Festo CMCA series Bedienungsanleitung
Description
Electrical installation
8023865
1211a
Control system
CMCA
CMCA
2 Festo – GDCP-CMCA-INST-EN – 1211a –
Translation of the original instructions
GDCP-CMCA-INST-EN
CoDeSys
®
is a registered trademark of its respective trademark holder in certain countries.
Identification of hazards and instructions on how to prevent them:
Warning
Hazards that can cause death or serious injuries.
Caution
Hazards that can cause minor injuries or serious material damage.
Other symbols:
Note
Material damage or loss of function.
Recommendations, tips, references to other documentation.
Essential or useful accessories.
Information on environmentally sound usage.
Text designations:
• Activities that may be carried out in any order.
1. Activities that should be carried out in the order stated.
– General lists.
CMCA
Festo – GDCP-CMCA-INST-EN – 1211a – English 3
Table of Contents – CMCA
1 Safety and requirements for product use 5......................................
1.1 Safety 5..................................................................
1.1.1 General safety instructions 5.........................................
1.1.2 Intended use 5.....................................................
1.1.3 Foreseeable misuse 6...............................................
1.2 Requirements for product use 6...............................................
1.2.1 Technical requirements 6............................................
1.2.2 Qualification of trained personnel 6....................................
1.2.3 Range of application and certifications 6................................
2 Transport and storage 7.....................................................
2.1 Transport 7................................................................
2.1.1 Dimensions and weights 7...........................................
2.2 Storage conditions 8........................................................
2.3 Unpacking 8...............................................................
2.3.1 Mounting plate design CMCA-…-C-… 9..................................
2.3.2 Control cabinet versions CMCA-…-CC-…/CMCA-…-CS-… 10...................
2.4 Checking control system and scope of delivery 13..................................
3Overview 14................................................................
3.1 Characteristics 14...........................................................
3.2 Function and application 15....................................................
3.3 Product overview 16.........................................................
3.3.1 Control sections and connections, control cabinet CMCA-…-CC-…/CMCA-…-CS-… 16
3.3.2 Control and signal elements on the control cabinet
CMCA-…-CC-…/CMCA-…-CS-… 17.......................................
3.3.3 Components and connections inside the control cabinet or mounting plate
design 18..........................................................
3.3.4 Overview, terminal strips 19...........................................
3.3.5 Overview, fuses 20..................................................
4 Mounting and installation 21..................................................
4.1 Mounting 21................................................................
4.1.1 Mounting plate design CMCA-…-C-… 21..................................
4.1.2 Control cabinet version CMCA-…-CC-… 22.................................
4.1.3 Control cabinet version with base CMCA-…-CS-… 23........................
CMCA
4 Festo – GDCP-CMCA-INST-EN – 1211a – English
4.2 Electrical installation 24.......................................................
4.2.1 Safety instructions 24................................................
4.2.2 Design of the double-stack terminals 26.................................
4.2.3 Connecting supply voltage 26..........................................
4.2.4 Connect power switch (with mounting plate design) 27.....................
4.2.5 Connect emergency stop switch (with mounting plate design) 28..............
4.2.6 Connect emergency stop circuits 29.....................................
4.2.7 Connect protective door switch 29......................................
4.2.8 Connect operating and signal elements (with mounting plate design) 30........
4.2.9 Operating mode selection 31..........................................
4.2.10 Connect kinematic drives 32...........................................
4.2.11 Connect limit switches 32.............................................
4.2.12 Rod loss detection (only for rod kinematic system EXPT) 33..................
4.2.13 Connect axis of rotation reference sensor 33..............................
4.2.14 Connect the camera system supply 33...................................
4.2.15 Connect lighting 33..................................................
4.2.16 Freely usable outputs 34..............................................
4.2.17 Additional peripheral modules for the multi-axis controller 34................
5 Commissioning 35...........................................................
6 Operation and diagnostics 36..................................................
6.1 Operation 36...............................................................
6.2 Maintenance and care 36......................................................
6.2.1 Control cabinet fan 36................................................
7 Module replacement and repair 37.............................................
7.1 Replace module 37..........................................................
7.2 Repair 37..................................................................
7.3 Disposal 37................................................................
A Technical appendix 38........................................................
A.1 Technical data 38............................................................
A.1.1 Safety engineering 38................................................
A.1.2 General 38.........................................................
A.1.3 Electrical data 39....................................................
A.1.4 Operating and environmental conditions 39...............................
1 Safety and requirements for product use
Festo – GDCP-CMCA-INST-EN – 1211a – English 5
1 Safety and requirements for product use
1.1 Safety
1.1.1 General safety instructions
• Observe the general safety instructions in the corresponding chapters.
Specific safety regulations can be found immediately before the task instructions.
Warning
Danger of electric shock even if power switch is shut off.
The control system is only completely voltage-free if all supply lines have been switched
voltage-free.
• Switch off all supply lines (also external voltage) prior to assembly, installation
and/or maintenance work and secure them from being restarted accidentally.
• Switch the voltage back on only after completion of work.
Note
Damage to the product from incorrect handling.
• Never pull the plugs and interfaces when powered.
• Never plug in plugs and interfaces when powered.
• Observe the handling specifications for electrostatically sensitive devices.
1.1.2 Intended use
The control system CMCA serves to operate a kinematics system in the environment of a machine or
automated systems and must be used as follows:
– in excellent technical condition
– in original status, without unauthorised modifications
– within the limits of the product defined by the technical data (appendix A.1)
– in an industrial environment
The safety circuit of the CMCA control solution is only one part of the the safety concept for a machine,
whereby the safety concept must be based on a risk assessment of the entire machine to be performed
by the machine manufacturer.
Note
In the event of damage caused by unauthorised manipulation or other than intended
use, the guarantee is invalidated and the manufacturer is not liable for damages.
1 Safety and requirements for product use
6 Festo – GDCP-CMCA-INST-EN – 1211a – English
1.1.3 Foreseeable misuse
– The safety circuit of the CMCA control solution is changed in its function.
– Safety functions are thus implemented that are not specified in this description.
– An adequate risk assessment is not performed for the machine.
– There is no safety concept of the machine available.
– Suitability of this safety circuit for the application is not established.
– No verification and no validation of the switch is performed in the machine.
1.2 Requirements for product use
• Make this documentation available to the design engineer, installer and personnel responsible for
commissioning the machine or system in which this product is used.
• Make sure that the specifications of the documentation are always complied with. Also consider the
documentation for the other components and modules.
• Take into consideration the legal regulations applicable for the destination, as well as:
– regulations and standards
– regulations of the testing organizations and insurers
– national specifications
1.2.1 Technical requirements
General conditions for the correct and safe use of the product, which must be observed at all times:
• Comply with the connection and environmental conditions of the product (appendix A.1) and all
connected components specified in the technical data.
Only compliance with the limit values or load limits permits operation of the product in accordance
with the relevant safety regulations.
• Observe the instructions and warnings in this documentation.
1.2.2 Qualification of trained personnel
The product should only be installed by properly trained personnel in accordance with these instruc-
tions. The trained personnel must be familiar with:
– installation and operation of electrical control systems
– the applicable regulations for operating safety-engineered systems
– the applicable regulations for accident protection and industrial safety
– the documentation for the product
1.2.3 Range of application and certifications
Standards and test values which the product complies with and fulfils can be found in the technical
data (appendix A.1). The product-relevant EU directives can be found in the declaration of conform-
ity.
Certificates and the declaration of conformity for this product can be found at
www.festo.com.
2Transportandstorage
Festo – GDCP-CMCA-INST-EN – 1211a – English 7
2 Transport and storage
2.1 Transport
The control system is delivered on a pallet and is protected with a cover of plates. The mounting plate
design CMCA-…-C-… is also screwed to the pallet.
2.1.1 Dimensions and weights
CMCA-…- C-… CC-… CS-…
Dimensions [mm]
H565 868 1018
L1010 1140 1140
B640 510 510
Weight [kg]
Control system 41 79 89
Overall weight
1)
85 125 142
1) With max. accessories
Tab. 2.1
Note
• For transport, observe the marking on the upper side of the transport box.
1. Transport the pallet with the control system to the installation/storage location.
2. Set down the pallet on a firm and flat base at the installation/storage location.
2 Transport and storage
8 Festo – GDCP-CMCA-INST-EN – 1211a – English
2.2 Storage conditions
For safe later use, the following storage conditions must be complied with.
Storage conditions
Storage temperature [°C] –20 … +60
Relative air humidity [%] 10 … 95, non-condensing or protected against condensation
Max. storage time 60 months
Requirements of storage location dry, solid and flat base
Tab. 2.2
2.3 Unpacking
Note
Damage to the product from incorrect removal of the transport box.
• Use the correct tool to loosen the screws.
• Make sure that no packaging parts can fall onto the control system.
• Observe the product weight (chapter 2.1.1).
• Keep the packaging for later use or dispose of it in accordance with the instructions
(chapter 7.3).
2Transportandstorage
Festo – GDCP-CMCA-INST-EN – 1211a – English 9
2.3.1 Mounting plate design CMCA-…-C-…
Removing transport packaging
1. Loosen and remove the lower screws of the
cover.
2. Lift the cover up and off.
Remove the packaging foil
3. Cut the foil parallel to the contour of the
product with an appropriate tool. When cut-
ting, make sure that you do not damage or
scratch the components of the control system.
4. Pull the foil up and off. Carefully remove the
bag with desiccant and dispose of it in accord-
ance with the instructions (chapter 7.3).
Loosen mounting plate
5. Loosen and remove the screws with which the
mounting plate is screwed to the pallet.
6. With two people, lift the control system off the
pallet and bring it to the installation site.
Fig. 2.1
2 Transport and storage
10 Festo – GDCP-CMCA-INST-EN – 1211a – English
2.3.2 Control cabinet versions CMCA-…-CC-…/CMCA-…-CS-…
Warning
Danger of injury/damage due to falling loads.
The device to lift the control cabinet out of the transport packaging must be sufficiently
dimensioned for the weight of the control cabinet.
• Observe the product weight (chapter 2.1.1).
Removing transport packaging
1. Loosen and remove all screws of the cover.
2. Remove the cover up and off the transport
box.
Fig. 2.2
3. Loosen and remove all screws of the side wall
near the control cabinet doors.
4. Pull the side wall forward and off.
Fig. 2.3
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Festo Steuerungssystem Handbücher
Festo
Festo LOGO! 8 TP EduTrainer Bedienungsanleitung
Festo
Festo CPX-E Stücklistenhandbuch
Festo
Festo Controller CECC-LK Stücklistenhandbuch
Festo
Festo Checkbox Compact CHB-C-X Bedienungsanleitung
Festo
Festo CDPX-X-E1-W Series Bedienungsanleitung
Festo
Festo EduTrainer 8071407 Bedienungsanleitung
Festo
Festo CPX-AP Series Bedienungsanleitung
Festo
Festo CMCA-...-B Series Bedienungsanleitung
Festo
Festo CMXR-C1 Bedienungs- und Montageanleitung
Festo
Festo ZSB-1/8-B Bedienungsanleitung
