Fellowes Esi Kata Series Bedienungsanleitung

installation instructions

Kata™slider mount

model KATA-SLD-SLV

model KATA-SLD-BLK

model KATA-SLD-WHT

VESA slider retrot

Page 2

Please review these instructions before beginning the installation. Use the illustrations below to check

that all the components needed for your installation were provided with your order. Do not discard the

packaging until the product works to your satisfaction.

components and tools

additional tools required

• Phillips screwdriver

caution

• Hand tighten screws only. Do not use power tools.

Kata™slider mount components and tools

slider bar (1)

VESA mount assembly (1)

dual Allen key (1)

2mm and 4mm

M4x15

M4x10

VESA plate screws (4) VESA locking screw (1)

M4x9

slider mount set screw (1)

Page 3

step 1: remove monitor from VESA mount

• Disconnect the monitor cables.

• If a VESA locking screw is installed, remove

it using the 2mm Allen key, as shown below.

• Push forward the tab at the top of the VESA

plate and lift the monitor upward.

• Place the monitor face down on a ﬂat surface.

step 2: remove VESA mount from monitor arm

• Remove the socket cap screw cover from the underside of the monitor arm.

• Remove the socket cap screw using the 4mm Allen key.

• Pull the VESA mount from the monitor arm.

— There are two bushings on which the VESA mount swivels, as shown in the right illustration. Remove

the bushings and save them for re-use. [Or: You may re-use the bushings or use the new ones

provided.]

Kata™ slider mount retrot procedure

VESA

mount

VESA

plate

push tab forward

screw cover

lower bushing

upper bushing

socket cap

screw

4mm Allen key

screw cover

lower bushing

upper bushing

socket cap

screw

4mm Allen key

remove

VESA locking screw

M4x15

2mm Allen key

Page 4

Kata™ slider mount retrot procedure

step 3: assemble slider mount

IMPORTANT: When assembling the slider mount, the groove on the slider bar must be at the bottom.

• Slide the VESA mount assembly onto the slider bar. Center the assembly on the slider bar.

• Install the M4x15 locking screw into the bottom of the VESA mount assembly. Using the 2mm Allen key,

tighten the locking screw to hold the assembly in place. Be sure the screw ﬁts into the groove.

— After the monitor has been installed, the VESA mount can be moved anywhere along the slider bar

by loosening the locking screw no more than one full turn, so that it stays inside the groove. Be sure

to re-tighten the screw to secure the monitor in the desired position.

step 4: position slider mount on monitor arm

• First, position the bushings.

— Place the upper bushing on the top opening of the slider mount.

— Place the lower bushing onto the bottom opening of the monitor arm.

• Position the slider mount onto the monitor arm. Be sure the

bushings remain in place.

screw cover

lower bushing

upper

bushing

socket cap

screw 4mm

Allen key

slider bar

VESA mount

assembly

2mm

Allen key

slider mount set screw

M4x9

groove

Page 5

Kata™ slider mount retrot procedure

step 5: attach slider mount

• Secure the slider mount using the socket screw.

— Do not over-tighten. The slider mount should hold its position, but still

swivel when force is applied.

• Install the socket screw cover.

screw cover

lower bushing

upper

bushing

socket cap

screw 4mm

Allen key

VESA

mount

slider

VESA

plate

push tab forward

step 6: remove VESA plate from VESA mount

• Remove the VESA plate from the VESA mount by pushing

forward the tab at the top and lifting upward.

Page 6

Kata™ slider mount retrot procedure

VESA plate screw

VESA

plate monitor

(face down)

top

3.9"

(100mm)

(75mm)

step 7: only if not reattaching original monitor: attach VESA plate to new monitor

Skip this step if you are using the original monitor.

• Place the monitor face down on a ﬂat surface. Align the VESA plate holes with the holes on the back of

the monitor. Attach the VESA plate using the four VESA plate screws provided.

— There are two sets of four holes on the VESA plate. One set has holes 3.9” (100mm) apart, the other

set has holes 3” (75mm) apart. Use the set that matches the holes on the rear of the monitor.

step 8: attach monitor to VESA mount

• Slide the VESA plate and monitor onto the

VESA mount.

— Make sure the VESA plate clicks securely

in place.

• OPTIONAL: Secure the VESA plate to

the VESA mount using the M4x15 VESA

locking screw, as shown below.

VESA

mount

VESA

plate

2mm Allen key

VESA locking screw

M4x15

Page 7

Kata™ slider mount retrot procedure

step 9: organize cables and cords

• Connect the monitor cables and cords.

• Capture the cables and cords with the cable covers. Slide the

cable covers downward to attach them to the monitor arms.

• Route the monitor cables and power cords toward the rear

by slipping the cords into the opening on the cable clips.

install

over

cables

capture

cables

in clip

slide

down to

install

step 10: adjust monitor position, if desired

• Loosen the slider mount set screw with the 2mm Allen key. Slide the monitor

to the desired position on the slider bar and then re-tighten the set screw.

• All tension adjustments are the same as before the slider mount retroﬁt:

1. Monitor swivel adjustment (4mm Allen key)

2. Motion arm weight adjustment (4mm Allen key)

3. Monitor tilt adjustment (4mm Allen key)

4. Motion arm swivel adjustment (4mm Allen key)

5. Fixed arm swivel adjustment (2mm Allen key)

monitors

not shown

behind

slider

2mm

Allen

key

LIMITED WARRANTY

ESI warrants this product to be free from defects in manufacturing for a period of 15 years from the date of original purchase.

This warranty extends only to the original purchaser, and does not apply if the product has been damaged or fails to function

properly as a result of misuse, abuse, modiﬁcation, alteration, or improper cleaning or maintenance. This warranty does not

apply to damage in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use

(meaning consistent use in excess of an eight hour shift). ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE.

ESI’s sole obligation under this warranty or any implied warranty, and the purchaser’s sole remedy, is limited to the repair

or replacement, at ESI’s option, of the product or any defective part. Costs (such as installation, labor fees or express

shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS

AFFILIATES, SUBSIDIARIES, RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES, BE LIABLE

FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES.

To make a warranty claim, contact ESI at 800-833-3746 or customerservice@esiergo.com. You must provide proof of

purchase, such as the original purchase order number.

The duration, terms and conditions of this warranty are valid worldwide, except where dierent limitations, restrictions or

conditions may be required by local law.

Kata slider mount

VESA slider retrot

Please contact Customer Service with any

questions or comments at 800.833.3746

or visit our website at esiergo.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fellowes Rack & Stand Handbücher

Fellowes

Fellowes Cambio 48 Bedienungsanleitung

Fellowes

Fellowes esi Kata EX Series Bedienungsanleitung

Fellowes

Fellowes RisingEX 1F Bedienungsanleitung

Fellowes

Fellowes AERAMAX PRO AM3 Bedienungsanleitung

Fellowes

Fellowes Lotus VE Sit-Stand Bedienungsanleitung

Fellowes

Fellowes ESI Kata EX3-FMS Series Bedienungsanleitung

Fellowes

Fellowes KATAEX1-DC-FM Series Bedienungsanleitung

Fellowes

Fellowes Esi Kata EX2-FF Series Bedienungsanleitung

Fellowes

Fellowes ESI Evolve Stücklistenhandbuch

Fellowes

Fellowes Tallo Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

Fellowes esi Kata Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken