Feig Electronic OBID i-scan ID ISC.M02.M8-B Bedienungsanleitung

INSTALLATION MANUAL

final –public (B)

2013-02-18 –M90402-1e-ID-B

ID ISC.M02.M8-B

(English)

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 2 of 15

M90402-1e-ID-B

Note

FEIG ELECTRONIC GmbH

Lange Strasse 4

D-35781 Weilburg-Waldhausen

Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are

forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved

in the event of the grant of a patent or the registration of a utility model or design.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments and does not give

any guaranty for the functionality of the complete system which incorporates the subject of this document.

FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed

with components and testing methods for a level of reliability suitable for use in or in connection with surgical

implants or as critical components in any life support systems whose failure to perform can reasonably be

expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application

designer must take reasonably prudent steps to protect against system failures.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-

ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does

not convey any license under its patent rights nor the rights of others.

OBID®and OBID i-scan®is a registered trademark of FEIG ELECTRONIC GmbH.

All brand names, trademarks or logos are property of their respective owners.

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 3 of 15

M90402-1e-ID-B

Content

ID ISC.M02.M8-B 1

1Safety Instructions / Warning - Read before start-up ! 4

2Performance Characteristics of the ID ISC.M02.M8-B Reader Module 5

2.1 Performance Characteristics................................................................................. 5

2.2 Available module....................................................................................................5

3Installation and wiring 6

3.1 Dimensions.............................................................................................................6

3.2 Wiring......................................................................................................................7

3.2.1 Supply voltage..........................................................................................................7

3.2.2 RS232-LVTTL-Interface (3,3V).................................................................................8

3.2.3 Connection of the external antennas........................................................................9

3.3 Installation notes.................................................................................................. 10

3.3.1 Mounting................................................................................................................10

3.3.2 Influence ................................................................................................................10

3.3.3 EMC effects on cables ...........................................................................................11

3.3.4 EMC effects from magnetic fields...........................................................................11

4Technical Data 12

5Radio Approvals 14

5.1 Europe (CE) ..........................................................................................................14

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 4 of 15

M90402-1e-ID-B

1 Safety Instructions / Warning - Read before start-up !

The device may only be used for the purpose intended by the manufacturer.

The operation manual should be kept readily available at all times for each user.

Unauthorized changes and the use of spare parts and additional devices which have not been

sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such

unauthorized measures shall exclude the manufacturer from any liability.

The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid

for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,

or omissions in the manual or automatically set parameters for a device or for an incorrect

application of a device.

Repairs may only be undertaken by the manufacturer.

Installation, operation, and maintenance procedures should only be carried out by qualified

personnel.

Use of the device and its installation must be in accordance with national legal requirements

and local electrical codes .

When working on devices the valid safety regulations must be observed.

Before touching the device, the power supply must always be interrupted. Make sure that the

device is without voltage by measuring. The fading of an operation control (LED) is no indicator

for an interrupted power supply or the device being out of voltage!

Special advice for wearers of cardiac pacemakers:

Although this device doesn't exceed the valid limits for electromagnetic fields you should keep

a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in

the immediate proximity of the device’s antenna for any length of time.

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 5 of 15

M90402-1e-ID-B

2 Performance Characteristics of the ID ISC.M02.M8-B Reader Module

2.1 Performance Characteristics

The ID ISC.M02.M8-B reader module is designed for reading and writing passive transponders, so-

called “Smart Labels”, with an operating frequency of 13.56 MHz according to the ISO15693

standard. It is suitable for any application in which short read ranges and small reader dimensions

are required.

The module has an integrated antenna multiplexer. Up to 8 external antennas can be connected.

2.2 Available module

The following reader types are available:

Module type

Description

ID ISC.M02.M8-B

1 x Reader module ID ISC.M02.M8-B

Table 1: Available module version

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 6 of 15

M90402-1e-ID-B

3 Installation and wiring

3.1 Dimensions

Fig. 1 shows the dimensions of the ID ISC.M02.M8-B Reader Module in mm.

5±0,3 65±0,3

80±0,3

5±0,3

45±0,3

50±0,3

16,5±0,3

4±0,3

Ø4,2±0,1

2,5±0,6

14,1±0,3

87±0,3

2,54

Fig. 1: Dimension of the Readermodul ID ISC.M02.M8-B

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 7 of 15

M90402-1e-ID-B

3.2 Wiring

Figure 1 and Table 2 show the pin assignments for Terminal X9. The pin connector is designed for

flat cable connection using a 5 pin multipoint socket connector type MTA 100 company AMP.

