to side the lock , and pull the

doorknob to insert 1 or 2 hard disk.Close the doorknob and the installation will be

completed (The step will be represented in terms of following graphs)

2 Configuration FANTEC MR-35DRN by “SetupUtil.exe” and GUI

2.1 Set the MR-35DRN IP address

Note: Before you start to use the MR-35DRN, please connect the MR-35DRN’s

LAN port to your PC by network cable.

The MR-35DRN’s default IP is : 192.168.3.1;

So, you must set your PC’s network IP to192.168.3.X; (X=2.....254)

2 3

RESET

Please find the “SetupUtil.exe” configuration software from the CD,copy it to your

desktop and start it by double-click. Select the “Setup” button.

The MR-35DRN will be found in the “Selection”.Press the”OK” button.

Please Input the default password: “ , and press “OK”.admin”

Then you can change the MR-35DRN Name and IP address.

Press the “Next” button and you can set the Date and Time.

Note: Please don’t forget your IP address, otherwise you may loose all

information and are not able to access the MR-35DRN’s GUI !!!

Press the “Next” button and you can see the Setting Confirmation. Press the

“Save” button to complete the changes.

Internet Explorer 5.0 or later, Firefox 2.0 or later, Netscape Navigator 4.5 or later

is recommended to complete administrative task of MR-35DRN.

4 5

2.2 Administration of the MR-35DRN

admin

The following methods allows administrators to access the configuration pages.

Launch your web browser if you know the IP address of the MR-35DRN. Enter the

correct IP address in the browser. (in this example “http://192.168.10.110”)

Note: The MR-35DRN default IP is : 192.168.3.1

Enter the username and password into the login page. The username and

password by default for both is “ ”. The change of these access information

is recommended to gain security.

2.3 MR-35DRN Configuration

ATTENTION: If you have new, unformated disk please visit chapter

“2.3a Hard disk Setup” before starting the configuration of MR-35DRN.

Otherwise you will not be able to store any data on the device.

After login to the MR-35DRN by browser, there are 3 main selections:

“Basic”, “Control panel”, and “Personal Info” included and the related items

expansion list below .

2.3a Hard disk Setup

After login to the MR-35DRN by browser, the device will find new Disk and advise

you to format.

6 7

Please go to Maintenance and choose RAID Setting. Now you can select the

RAID mode that is equal to your requirements. You will start the operation by

pressing the “Create raid system” button. During the RAID building, the hard disk

will be formatted as well. After the format has finished the device is rebooting

ATTENTION: Due to the fact, that all settings are stored on the disk, you have to

reconfigure the device by the use of “SetupUtil.exe” from the desktop!!!

Afterwards you can access the GUI again.

For more information about the usage of the different RAID modes or how to

repair occurred damages, please refer to the FAQ chapter at page 20.

HDD is detected whether installed or not by system automatically. A new non-

formatted HDD was found, formatting hard drive is suggested by the pop up

window. And the system will restart after format complete automatically. If a

formatted HDD is found, then the system gets user information from HDD.

Quick Setup

To modify the language support in web page, please follow the instruction below

To add user support, select the “Add User” chapter for setting. Please refer to

“Users and Groups” chapter for more detail.

To add group support, select the “Add Group” chapter for setting. Please refer to

“Users and Groups” chapter for more detail.

To add folder sharing support, select the “Add Share” chapter for setting. Please

refer to “Share Management” chapter for more detail.

2.4 User and Group Management

In User Management menu, it shows all existing users in the system. A new user

is created by filling out the form and click “Save” button. To delete a specified

user, you need to select the existing user and click “Delete User” button. Click

“Group” button to enter the Group management menu.

In Group Management menu, it shows all existing groups in the system. A new

group is created by filling out the form and click “Save” button. Select the existing

group name and click “Delete Group” button to delete a specified group. Add or

Remove users from an existing group can be done by highlighting the group name

and click “Members” button.

2.5 File

Three sections are included in “File and Print”, which are “File server”, “Share

Management”, and “Printer server”.

8 9

The “Disk spin

down time”

allows you to

enable the

energy-saving

mode. The disks

will spin down

after the

appointed time,

if no access to

the MR-35DRN

is in progress.

Please follow the

steps1to6from

the “Wizard” to

configure the

MR-35DRN in

quick mode. If

you don’t use a

DNS Server

(step 4/6) please

enter 0.0.0.0 to

the input mask.

2.6 File and Print

2.6.1 File Server

Windows Setting

FTP Server setting

NFS Server Setting

Guest Access Setting

2.6.2 Share Management

Click “Enable” check box to enable Microsoft Windows connection

Set Workgroup name for Windows client to access

Define Windows Internet Name Server IP address

Click “Enable” box to enable FTP server function, and default port 21.

Click “Enable” box to enable NFS server function

Click “Enable” box to allow user using guest-share folder and guest-user set

upload quota (Mega Bytes)

It shows all existing shares. “public” is the factory default share located at system

/shares/public directory.

Create Share

Property Change

Windows and FTP Access

NFS Access

Delete Share

Press “Save” button, after fill in “Share name” and “Path” box, will create a new

share.

Click a share in “Existing Shares” box could modify property of the share. Press

“Windows, FTP Access” or “NFS Access” button could set or remove read/write

permission of the share.

“Allow for all” is to allow all users to access the shared storage in the server; or

you may specify User/Group name in Access box and select “Read Only” or

Writable permission to the User/Group.

You could check “Allow for all” to allow all clients access NFS server. Or add client

PCs IP address/Subnet mask to the permission list to allow only permission list to

access the NFS server.

“Delete Share” deletes a specified share.

(Use “Start” , “Run” and

input \\192.168.3.1 to

locate all existing shares.

According to the sample

you have to enter

“\\192.168.10.110”.

2.7 System setting

2.7.1 LAN Settings

Hostname

IP address setting

There are eight sections are included in “System Setting”, which are “LAN

Settings”, “WAN Settings”, “DDNS”, “Qos”, ”Time Settings”, “Turn Off Server”,

“Information”, “Disk Usage”, and “Error Notification”.

You must assign a unique name for each MR-35DRN as the identification within

your local area network. The default hostname is “fantec”.

You must assign a unique IP address for each MR-35DRN as the identification

within your local area network. The default IP address is “192.168.3.1”.

2.6.3 Printer Server

Check Printer Server “Enable” box to enable Print Server functions.

To add a new printer

in your printer

management please

enter following URL

to the input mask of

your operating

system:

“\\192.168.3.1\lp”.

According to the

sample you have to

entrer:

“\\192.168.10.110\lp”

2.7.2 WAN Settings

The WAN port can connect the internet or external local area network. Note: the

IP address of LAN and WAN can not in the same paragraph!!!

For example, the WAN IP address is: 192.168. . X, then the LAN IP address could

not be: 192.168.1. X, but should be: 192.168. . X, or 192.168. . X or

192.168. .X according to the sample.

Use static IP address

DHCP

Use PPPOE Obtain the IP addresses

Acquire a unique IP address, Subnet mask, and Default gateway information

from your network system administrator.

The system obtains the IP address automatically via DHCP protocol if the

external local network has DHCP server available. Press the <Refresh IP>,and

save it.Obtain DNS server address automatically. The system gets DNS server

addresses from DHCP server if available

The MR-35DRN provides superior performance and functionality for Router

Gateway. You can get the User Name and password from your

Telecommunications providers.

2.7.3 DDNS

2.7.4 Qos

Note:

DDNS(Dynamic DNS) service allows you to assign a fixed domain name to a

dynamic WAN IP address. This allows you to host your own Web, FTP or other

type of TCP/IP server in your LAN. Before configuring DDNS, you need to visit

www.dyndns.com and register a domain name. (The DDNS service is provided by

DynDNS.org

)

Quality of Service (QoS) refers to the capability of a network to provide better

service to selected network traffic over various technologies. The primary goal of

QoS is to provide priority and improved loss characteristics. Also important is

making sure that providing priority for one or more flows does not make other

flows fail.

