finder Bliss 2 Bedienungsanleitung
Step-by-step guide to accessing all the functions
of the Finder Bliss 2 smart chronothermostat
Type 1C.B1.9.005.0007
USER MANUAL
INDEX
OVERVIEW OF SCREENS & ICONS page 1
MANUAL MODE page 2
ON/OFF MODE page 3
AUTOMATIC MODE page 4
HUMIDITY page 5
GATEWAY ASSOCIATION page 6
TRANSMISSION TEST
WITH THE GATEWAY page 7
HEATING/COOLING page 8
OVERVIEW OF SCREENS & ICONS
ROOM TEMPERATURE
Thermostat is set to AUTOMATIC mode
(AUTO) and will respond to programming
via the App.
Current room temperature is displayed
HUMIDITY DETECTED IN THE ATMOSPHERE
In this section you can opt to view the level
of humidity in the atmosphere (% RH)
SETTINGS MENU
From here you can access the device settings
TARGETTEMPERATURE IN MANUAL MODE
The thermostat is set to MANUAL mode.
The target temperature is displayed
%RH
Display of Relative Humidity currently
present in the atmosphere
ASSOCIATION WITH THE GATEWAY
The opposing arrows will ash only during
the gateway pairing procedure
MANUAL MODE
Thermostat is set to Manual mode.
If the small arc segment at the top is coloured,
the heating or cooling system is active.
If red - heating If blue - cooling
ON/OFF SECTION
In this section you can turn
the thermostat ON or OFF
TRANSMISSION TEST WITH THE GATEWAY
At this point in the menu you can perform a signal
transmission test between the gateway and the
thermostat
HOURS SETTING
This displays the number of hours for
which the manual mode is to apply.
From 1 hour (h01) to permanent (h∞)
ON MODE
With ON mode selected, the thermostat
can function in either AUTO or Manual
modes
RESULT OF THE TRANSMISSION TEST WITH THE GATEWAY
0 SIGNAL ABSENT: the gateway is unreachable
1/6 POOR: bring the two devices closer
7/8 GOOD: make changes only if errors are found
9/10 VERY GOOD: stable connection
FULL ARC
Appears when a setting is accepted
and when the heating or cooling
system is active
OFF MODE
With the OFF mode selected, the thermostat
will still maintain a frost protection setting of
+ 5 ° C to avoid freeze damage to the system
FIRMWARE VERSION
At this point in the menu it is possible to view
the rmware version present on the device
BLISS2 user manual - 1
MANUAL MODE
With the display o, press the point
to turn the display on
To change the target temperature,
press + or – on the main screen
With the target temperature showing,
conrm by pressing the point
To set the number of hours for which the manual mode is to
apply (after which it will return to the AUTO (weekly) mode).
Press the + to increase the hours h01 = 1 hour, h02 = 2 hours, ...
Pressing the - until «h∞» is displayed will set the permanent
manual mode (until this is canceled via the App or thermostat.)
Conrm by pressing the center point
The arc will turn red if it is set on
heating or blue if it is on cooling
With the display o, press the
point to turn the display on
The small top segment of the arc will show
either red or blue, indicating respectively
that the heating or cooling system is active.
Press X to cancel Manual operation
and to return to AUTO operation
BLISS2 user manual - 2
ON/OFF MODE
With the display o, press the
point to turn the display on
Press the point to access
the internal menu
The“humidity”section will be displayed
as it is the rst item in the menu.
Press on the right arrow to move
on from the RH section
Press on the point to conrm if you
wish to enter the ON/OFF section
BLISS2 user manual - 3
This screen indicates with the“√”
that the thermostat is currently ON
Press the right arrow if you wish
to change this
Press on the point to conrm
you wish to select the OFF state
OFF mode is conrmed as being correctly set.
Exit the menu by pressing X, or wait for the
display to time out
With the display o, press the
point to turn the display on
Press X to exit the ON/OFF mode
AUTOMATIC (AUTO) MODE
With the display o, press the point
to turn on the display
If the thermostat is not on
AUTO, you will see the manual
“hand”or the OFF symbol
Press on the X to exit the current mode
to return to AUTO
Visual conrmation of AUTO mode setting
is shown on the display
At this point, room temperature is displayed
which signies operation in AUTO mode
BLISS2 user manual - 4
HUMIDITY
With the display o, press the point
to turn the display on
Press the point to access
the internal menu
The“humidity”section will be displayed
as it is the rst item in the menu.
Press on the point to enter this section
This screen shows the humidity (% RH).
Press on the X to go back
BLISS2 user manual - 5
BLISS2 user manual - 6
ASSOCIATION WITH THE GATEWAY
BEFORE FOLLOWING THE ASSOCIATION PROCEDURE, OPEN THE BLISS APP AND ADD A NEW DEVICE
Press the right arrow to keep
scrolling through the menu
Press on the point to access
the device settings
Press the point to put the thermostat
into pairing mode.
The opposing arrows will begin to ash
Visual conrmation of the correct association
is shown on the display
With the display o, press the point
to turn the display on
Press the point to access
the internal menu
The“humidity”section will be displayed
as it is the rst item in the menu.
Press on the right arrow to move on from
the RH section
TRANSMISSION TEST WITH THE GATEWAY
With the display o, press the point
to turn the display on
Press the point to access
the internal menu
The“humidity”section will be displayed
as it is the rst item in the menu
Press on the right arrow to move on from
the RH section
Scroll the menu to the device settings
icon and press the point
The“association”function will be shown
as it is the rst item.
Scroll on using the right arrow
Press the point to start
the signal test
RRESULT OF THE TRANSMISSION TEST WITH THE GATEWAY
0 SIGNAL ABSENT: the gateway is unreachable
1/6 POOR: bring the two devices closer
7/8 GOOD: make changes only if errors are found
9/10 VERY GOOD: stable connection
BLISS2 user manual - 7
HEATING/COOLING
ACCORDING TO THE OPERATING MODE OF THE CHRONOTHERMOSTAT, YOU WILL SEE DIFFERING VISUAL FEEDBACKS ON THE LUMINOUS ARC
HEATING
THE ARC IS RED
COOLING
THE ARC IS BLUE
BLISS2 user manual - 801/20 - Finder S.p.A. con unico socio - 10040 ALMESE (TO) - ITALY
Inhaltsverzeichnis
Andere finder Thermostat Handbücher
finder
finder BLISS2 Bedienungsanleitung
finder
finder 1C.81 Bedienungsanleitung
finder
finder 1T.31 Bedienungsanleitung
finder
finder 1T.41 Bedienungsanleitung
finder
finder BLISS T 1T.91 Bedienungsanleitung
finder
finder 1T Series Bedienungsanleitung
finder
finder 1C.71 Bedienungsanleitung
finder
finder BLISS WI-FI CHRONOTHERMOSTAT 1C.91 Bedienungsanleitung
finder
finder 1C Series Bedienungsanleitung
finder
finder 1C.51 Bedienungsanleitung
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