Pin-No.

Function

Description

GND **

GND

TxD

RS232-LVTTL –Send data

Vin *

+ 24VDC

RxD

RS232-LVTTL –Receive data

GND **

GND

* Use only regulated DC power supplies !

Table 2: Pin Assignment of the multipoint connector X9

Note:

A wrong polarity of the DC voltage will destroy the reader

3.2.1 Supply voltage

The reader ID ISC.M02.M8-B has to supplied by a limited power supply (e.g. NEC Class 2/LPS

power supply) according IEC EN 60950, only.

If switching power supplies are used with the module, be sure that there is adequate filtering.

Noise from the power supply can result in a reduction of the read/write range of the module.

The cable length from the power supply should be as short as possible, and should in any case not

exceed 1 m.

Note:

A wrong polarity of the DC voltage will destroy the reader

Supply voltages outside the specifications may destroy the device.

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 8 of 15

M90402-1e-ID-B

3.2.2 RS232-LVTTL-Interface (3,3V)

The length of the cable to the RS232 LVTTL interface should be kept as short as possible, and

must in any case not exceed 1 m.

The transmission parameters for the interface can be software-configured.

Table 3 shows the standard parameters for the RS232 interface.

Parameter

Default Setting

Baudrate

38400 bit/s

Number of Data bits

Parity

Even

Number of Stop bits

Table 3 Default parameter of the RS232 LVTTL

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 9 of 15

M90402-1e-ID-B

3.2.3 Connection of the external antennas

Up to 8 external antennas can be connected.

For the connection of the external antennas 8 antenna connectors (X1..X8 respectively A1..A8) are

available.

The connector type is U.FL-R-SMT from the company Hirose. .

Alternatively a 16pin connector can be used for the connection of the antennas.

Figure 1 shows the pin assignment.

Figure 1: Antenna connector‘s

Note:

The maximum antenna cable length should not increase a maximum length of 50cm

(24inch)

The input impedance for the antenna must be calibrated to a value of









3°).

A not correct tuned antenna can destroy the reader.

The optimum working quality of the antenna should be in a range of QB = 10...20.

For measuring the working quality the antenna must be connected with a 50



-source,

e.g. a network analyzer or a frequency generator

When connecting an antenna, ensure that it does not exceed the permissible limits pre-

scribed by the national regulations for radio frequency devices.

The ultraminiatur coax connector can be used for up to about 20 connection cycles. For

the disconnection the „Extraction Tool“ must be use according to the recommendation

from the manufacturer.

OBID i-scan® HF

Installation

ID ISC.M02.M8-B

FEIG ELECTRONIC GmbH

Page 10 of 15

M90402-1e-ID-B

3.3 Installation notes

The reader module has been designed for the installation in a device.

3.3.1 Mounting

The reader module can be mounted by using 4mm (M4) screws.

Component side: the maximum head diameter should not increase more than 8mm.

Preferred no metallic screws should be used (DIN7985).

Alternatively internal hexagon screws can be used (DIN 912).

Component underside: conductive materials can have a diameter of 6mm.

Non-conductive materials can have a diameter of up to 10mm.

The mounting orientation of the reader module is arbitrary. The component side on the top is

the preferred orientation.

Check the planed mounting place first for suitability.

3.3.2 Influence

Be aware of the following possible environmental factors when installing the module into another

device :

Effects from nearby metal objects

Detuning of the integrated antenna

Impaired propagation of the antenna’s magnetic field

EMC effects on cables

Impaired communication between reader and transponder

EMC effects from magnetic fields

Impaired communication between reader and transponder

Andere Handbücher für OBID i-scan ID ISC.M02.M8-B

Inhaltsverzeichnis

Andere Feig Electronic Steuereinheit Handbücher

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270 Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.PR101-USB Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02 Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-B Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.PRH102-B Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02.M8-B Bedienungsanleitung

Feig Electronic

Feig Electronic OBID ID RWA02.ABCD Series Benutzerhandbuch

Feig Electronic

Feig Electronic ID ISC.LRM1002-E Gebrauchs- und Pflegehandbuch

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LR2500-A Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-B Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02 Bedienungsanleitung

Feig Electronic

Feig Electronic TST WUI Installationshandbuch

Feig Electronic

Feig Electronic cVEND plug Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.M02.M8 Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.MU02.02 Bedienungsanleitung

Feig Electronic

Feig Electronic ID MAX.U1002 Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MAT-A Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan D ISC.MU02.02 Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LR200 Series Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.MU02.02-CU Bedienungsanleitung

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung