Fanvil H2S Bedienungsanleitung

Hotel Phone - H2S

Quick Installation Guide

2 / 6

Connection methods

Please connect power adapter, network, PC, and handset to the corresponding ports as described in

below picture.

Wall mount setup

Fix the device on the wall.

Screw the embedded junction box on the wall

Connect the cable from embedded junction box to the telephone.

Hitch the telephone on the screw.

Please refer the dimension, when you want to install it on the wall.

3 / 6

1 Introduction to the Phone User Interface

1.1 Keypad

The above picture shows the keypad layout of the device. Each key provides its own specific function.

User should refer to the illustration in this section about the usage of each key and the description in this

document about each function.

Hold key - You could hold a call by pressing the key.

Transfer key - You could transfer a call by pressing the key.

Standard Telephone Keys - The 12 standard telephone keys provide the same function as standard

telephones

Volume -/+ - By pressing ‘Volume -/+’ button, user can adjust the volume.

Redial - By pressing ‘Redial’ button, user can redial the last dialed number.

Ringing Light - When there is a call ringing, the ringing lights will flicker, only when the

speakerphone ring volume is 8 and 9.

Working Light - When you pick up the handset, the working light will be lit.

Power Light - When the device is power on, the power light will be lit.

Transfer key

Volume Control

Receiver

Hold key

Redial

MIC

Standard

Telephone Keys

Power Light

Working Light

Ringing Light

4 / 6

2 Phone Settings

In order to get the device ready for making and receiving phone calls, the device must be configured with

correct network configurations and with an SIP telephony service.

The SIP must be configured properly to be able to provide telephony service.

2.1 Getting IP address

DHCP is the default setting in Network, and telephone will get the IP address from DHCP server(Router)

after the line connected.

There are three common IP configuration modes.

Dynamic Host Configuration Protocol (DHCP) – This is the automatic configuration mode by getting

network configurations from a DHCP server. Users need not to configure any parameters manually. All

configuration parameters will be getting from DHCP server and applied to the device. This is

recommended for most users.

Static IP Configuration – This option allows user to configure each IP parameters manually, including IP

Address, Subnet Mask, Default Gateway, and DNS servers. This is usually used in an office environment

or by professional users.

PPPoE – This option is often used by users who connect the device to a broadband modem or router. To

establish a PPPoE connection, user should configure username and password provided by the service

provider.

2.2 Checking IP address

Pick up the handset, please input “# * 111” button or Long press "#" button, then you can hear the IP

address voice information.

2.3 How to enter into web setting interface

Set the telephone through web interface.

Connect the telephone and PC in the same LAN.

Run the IE in the PC, and input the telephone IP in address bar.

Input the User name and password, Default Username/Password: admin.

Click “logon” button to enter into the web setting interface.

5 / 6

2.4 SIP Setting

Enter into the web setting interface, select Line->SIP, and fill in the items below.

Server Address

Account Name

Phone Number

Password

Click the Apply button to save the Configuration, that you can make a call after the SIP registration is

successful.

6 / 6

3 Basic Operation

3.1 Making call

There using dial pad to make a call.

Lift the handset.

Dial the number on the dial pad, end with # as default.

End a call, hang up handset.

3.2 Answering call

When your telephone rings and the light flashes.

Lift the handset and start to talk.

End a call, hang up handset.

3.3 Holding call

While on a call, press the “Hold” key.

To retrieve a held call, press the “Hold” key again.

3.4 Redialing

Press redial to dial the last number you dialed.

Lift handset.

Press Redial to dial the last number you dialed.

3.5 Transfer Call

To perform a blind transfer:

During a call, press Transfer. The active call is held.

From the Dialer, place a call to the person you want to transfer the call to.

Press“#” or “Transfer” button. The call automatically transfers to the person you specified.

To transfer a call:

During a call, press Transfer. The active call is held.

From the Dialer, place a call to the person you want to transfer the call to.

Press “Redial” button. the second call connected, and you can talk with the person.

Press “Transfer” button. The call automatically transfers to the person you specified.

Andere Handbücher für H2S

Inhaltsverzeichnis

Andere Fanvil IP-Telefon Handbücher

Fanvil

Fanvil V67 Bedienungsanleitung

Fanvil

Fanvil F52 Bedienungsanleitung

Fanvil

Fanvil D900 Bedienungsanleitung

Fanvil

Fanvil X5S Bedienungsanleitung

Fanvil

Fanvil X2CP Bedienungsanleitung

Fanvil

Fanvil F52 Bedienungsanleitung

Fanvil

Fanvil D800 Bedienungsanleitung

Fanvil

Fanvil C62 Bedienungsanleitung

Fanvil

Fanvil X3SG Pro Bedienungsanleitung

Fanvil

Fanvil X7A Bedienungsanleitung

Fanvil

Fanvil X3U Pro Bedienungsanleitung

Fanvil

Fanvil X5 Bedienungsanleitung

Fanvil

Fanvil V64 Bedienungsanleitung

Fanvil

Fanvil X210 Bedienungsanleitung

Fanvil

Fanvil X6 Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Fanvil

Fanvil X4U Bedienungsanleitung

Fanvil

Fanvil X3S Basic Kurzanleitung

Fanvil

Fanvil X5U V2 Bedienungsanleitung

Fanvil

Fanvil BW206 Betriebshandbuch

Fanvil

Fanvil X7 Bedienungsanleitung

Fanvil

Fanvil C600 Bedienungsanleitung

Fanvil

Fanvil H3 Bedienungsanleitung

Fanvil

Fanvil H5 Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung