Federal Signal Corporation I-IPTEL1 Stücklistenhandbuch

25500823

Rev. A1 0123

Printed in U.S.A.

Description, Installation, and

Conguration Manual

IP Phone for

Intelligent Systems

Model: I-IPTEL1

Limited Warranty

This product is subject to and covered by a limited warranty, a

copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal

Drive, University Park, IL 60484, email to [email protected] or call

+1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of ﬁtness for a particular

purpose and any warranty against failure of its essential

purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support 800-548-7229 • +1 708 534-3400

Technical Support 800-524-3021 • +1 708 534-3400

All product names or trademarks are properties of their respective owners.

Description, Installation, and Conguration Manual

Federal Signal www.fedsig.com

Contents

Safety Messages.............................................................................................4

General Description .......................................................................................4

Features....................................................................................................5

Applications...............................................................................................6

Overview ..................................................................................................7

Unpacking the Device ....................................................................................8

Specications .................................................................................................8

Introduction of the Keypad............................................................................9

Connecting the IP Phone.............................................................................14

Conguring the Network Interface..............................................................15

Conguring Static Settings......................................................................18

Conguring DHCP Settings ....................................................................19

Conguring PPPoE Settings...................................................................19

Conguring SIP Settings.........................................................................20

Basic Setting.................................................................................................20

Language setting ....................................................................................20

Making a call...........................................................................................21

Accepting a call.......................................................................................21

Placing a call on hold..............................................................................21

Three-party conference...........................................................................21

Call transfer.............................................................................................22

Call forward.............................................................................................22

Call mute.................................................................................................22

Call list ....................................................................................................22

Phonebook..............................................................................................23

Programmable keys................................................................................23

Redial......................................................................................................23

Do not disturb..........................................................................................23

Voice mail................................................................................................23

Bluetooth.................................................................................................24

Wi-Fi........................................................................................................24

Getting Service .............................................................................................24

Figures

Keypad of IP Phone.......................................................................................9

Connecting to the Device ...........................................................................14

Typical IP Phone Setup ...............................................................................15

Safety Messages

IP Phone for Intelligent Systems (I-IPTEL1)

Federal Signal www.fedsig.com

Safety Messages

It is important to follow all instructions shipped with this

product. Before you work on any equipment, be aware of the

hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents.

After installation, test the system to conﬁrm that it is operating

properly. Test the system regularly to conﬁrm that it will be

operational in an emergency. For a complete list of safety

messages, see the IP Phone for Intelligent Systems User Manual

(part number 25500824). See fedsig.com for online manuals.

General Description

The IP phone can multicast live PA directly to a multicast group

of speakers and then multicast DTMF control commands to

activate pre-recorded voice messages or siren tones stored

within the speakers. Include the IP phone on an existing SIP

phone system or LAN, or deploy the phones and speakers on a

separate LAN/VLAN dedicated for emergency or frequent VoIP

use. The IP phone supports RTP multicast and DTMF activation

of pre-recorded siren tones/pre-recorded voice messages on

the Federal Signal IP series of devices.

It is easy to conﬁgure the phone with preset buttons to provide

one-touch dialing and pre-conﬁgured speaker activations. When

used with the Federal Signal line of IP-based speakers, you can

conﬁgure a low-cost alerting system for industrial and campus

environments. An IP phone can call individual speakers for live

Public Addresses and then use a DTMF keypad to activate pre-

recorded voice or siren tones.

The phone can multicast live PA directly to a multicast group

of speakers and then multicast DTMF control commands to

speakers to activate pre-recorded voice messages or siren

tones to an unlimited number of speakers simultaneously.

This allows the creation of zones for wide areas or speciﬁc

notiﬁcation groups. You can use multiple phones to create

multi-location control and activation points. The phones can

General Description

Description, Installation, and Conguration Manual

Federal Signal www.fedsig.com

also be conﬁgured to allow direct SIP calls between phones and

speakers without a SIP server.

Power the phone via PoE or from an (included) external power

supply. The IP phone has three color displays for ease of use.

You can conﬁgure each button for name and color. The phone

has high-deﬁnition audio on the handset and speaker phone.

The phone is conﬁgurable for 19 dierent languages.

The Federal Signal line of Informer IP Speakers includes an

internal SD card and ampliﬁer to deliver tone warnings and

intelligible voice messages from locally stored memory, enabling

autonomous operation from contact closures and single button

controls from the I-IPTEL1 phones. The Informer IP Speaker also

has remote volume control for optimizing sound levels across

your alerting area. The remote volume control also includes

an ambient-noise-monitoring capability to adjust volume

automatically depending on external noise levels.

Informer IP Speaker allows connecting up to four external

switches to activate predeﬁned alert events. You can program

and conﬁgure the Informer IP Speaker as a standalone device

to only use the inputs for activation. This may be useful if the

location has no network connectivity but where voice and tone

alerts from locally activated inputs are required. The Informer IP

Speaker can be networked later for additional functionality.

Features

The I-IPTEL1 has the following features.

• Over 60 programmable buttons

• Phone-to-phone and phone-speaker dialing without a SIP

Server

• Phone-to-speaker for live PA

• Direct SIP calling and multicast paging

• Ability to activate pre-recorded voice messages or siren

tones

General Description

IP Phone for Intelligent Systems (I-IPTEL1)

Federal Signal www.fedsig.com

• Fully functional with Informer15 and Informer100 Speakers

• Static IP or DHCP

• Supports LLDP, CDP, DHCP VLAN, VLAN Custom Options,

QoS, WAN VLAN, and 8021x

• Conﬁgurable from Web User Interface

• Multicast DTMF to control Federal Signal’s IP products

• Desktop stand

• Ability to synchronize with Network Time Protocol (NTP)

clock

Applications

The I-IPTEL1 has the following applications.

• Indoor and outdoor speaker locations

• Muster or call stations

• Campuses or school alerting

• Use with video security systems

• Plant wide live-PA announcements

• Loud industrial facilities

• Weather alerting

• Food processing locations

• Plant wide alerting system

General Description

Description, Installation, and Conguration Manual

Federal Signal www.fedsig.com

Table 1 Ordering Information

Model Description

I-IPTEL1 IP Phone with 60 programmable buttons

I-IP15 15 W PoE+ indoor/outdoor speaker

I-IP100 100 W indoor/outdoor speaker

I-IPIO* 1/2 W desktop speaker

I-IPW* 1/2 W wall mount speaker

I-IP2* Two-channel 1/2 W audio outputs module

I-IPSIU* I/O module with 16 contact inputs, 8 contact outputs,

1/2 W audio output

*Requires Series C Model.

See www.fedsig.com for additional product information.

Overview

Use the IP Phone with the Federal Signal line of IP-based

speakers. The Federal Signal Informer series IP products

incorporate industry-standard Web, SIP phone, IP Multicast, and

Modbus®PLC interfaces to simplify integration with existing

systems. Each Informer device has its own Installation Manual.

The IP Phone can be used with the Federal Signal model UVRI-B

Alarm Control and Fire Alarm interface and the following list of

Federal Signal Informer series IP products:

• Informer-IP Desk Mount (I-IP-IO)

• Informer-IP Wall Mount (I-IPW)

• Informer15 Speaker (I-IP15)

• Informer100 Speaker (I-IP100AC and I-IP100DC)

• Informer-PA for Public Address Interface (I-IP2)

• Informer Sensor Interface Unit (I-IPSIU)

Unpacking the Device

IP Phone for Intelligent Systems (I-IPTEL1)

Federal Signal www.fedsig.com

Unpacking the Device

Ensure that the parts listed are included in the package. If you

are missing any parts, contact Customer Support.

The following is a list of the contents:

• IP Phone

• Handset

• Handset Cord

• Ethernet Cable

• Stand

• Power Adapter

Specications

Table 2 Specications

Physical LAN Port: Physical: 10/100/1000 Mbps

Ethernet, dual bridged port for PC

bypass

IP Conguration Static IP / DHCP

Power Consumption (PoE) 10.46 W maximum

Power Consumption

(AC Adapter)

9.13 W maximum

DC Power Input 5 V / 2 A max

Operating temperature range 32°F to 113°F (0°C to 45°C)

Working Humidity Up to 95%, non-condensing

Installation Desktop Stand

Handset/Hands-free-/Headset

mode

Device Dimensions Desktop Stand (Angles 1):

9.4 x 7.8 x 7.3 inches

(239 x 199.3 x 185.8 mm)

Desktop Stand (Angles 2):

9.4 x 7.4 x 7.7 inches

(239 x 188.5 x 195.6 mm)

Introduction of the Keypad

Description, Installation, and Conguration Manual

Federal Signal www.fedsig.com

Introduction of the Keypad

The following ﬁgure illustrates the front view and the keypad of

the IP Phone, and the table describes the keys.

Figure 1 Keypad of IP Phone

15 16 17 12 13

18 1

Introduction of the Keypad

IP Phone for Intelligent Systems (I-IPTEL1)

Federal Signal www.fedsig.com

Table 3 Keypad Description

No. Interface Description

1 Soft-menu

Buttons

These four buttons provide different functions

corresponding to the soft menu displayed on

the screen.

2Hold Key Press the Hold key during the call to hold the

call, and press it again to cancel the hold.

3 Transfer

Key

Press the Transfer button to transfer the current

call to other numbers.

4 Conference Press the Conference button to initiate a three-

party conference.

5Navigate/

Keys

Press the up/down navigation key to change

the line or move the cursor in the screen list.

On some settings and text editing pages, you

can press the left/right navigation key to change

options or move the cursor in the screen list to

the left/right. OK key: the default is equivalent

to soft button conrmation; you can customize.

6Contact Key Press the Contact key to enter the phone book

interface and select the person to call.

7 Call Log

Key

Press the Call Log key to see the incoming/

outgoing calls.

8 Standard

Telephone

Keys

The 12 standard telephone keys provide the

same function as standard telephones; some

keys also provide a special function by long

pressing the key. (To long press, press and hold

the button for more than 2 seconds.)

Long press the lock key to lock the keypad.

Enter the PIN to unlock the keypad.

9 Voice Mail Press the Voice Mail key to enter the interface

of SMS and the voice mail list.

10 Headset

Key

Press the Headset key to open the headset

channel.

Andere Handbücher für I-IPTEL1

Inhaltsverzeichnis

Andere Federal Signal Corporation IP-Telefon Handbücher

Federal Signal Corporation

Federal Signal Corporation I-IPTEL1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation FT200C-V Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung