FBII XL-2T Bedienungsanleitung

L-

-2

Security System

User Guide

N9819V3 2/00

FIRE BURGLARY INSTRUMENTS,

INC.

- 2-

Table Of Contents

QUICK REFERENCE.......................................................................................................................3

INTRODUCTION............................................................................................................................5

SYSTEM REFERENCE...................................................................................................................6

TURNING THE SYSTEM ON........................................................................................................9

TURNING THE SYSTEM OFF....................................................................................................12

USER CODES.................................................................................................................................13

MISCELLANEOUS COMMANDS.............................................................................................14

TESTING THE SYSTEM..............................................................................................................16

NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE

DETECTORS..................................................................................................................................17

EMERGENCY EVACUATION.....................................................................................................18

GLOSSARY....................................................................................................................................20

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT............................23

TELEPHONE OPERATIONAL PROBLEMS...........................................................................23

LIMITATIONS OF THIS ALARM SYSTEM............................................................................25

LIMITED WARRANTY................................................................................................................28

- 3-

Quick Reference

TO TURN SYSTEM ON

1. Check to make sure the system is ready, (Green READY light is

lit†).

2. Enter your 4-digit user code.

3. Exit through a door designated by your installer as an exit/entry

door.

4. The ON/OFF (ARM) light will light.

TO TURN SYSTEM OFF

1. Enter through a door designated by your installer as an exit/entry

door

2. Enter your 4-digit user code.

3. The system ON (ARM) light will go out.

TO TURN SYSTEM ON AND STAY INSIDE

1. Check to make sure the system is ready (Green READY light is

lit†).

2. Press STAY .

3. Enter your user code.

The ON/OFF (ARM) light and the STAY light will both light.

REMEMBER: You must turn the system OFF if you want to open the door

or leave the premises after the exit time has passed.

TO TURN THE SYSTEM ON: INSTANT MODE, AND STAY INSIDE

1. Check to make sure the system is ready (Green READY light is

lit†).

2. Press INSTANT .

3. Press STAY .

4. Enter your user code.

- 4-

The ON/OFF (ARM) light, the INSTANT light, and the STAY light will

all be on.

TO RESET SMOKE DETECTOR

1. Enter your 4-digit user code.

=READY light is not available on all keypads.

- 5-

Introduction

Congratulations on your decision to protect your home or business

with the XL-2T security system. You have chosen a reliable, state-

of-the-art security system that is remarkably easy to operate. Your

system has been professionally installed by your local Security

Company whose representative can explain the specifics of your

system.

The keypad is the input and display device for your security system.

Your Security Company representative will suggest the model most

appropriate for your premises and your needs.

The XL-2T is listed by Underwriters Laboratories for Household

Fire and Burglary applications.

Throughout this manual, the following conventions are used to

represent the keystrokes required to perform the following

functions.

STAY Press button labeled STAY.

BYPASS Press button labeled BYPASS.

INSTANT Press button labeled INSTANT.

CODE Press button labeled CODE.

Enter 4-digit user code.

Please keep your manual in a convenient location so you can

refer to it if needed.

- 6-

System Reference

ZONE DESCRIPTIONS

In the following table, enter a description of the area of protection

for each zone.

Example: Zone 1 Windows on North side of building

Zone 4 Main entrance to building.

ZONE DESCRIPTION

2 _______________________________________

Entry time ________ Door __________ Exit time ________

Entry time ________ Door __________

Exit time is the same for all designated Entry/Exit doors.

SEND-HELP ALERT

All keypads are equipped with emergency-pair keys. In order

to activate the alert, both keys must be pressed at the same

time. The type of keypad you have installed dictates which keys you

press. Your installer will show you how to activate these emergency

keys. The emergency keys used for all keypads are shown below.

The following SEND - HELP ALERT is programmed into my

system:

KEYS DESCRIPTION

[#] & [QQ ] (Right=)__________________________________

[7] & [9] (Left=)__________________________________

[1] & [3] (Center=)__________________________________

- 7-

=Buttons on XL-4600SM keypad only

- 8-

System Reference (cont)

USER CODE ASSIGNMENTS

In the following table, enter the names of the individuals assigned

to each specific User ID number.

USER ID ASSIGNED TO

1(MASTER USER * )

2(MASTER USER * )

4**

13 Door Strike - Yes No If No

______________________

(If user 13 is not assigned to door strike, then any user can

activate the door strike.)

14 Only Turns System ON -Yes If No

__________________

15 Ambush/Duress Code -Yes If No

___________________

* Master Users can add, change, or erase other user codes.

** If your installer enables only User 4 to report openings and closings to the

CS, then only those person(s) that you assign User 4 ID to will cause a report

to be generated.

MONITORING STATION INFORMATION

- 9-

Account #

Telephone #

Turning The System On

IS THE SYSTEM READY?

You can turn the burglar portion of your security system ON and OFF. Before

you can turn the system ON, it must be “ready.” If you have a protected door

open, or someone is moving in view of a motion detector, the system will not

display “READY.”

The system is ready if the READY light is ON or if the display shows:

SYSTEM READY

WHEN SYSTEM IS NOT READY

If the system is not ready to be armed, the READY light will be OFF and the

zone lights will show which zone or zones are not ready. The following

conditions will be indicated by the zone lights or described on the display:

Fast Blink ...................................Alarm

Slow Blink/Low Intensity .........Bypass

Slow Pulse ..................................Trouble

Solid ON .....................................Not Ready

Example: If the READY light is not lit and the Zone 1light is solid ON, an

alarm sensor on Zone 1 is faulted. This might mean that a door is open or

someone is walking in view of a motion sensor. Check all sensors on Zone 1 and

resolve the problem. When all sensors are restored, the READY light will come

ON and the zone light will go out. In this example, the display shows:

SYSTEM NOT READY

Determine which zone or zones are not ready, resolve the problem, and turn the

system ON normally. If the problem cannot be resolved, you may bypass the

zone that is not ready. Bypassing should only be done if the problem on the zone

cannot be resolved, OR if you intentionally wish to leave the zone OFF.

For example, you would leave the zone OFF if you plan to keep the window open

for ventilation. Zones that are bypassed are not protected when the

system is ON. See Bypass on the following page for a description of the

procedure.

and NOT RDY ZONE 1

FRONT DOOR

- 10 -

Turning The System ON (cont)

TO TURN SYSTEM ON AND LEAVE

Enter your 4-digit user code.

The System ON, (ARM) light will go ON or the display will show:

ON: AWAY ........

Exit through a door designated by your installer as an exit/entry door. You must

leave within the exit time programmed by your installer. Refer to the reference

sheet for the time that has been set for your system.

TO TURN SYSTEM ON AND STAY INSIDE

To turn the perimeter portion of your burglar alarm ON and move around freely

inside the premises, use the STAY mode.

Check to make sure the system is ready. When it is ready, press:

STAY followed by your user code.

When the system has been turned on successfully, the ON/OFF (ARM) light

and the STAY light will be lit, or the LCD will display:

ON: STAY

REMEMBER: You must turn the system OFF if you want to open the door or

leave the premises after the exit time has passed.

TO TURN SYSTEM ON IN INSTANT MODE AND STAY INSIDE

In INSTANT STAY mode, the perimeter portion of your burglar alarm system

is ON and the time delays are eliminated from your normal Entry/Exit door(s).

All interior protection is OFF, so you are free to move around inside.

Check to make sure the system is READY. When it is ready, press:

INSTANT followed by

STAY followed by your user code.

When the system has been turned ON successfully, the ON/OFF (ARM) light,

the INSTANT light, and the STAY light will all be ON, or the LCD will

display:

ON: STAY INSTANT

Andere Handbücher für XL-2T

Inhaltsverzeichnis

Andere FBII Sicherheitssystem Handbücher

FBII

FBII XL-20 Bedienungsanleitung

FBII

FBII XL-2P Bedienungsanleitung

FBII

FBII XL-2T Montageanleitung

FBII

FBII XL-5 Bedienungsanleitung

FBII

FBII XL-21 Bedienungsanleitung

FBII

FBII XL-2T Montageanleitung

FBII

FBII XL4600DL Bedienungsanleitung

FBII

FBII Omni-408A Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

FBII

FBII XL-2 Platinum Bedienungsanleitung

FBII

FBII OMNI-600EU Bedienungsanleitung

FBII

FBII XL-2T Montageanleitung

FBII

FBII LEGEND 7100 Bedienungsanleitung

FBII

FBII XL-4B Bedienungsanleitung

FBII

FBII XL-2S Silver Bedienungsanleitung

FBII

FBII XL-21 Bedienungsanleitung

FBII

FBII XL-1 Bedienungsanleitung

FBII

FBII Star XL4800 EZ Bedienungsanleitung

FBII

FBII XL-2P Bedienungsanleitung

FBII

FBII XL-2 Bedienungsanleitung

FBII

FBII OMNI-400 EU Montageanleitung

FBII

FBII OMNI-848EU Bedienungsanleitung

FBII

FBII OMNI-848 Bedienungsanleitung

FBII

FBII XL-1S Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung