Festo Bionic Fish Bedienungsanleitung

Bionic Fish

Assembly Instructions

FestoAG&Co.KGFesto DidacticSE

Equipment and Supplies

Required items from the Bionics Kit and/or Materials Pack:

1. Tail fin (large) assembled and attached to the plastic component (with cutouts) –see ‘Start Here’ for tail fin assembly instructions

2. Tail fin (small) assembled –2

3. Transparent corpus (body)

4. Small, waterproof servo motor (marked with a sticker)

5. Connecting element

6. Cable ties

7. Sealing rings –2

8. Tube (clear)

9. Electronic board with microcontroller

10. Material for fish tail and body (plastic poster board)

FestoAG&Co.KGFesto DidacticSE

Equipment and Supplies, continued

Additionally required:

1. Water basin

2. 4-AA batteries

3. Scissors

4. Items to balance the fish (nuts, bolts, coins, etc.)

5. Phillips head screwdriver

FestoAG&Co.KGFesto DidacticSE

If the tail fins have been previously assembled, please go directly to the Instructions on the next page.

Tail Fin Assembly

From the Bionics Kit, locate the bag containing the tools and 2 screws (used in Step 3). Next, locate the bags

containing the small screws and nuts (long and short) and the plastic support pieces (large and small).

To assemble the large tail fin, attach the large support pieces to the inside of the fin using the longer screws, nuts,

and tools.

Locate the plastic component (with cutouts). Place the opening on the base of the assembled large tail fin over the

post on the plastic component. Align the screw holes and connect the pieces together using the 2 screws and a

screwdriver.

Assemble the small fins using the small support pieces, the shorter

screws, nuts, and tools.

Start Here

FestoAG&Co.KGFesto DidacticSE

Instructions

Required items: 2 sealing rings, connecting element

Place the two sealing rings on each end of the connecting element.

Required items: assembled tail fin (large)

Attach the large tail fin to one side of the connecting element. Twist to lock it in place.

FestoAG&Co.KGFesto DidacticSE

Required items: clear tube

Attach the clear tube to the opening of the large tail fin. The top of the clear tube should

be at approximately the same level as the third support piece from the bottom of the fin.

If needed, cut the tube with scissors to the appropriate length.

Required items: small, waterproof servo motor

Attach the waterproof servo motor to the holder on the large tail fin, such that the rudder

horn of the motor points downwards. Guide the cable of the servo motor through the

clear tube.

FestoAG&Co.KGFesto DidacticSE

Required items: 1 cable tie

While holding the clear tube against the servo motor, connect it to the large tail fin with a

cable tie. Shorten the cable tie, if necessary.

FestoAG&Co.KGFesto DidacticSE

Required items: 4 cable ties

Connect the large tail fin to the rudder horns of the servo motor using 2 cable ties. Pull

the cable ties through the two small tabs of the fin and then through the openings of the

rudder horn in a crisscross fashion. The two cable ties cross above the fin. Add 2 more

cable ties to act as stopper.

Testing

Carefully move the rudder horn back and forth with your finger to check the tension of the

cable ties. If the fin does not move evenly, the length or the tension of the cable ties may

have to be corrected.

Shorten the cable ties, if

necessary.

FestoAG&Co.KGFesto DidacticSE

Required items: electronic board with microcontroller, 4 AA batteries

Insert the batteries, 2 on each side of the electronic board with microcontroller.

Required items: electronic board with microcontroller, small waterproof servo motor

Insert the plug of the servo motor into one of the electronics board’s set of pins.

FestoAG&Co.KGFesto DidacticSE

Required items: transparent corpus (body)

Insert the electronics board with microcontroller into the transparent corpus (body) and

slide it into the rail located inside. Turn the switch “on”. The small light on the electronics

board turns on.

Required items: tail fin (large)

Attach the connecting element onto the transparent corpus (body). Twist to lock it into

place.

Inhaltsverzeichnis

Andere Festo Robotik Handbücher

Festo

Festo MPS Station Bedienungsanleitung

Festo

Festo CP Factory Bedienungsanleitung

Festo

Festo CP Factory Bedienungsanleitung

Festo

Festo EHPS A-RA1 Series Bedienungsanleitung

Festo

Festo Robotino Bedienungsanleitung

Festo

Festo Chameleon Tongue Bedienungsanleitung

Festo

Festo Robotino 4.0 Bedienungsanleitung

Festo

Festo Bionic Elephant Trunk Bedienungsanleitung

Beliebte Robotik Handbücher anderer Marken

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Bedienungsanleitung

SunFounder

SunFounder PiDog Bedienungsanleitung

Universal Robots

Universal Robots UR5 Bedienungsanleitung

Universal Robots

Universal Robots E Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN-MPL80 II Bedienungsanleitung

EFORT

EFORT ECR5 Gebrauchsanweisung

Epson

Epson C8 Series Bedienungsanleitung

WowWee

WowWee ROBOQUAD Bedienungsanleitung

Milvus Robotics

Milvus Robotics SEIT 100 Bedienungsanleitung

RoboMaster

RoboMaster AI Robot 2020 Standard Version Bedienungsanleitung

fischertechnik

fischertechnik Mini Bots Bedienungsanleitung

YASKAWA

YASKAWA MA2010 Handbuch

Abicor Binzel

Abicor Binzel iCAT mini Bedienungsanleitung

ABB

ABB OmniCore E10 Bedienungsanleitung

YASKAWA

YASKAWA Motoman DX200 Bedienungsanleitung

pitsco

pitsco Tetrix Max Bedienungsanleitung

ECOVACS

ECOVACS DEEBOT R95 Bedienungsanleitung

Feng Yuan

Feng Yuan Interstellar Warrior Bedienungsanleitung