This function is only suitable for professional Administrators.

2.7.5 Time Setting

2.7.6 Restart Server

Set current Date, Time and Time zone.

Specify NTP server if you want to get Date and Time from time server.

To restart the server, click the “Restart” button.

12 13

2.7.7 Information

Display system information, such as:

2.7.8 Disk Usage

Collect and displays all HDDs usage summary and user's quota information.

2.7.9 Error Notification

Disk Usage

Windows File Sharing Server

FTP Server

DHCP Server

Check Interval

Monitoring Services Setting:

If the disk usage reaches 90%, the system will inform the administrator this

message.

If the samba task has any problem, the system will inform the administrator this

message.

If the FTP Server task has any problem, the system will inform the administrator

this message.

If the DHCP Server task has any problem, the system will inform the administrator

this message

You can select the system informed interval to hourly or daily.

2.8 Network Service

2.8.1 DHCP Server

The DHCP service allows your PC to get an IP address from the MR-35DRN.

If your PC can not get an IP address from the NAS, you should set your PC IP

address to a static IP address.

14 15

Email Notification Setting:

Error Handling Mail Server

Error Handling Email Addresses

Pop-Up Notification Setting:

Error Handling Pop-Up Machines

Enable

Enable notification method by an email.

Specify your email host name.

Specify administrator email address.

Enable

Enable notification method by Windows pop-up messages.

Specify administrator PC IP address.

Note: Administrator

2.8.3 Virtual Server

2.8.4 ALG

2.8.5 Access Control

These 3 functions below is only suitable for professional .

2.9 Maintenance

2.9.1 Disk Utility

Six sections are included in Maintenance. There are “Disk Utility”, “RAID

Setting”,“Firmware Upgrade”, “Save Configuration”, “Restore Configuration” and

“Factory Reset”.

Disk utility shows device name, type of file system, total disk size, used disk size,

volume mounted, and disk mount status of all disks.

For new attached hard disk, you should format the HDD before any setting.

To avoid pressing the button by mistake, the system will acquire your confirmation

before starting “Format” or “Scandisk” function.

The format and scan procedure will take a few moments.Please be patient until

the progress has finished.

Encrypt Box

Format Button

Scan Button

Detail Button

Refresh button

Disk spin down time

2.9.2 RAID Setting

Rebuild button

The MR-35DRN supports 128 bits loop-AES encryption of EXT2 file system. If you

want to turn on this function, you should input 20 characters password and format

disk again. (If a RAID is used, this function is disabled)

This is used to format the specified disk. The device supports three types of file

system: “EXT2”, “EXT3” and “FAT32”. (If a RAID is used, this function is disabled)

This is used to check the disk integrity. (If a RAID is used, this function is

disabled)

If the hard disk supports S.M.A.R.T, it will report the disk health status.

This is used to refresh hard driver status.

Specify your disk spin down time if no access to the hard disks.

The MR-35DRN supports RAID mode 0, 1 and Linear. You only have to plug in 2

hard disks and the RAID function can be used. To create the RAID system please

format the hard disks and select EXT2 or EXT3 file system and RAID 0, 1 or

Linear RAID mode.

This is used to rebuild raid file system after replacement of a broken hard disk.

16 17

2.8.2 Bonjour

THE MR-35DRN supports Apple Bonjour protocol and Apple iTunes server.

Check Enable box could enable Bonjour protocol.

Check iTunes Enable box could enable iTunes server.

All MP3 music files should be storedt in “/public/music” folder through samba or

ftp protocol, then client PC can search “fantec_Music_Box” with iTunes and play

music. The iTunes software can be downloaded from Apple.com website.

Inhaltsverzeichnis

Andere Fantec Netzwerk-Hardware Handbücher

Fantec

Fantec MR-35DUF Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung