Feig Electronic ID ISC.MR102 Bedienungsanleitung
INSTALLATION MANUAL
final –public (B)
2018-01-18 –M01210-6e-ID.doc
ID ISC.MR102
For all variants
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 2 of 26
M01210-6e-ID.doc
Note
Copyright 2011 –2018 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg-Waldhausen
Tel.: +49 6471 3109-0
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-
ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 3 of 26
M01210-6e-ID.doc
Content
ID ISC.MR102 1
For all variants 1
Safety Instructions / Warning - Read before start-up ! 5
Performance Features of the readers 6
Available Reader types ............................................................................................................6
Optional accessories ...............................................................................................................6
Assembly and Wiring 7
Housing versions.....................................................................................................................7
Dimensions............................................................................................................................7
Module version......................................................................................................................... 8
Dimensions............................................................................................................................8
Connections 9
Antenna terminal ANT 1......................................................................................................... 10
DC Voltage supply on antenna connector ANT1..................................................................10
Power supply..........................................................................................................................11
Power supply via X1 ............................................................................................................ 11
Power supply via PoE (Power over Ethernet) on X4 (ID ISC.MR102-PoE) ..........................12
Power supply and interface connection on X2 (ID ISC.MR102-A).......................................13
RS232 Interface (ID ISC.MR102-A) ..................................................................................... 13
Ethernet-Interface on X2 (10/100Tbase)................................................................................ 14
USB –Interface X3 (Host communication) ...........................................................................14
Control and display elements LED 15
LED.......................................................................................................................................... 15
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 4 of 26
M01210-6e-ID.doc
Technical Data 16
Radio Approvals 18
Europe (CE) ............................................................................................................................ 18
Europe (CE) ............................................................................................................................ 19
USA (FCC) and Canada (IC)................................................................................................... 20
UL Approval - USA and Canada 22
Annex 23
Accessories............................................................................................................................23
Wall mounting kit ID ISC.MS.MR/PR-A................................................................................24
Serial data cable ID CAB.RS-A............................................................................................25
Antenna...............................................................................................................................26
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 5 of 26
M01210-6e-ID.doc
Safety Instructions / Warning - Read before start-up !
The device may only be used for the purpose intended by the manufacturer.
The operation manual should be kept readily available at all times for each user.
Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude the manufacturer from any liability.
The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
Repairs may only be undertaken by the manufacturer.
Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
When working on devices the valid safety regulations must be observed.
Before touching the device, the power supply must always be interrupted. Make sure that the
device is without voltage by measuring. The fading of an operation control (LED) is no indicator
for an interrupted power supply or the device being out of voltage!
Special advice for wearers of cardiac pacemakers:
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep
a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in
the immediate proximity of the device’s antenna for any length of time.
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 6 of 26
M01210-6e-ID.doc
Performance Features of the readers
The Reader ID ISC.MR102 is designed for reading passive data carriers, so-called „Smart Labels“
at an operating frequency of 13.56 MHz.
The ID ISC.MR102 is suitable for all applications in which moderate reading distances are re-
quired. Also required is an external antenna connected to the Reader.
An anticollision function enables simultaneous reading of up to 100 * ISO15693 or ISO18000-3M3
transponders per second.
The Reader electronics is contained in a plastic housing having an IP30 enclosure rating.
Available Reader types
The following reader types are currently available:
Reader type
Description
ID ISC.MR102-A
Housing version with asynchronous RS232 interface
ID ISC.MRM102-A
Module version with asynchronous RS232 interface
ID ISC.MR102-PoE
Housing version with LAN interface and Power over Ethernet
ID ISC.MR102-USB
Housing version with USB-Schnittstelle
ID ISC.MRM102-USB
Module version with USB-Schnittstelle
Table 1: Reader types
Optional accessories
Optional Accessories are listed in the attachment.
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 7 of 26
M01210-6e-ID.doc
Assembly and Wiring
Housing versions
The Reader is designed for an office environment. It can be wall-mounted, in this case the wall-
mount kit should be ordered separately.
(see Appendix: Wall mounting kit ID ISC.MS.MR/PR-A)
Notes:
The distance between two readers of the same type should not fall below 4m.
Before any installation the intended position of the reader should be tested for it´s suit-
ability.
Dimensions
Figure 1: Dimensions oft he housing version (all dimensions are in mm)
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 8 of 26
M01210-6e-ID.doc
Module version
This reader version has been designed for mounting in other equipment.
Notes:
The distance between two readers of the same type should not fall below 4m.
Before any installation the intended position of the reader should be tested for it´s suit-
ability.
Dimensions
77
137
Ø3,3
Ø7
125
107,5
65
LED
ANT1
FE 698
68,5
54,5
29,5
X2
X1
X3 X4
Figure 2: Dimensions of the module version (all dimensions in mm)
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 9 of 26
M01210-6e-ID.doc
Connections
Depending on the reader variant different connectors are available. Figure 3: Connection overview
displays the arrangement and the Table 2: Connectors shows which connector can be used for the
different interface cable.
X2
X4 X1
X1X3
ID ISC.MR102-PoE
ID ISC.MR102-USB
ANT 1
ID ISC.MR102
ID ISC.MR102-A
Figure 3: Connection overview
Connector
Description
ANT 1
Antenna terminal ANT 1 (Impedance 50Ohm)
X1
Power supply 12 - 24VDC
X2
RS232 Interface
X3
USB Interface
X4
10/100Tbase Ethernet interface with RJ-45 (PoE)
Table 2: Connectors
Identification
Installation
ID ISC.MR102
FEIG ELECTRONIC GmbH
Page 10 of 26
M01210-6e-ID.doc
Antenna terminal ANT 1
A SMA socket is provided on the circuit board for connecting the external antenna.
The maximum tightening torque for the SMA socket is 0.45 Nm.
Caution:
Higher tightening torque will damage the connector.
Terminal
Description
X4
Connecting the external antenna
(input impedance 50)
Table 3: Connecting the external antenna
Note:
The input impedance for the antenna must be calibrated to a value of
50
(15
15°).
If the antenna ID ISC.ANT340240 is used a minimum distance of 20cm to any metal parts
are necessary. Otherwise there is a danger that the reader will be destroyed.
The optimum operating Q factor of the antenna should be in a range of QB = 10...20. To
determine the operating Q the antenna must be supplied with a 50 Ohm source such as
a network analyzer or frequency generator.
When connecting an antenna, ensure that it does not exceed the permissible limits pre-
scribed by the national regulations for radio frequency devices.
DC Voltage supply on antenna connector ANT1
The reader is able to provide a DC voltage on the antenna output ANT1. With this DC voltage a
external LED can be supported for example.
Note:
This DC voltage (7,5V± 1V) is designed for low current (max. 5mA) only.
Only antennas can be used which are designed for DC voltage and do not short cut DC
voltages.
For the connection of other devices (e.g. VSWR-Meter) it is necessary to check if DC
voltage is allowed.
This DC voltage is not sufficient for powering the ID ISC.DAT tuning board.
Andere Handbücher für ID ISC.MR102
1
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Feig Electronic IP-Zugriffskontrollsysteme Handbücher
