Festo CECC-X-M1 series Stücklistenhandbuch

Brief description

Controller

CECCXM1

CECCXM1MV

CECCXM1MVS1

8079349

2017-09a

[8074647]

Controller CECC-X-M1

Festo CECC-X-M1-... 2017-09a2

PI PROFIBUS PROFINET®, CANopen®, CODESYS®, EtherCAT®,

EtherNet/IP®, IO-Link®, and MODBUS®are registered trademarks of

their respective trademark holders in certain countries.

This product uses opensource software which is subject to the

“GNU General Public License, Version 2”. The licensing conditions

of the GPL are located either in the product’s engineering tool or at

the following address: http://www.gnu.org/copyleft/gpl.html

Edition: 2017-09a

Original instructions

Ruiter Straße 82

73734 Esslingen

Germany

Internet: http://www.festo.com

E-Mail: service_international@festo.com

Festo CECC-X-M1-... 2017-09a English 3

English

1 Safety

1.1 General safety information

 Observe the safety instructions in the corresponding chapters.

Special safety regulations are placed immediately before the

task instruction.

Warning

Electric voltage

Risk of injuries caused by electric shock, damage to the machine and

system.

Danger of electric shock from voltage sources.

Before carrying out mounting, installation and/or maintenance work:

 Switch off the supply voltage and safeguard it against being

switched on again unintentionally.

 Use only power sources which guarantee reliable electrical isolation

of the operating voltage in accordance with

IEC60204-1/EN60204-1.

 Switch the voltages back on only after completion of work.

Note

Unauthorised access to the product can cause damage or malfunc

tions.

When connecting the product to a network:

 Protect the network from unauthorised access.

Measures to protect the network include: firewall, Intrusion Prevention

System (IPS), network segmentation, virtual LAN (VLAN), virtual

private network (VPN), security at physical access level (port security).

Further information èDirectives and standards on information tech

nology security, e.g. IEC 62443, ISO/IEC 27001. An access password

protects only against accidental changes.

Festo CECC-X-M1-... 2017-09a English

1.2 Intended use

The control documented in this brief description is exclusively intended

for installation in a machine or automated system.

The product may only be used as follows:

– as intended in an industrial environment

– for installation in a control cabinet

 The product may only be used in its original status without unauthor

ised modifications.

 Observe the permissible limit values and specifications

è13Technical data.

 Only use the product if it is in an excellent technical status.

Note

In the event of damage caused by unauthorised manipula

tion or other than intended use, the guarantee is invalidated

and the manufacturer is not liable for damages.

Festo CECC-X-M1-... 2017-09a English 5

2 Requirements for product use

 Make this brief description available to the design engineer, installer

and personnel responsible for commissioning of the machine or sys

tem in which these products are used.

 Make sure that the specifications of the documentation are always

complied with. Also consider the documentation for the other com

ponents and modules è13Technical data.

 Take into consideration the legal regulations applicable at the installa

tion site, as well as:

– regulations and standards

– regulations of the testing organisations and insurers

– national specifications

2.1 Training of skilled personnel

The following steps must only be carried out by qualified specialists:

– mounting

– installation

– commissioning

– maintenance

– repair

The trained personnel must be familiar with:

– electrical control technology

– the applicable regulations for operating safety-engineered systems

– the applicable regulations for accident prevention and occupational

safety

Festo CECC-X-M1-... 2017-09a English

3 Scope of delivery

– Controller CECC-X-M1-...

– This brief description

Software for the product can be found in the Festo Support

Portal èwww.festo.com/sp.

4 Accessories

– Camera

– Plug assortment

Catalogue èwww.festo.com/sp

Please consult your regional Festo contact if you have any technical

queries or questions regarding the accessories.

Festo CECC-X-M1-... 2017-09a English 7

5 Overview

5678aJ aA

aH aG

1Ethernet interfaces

2USB interfaces

3Functional earth connection

4Load voltage supply infeed

for IO-Link and power supply

for encoder

5Multi-functional interface

6Direct connections for motor

controller

7Torque-off input

8Load voltage supply for motor

controller

9Status LEDs

aJ Communication interfaces:

ENC, RS232, RS422, RS485

and IO-Link

aA CANopen interface CAN1

aB MicroSD card slot

aC CANopen interface CAN2

aD Digital inputs

aE Digital outputs

aF Analogue inputs

aG I/O interfaces

aH Infeed for I/O power supply

Fig. 1 Controller CECC-X-M1-...

Festo CECC-X-M1-... 2017-09a English

6 Installation

Note

Damage to the product from incorrect handling.

 Never pull out or plug in the plug connectors and inter

faces when powered.

 Observe the handling specifications for electrostatically

sensitive devices.

The product can be mounted on a H-rail or on a flat surface in any

mounting position.

 Ensure sufficient free space:

– above and below the product for connecting cables

– to the right of the product for cold-air entry and access to the Mi

croSD card slot.

122.2 mm

20 mm

aI Clip

bA Distance

bJ Mounting holes

Fig. 2

Festo CECC-X-M1-... 2017-09a English 9

6.1 Mounting on H-rail

1. Insert the product into the H-rail.

2. Press the product in the direction of the arrow until it audibly engages.

6.2 Dismounting from H-rail

1. Remove the plug connector on the underside of the product.

2. Unlock the product via the clip èFig. 2aI.

Use a suitable tool, e.g. a screwdriver.

3. Remove the product from the H-rail.

6.3 Mounting onto mounting surface

Note

Damage to the product caused by mounting on uneven or flexible

surfaces.

 Only mount the product on an even, torsionally rigid surface.

1. Drill two mounting holes bJ in the mounting surface (4.5 mm,

spacing èFig. 2 – hole pattern).

2. Secure the product in place with two M4 screws.

– Screw head diameter: 7 mm

– Max. tightening torque: 0.8 Nm

6.4 Dismounting from mounting surface

1. Loosen two M4 screws.

2. Remove the product from the mounting surface.

Additional information regarding installation and commissioning

can be found in the Festo Support Portal èwww.festo.com/sp.

Festo CECC-X-M1-... 2017-09a English

7 Status LEDs

The product is equipped with the following status LEDs èFig. 1 9:

Status LED Meaning Status LED Meaning

Run Application status Net Device detected

Error Error Mod Reserved

Fig. 3

8 Power supplies

Note

 Use an external overload protection for the power supply

of the device.

 Pay attention to the required current consumption.

8.1 Power supply [X1]

for device, digital/analogue inputs

and motor controller direct connection (logic)

Residual current for all supplied ports: 750 mA

of which intrinsic current consumption: 200 mA

Terminal Port Comments

X1.1 24 U+ power supply

X1.2 0 U– load

X1.3 Functional earth

X1.4 – Not connected

Fig. 4

Andere Handbücher für CECC-X-M1 series

Dieses Handbuch passt für folgende Modelle

Andere Festo Controller Handbücher

Festo

Festo CP-FB11-E Betriebsanleitung

Festo

Festo CMMO-ST-C5-1-LKP Bedienungsanleitung

Festo

Festo VZXA Series Bedienungsanleitung

Festo

Festo DFPD-HD-...-HW series Bedienungsanleitung

Festo

Festo SPC200 Series Bedienungsanleitung

Festo

Festo CMMP-AS-***-M0 Series Bedienungs- und Montageanleitung

Festo

Festo CMMS-AS Series Bedienungs- und Montageanleitung

Festo

Festo MPPES Series Bedienungsanleitung

Festo

Festo CMMP-AS-C2-3A Bedienungsanleitung

Festo

Festo VPPM-**C1 Series Bedienungsanleitung

Festo

Festo SPC200 Series Bedienungsanleitung

Festo

Festo VOFA-L26-T52-M Series Bedienungsanleitung

Festo

Festo CMMS-ST Series Leitfaden

Festo

Festo CECC-X-M1 series Bedienungs- und Montageanleitung

Festo

Festo CMMP-AS M3 Series Stücklistenhandbuch

Festo

Festo CDSB-A1 Bedienungsanleitung

Festo

Festo SEC-AC-305 Gebrauchsanweisung

Festo

Festo CMMP-AS-***-M3 Series Bedienungsanleitung

Festo

Festo ELCC-TB Bedienungsanleitung

Festo

Festo VPPM-6TA-L-1-F-0L10H Bedienungsanleitung

Festo

Festo CMMS-AS Referenzhandbuch

Festo

Festo SPC200 Series Bedienungsanleitung

Festo

Festo 32 MPA Bedienungsanleitung

Festo

Festo CMMS-ST-C8-7 Referenzhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch