Felix Storch Pro L Series Bedienungsanleitung
How to replace the ribbon cable
16 March
2022
Revision 0
FELIX Pro L and XL
series
How to replace the ribbon cable
16 March 2022
1
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
1Introduction
This manual explains how to replace the ribbon cable properly.
2Tools
The tools you need to replace the ribbon cable of the Pro L and XL:
•Allen key 2,5
•Allen key 5
•Tweezers
3Preparations
Warning: Always turn off the printer and remove the power cable
before working on the printer.
1) Turn of the printer
-Turn off the printer and remove the power cable
from the printer.
How to replace the ribbon cable
16 March 2022
2
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
2) Remove the back cover
-Remove the tubes. Green squares .
-Loosen the M4 bolts for around 4 rotations
using an allen key 2,5. Red circles
-Remove the back cover by removing the M8
bolts with a allen key 5. Blue triangles.
3) Remove cover
-Remove the cable tray cover by gently pressing
the pins.
How to replace the ribbon cable
16 March 2022
4
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
2) Disconnect sensor cable
-Remove the sensor cable. Red circle.
3) Disconnect the ribbon cables
-Disconnect the ribbon cables.
Be careful to not destroy the
connectors. Red circle.
You can use tweezers.
How to replace the ribbon cable
16 March 2022
5
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
4) Disconnect the ribbon cables at the printhead
-Disconnect the ribbon cables.
Be careful to not destroy the connectors.
Red circles.You can use tweezers.
5) Disconnect the servo cable at the printhead
-Disconnect the servo cable. Red circle.
How to replace the ribbon cable
16 March 2022
7
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
3) Remove the spring bolts
Warning: Don’t lose the plate that is positioned behind the spring!
-Loosen the bolts with an allen key 2,5.
Red circles.
4) Remove the ribbon cable
-Gently remove the ribbon cable out of the printer.
How to replace the ribbon cable
16 March 2022
8
FELIX Pro L XL
www.FELIXprinters.com
Pro L XL series
6Place the new ribbon cable
1) Place the new ribbon cable
-Grap the new ribbon cable assembly and place the backend trough the back plate.
2) Fix the ribbon cable spring
-Fix the spring with de 2 bolts. Use an allen key 2,5. Make sure you place the plate between
the spring and the backplate. Red circles.
Andere Handbücher für Pro L Series
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Felix Storch 3D-Drucker Handbücher
Felix Storch
Felix Storch Pro 3 L Bedienungsanleitung
Felix Storch
Felix Storch Food 1.5 Bedienungsanleitung
Felix Storch
Felix Storch Pro Series Bedienungsanleitung
Felix Storch
Felix Storch FELIXFOOD 3D Bedienungsanleitung
Felix Storch
Felix Storch 2.0 Bedienungsanleitung
Felix Storch
Felix Storch Pro L Series Bedienungsanleitung
Felix Storch
Felix Storch Tec 4.0 to Tec 4.1 Upgrade Kit Kurzanleitung
Felix Storch
Felix Storch Pro 3 Bedienungsanleitung
Felix Storch
Felix Storch 3.1 Single Bedienungsanleitung
Felix Storch
Felix Storch Pro L Series Bedienungsanleitung
