Fireye FX Series Bedienungsanleitung
© 2022 Carrier 1
NEX-3001
January 18, 2022
Fireye FX Series
Modbus Controlled Actuator /Servo
Installation and Wiring
DESCRIPTION
This bulletin describes the installation and operating instructions for the FX series of servo motors.
These come in three sizes: FX04 (4Nm/3ft.-lb.), FX20 (20Nm/15ft.-lb.) and FX50 (50Nm/37ft.-lb.).
There are available in two baud rates: 56k for use with the NXF4000 or PPC4000 parallel positioning
system or 19.2k for general use with a PLC or other Modbus client. The FX04 size is also available in
a 38.4k baud rate for general use with a PLC or other Modbus client. Only the 56k model is approved
for use as part of a protective system (when used with the NXF4000 or PPC4000).
These servos are not compatible with or approved as replacements for the 945 series of
servos.
SAFETY INFORMATION
WARNING: When this equipment is mounted onto an appliance, all external
timers/controllers must be listed or recognized components and approved by
national certification agencies for the purpose for which they are used and
approved for use by a local authority who has jurisdiction.
WARNING
–
EXPLOSION HAZARD. DO NOT CONNECT OR DISCONNECT
WHEN ENERGIZED.
SYSTEM INFORMATION
The Fireye FX series servo motors are precision actuators designed to accurately position valves and
dampers. The servo motor interprets Modbus commands from an external control and uses a stepper
motor to drive to the commanded position.
The FX series servo motors offers maximum output torque ratings of 4Nm/3ft.-lb., 20Nm/15ft.-lb. or
50Nm/37ft.-lb. The fastest available travel time is 30 seconds for 90 degrees of rotation. The slowest
travel time available varies by size. Maximum rotation angle of the drive shaft is 100 degrees.
The servo is designed to be applied to drive any type of flow control valve or damper as long as the
output torque is suited to the application.
Before attempting to install, commission or operate this equipment all relevant sections of this document
must be read and fully understood, failure to follow them could damage the product or cause a hazardous
condition. If in doubt about any requirements consult the supplier.
© 2022 Carrier 2
Check the ratings in the following instructions to ensure the product is suitable for your application.
Installation, commissioning or adjustment of this product MUST be carried out by personnel qualified by
local, state, regional or national requirements.
After installation is complete, check the product operation is as described in these instructions.
The manufacturer of this equipment accepts no liability for any consequences resulting from
inappropriate, negligent or incorrect installation, commissioning or adjustment of operating parameters of
the equipment.
These mounting and operating instructions are intended to give the knowledge which is necessary to
carry out the mounting and adjustment of FX series servo motor safely and correctly.
NOTE: The manufacturer of this equipment has a policy of continual product improvement and reserves
the right to change the specification of the equipment and the contents of this manual without notice.
TECHNICAL DATA FX04 VERSIONS
Fastest actuating time for 90° angle of rotation: 30 seconds
Slowest actuating time for 90° angle of rotation: 126 seconds
Nominal torque: 4Nm/3ft.-lb.
Maximum angle of rotation: 100°
Nominal voltage 24 VDC ± 10%
Nominal power consumption: 5W nominal, 7.5W peak
Angle of rotation limited by: Firmware
Degree of protection: NEMA 4 IP 65 (see note below)
Installation orientation: Any
Working temperature range: -4°F to +140°F (-20°C to +60°C)
Duty cycle: 100%
Weight: 2.27 lb. / 1.03 kg.
Note: For models without quick disconnect fittings, suitable conduit fittings that meet the desired
protection are supplied by the application.
© 2022 Carrier 3
TECHNICAL DATA FX20 VERSIONS
Fastest actuating time for 90° angle of rotation: 30 seconds
Slowest actuating time for 90° angle of rotation: 368.4 seconds
Nominal torque: 20Nm/15ft.-lb.
Maximum angle of rotation: 100°
Nominal voltage 24 VDC ± 10%
Nominal power consumption: 15W nominal, 35W peak
Angle of rotation limited by: Firmware
Degree of protection: NEMA 4 IP 65 (see note below)
Installation orientation: Any
Working temperature range: -4°F to +140°F (-20°C to +60°C)
Duty cycle: 100%
Weight: 5.43 lb. / 2.46 kg.
Note: For models without quick disconnect fittings, suitable conduit fittings that meet the desired
protection are supplied by the application.
TECHNICAL DATA FX50 VERSIONS
Fastest actuating time for 90° angle of rotation: 30 seconds
Slowest actuating time for 90° angle of rotation: 202.1 seconds
Nominal torque: 50Nm/37ft.-lb.
Maximum angle of rotation: 100°
Nominal voltage 24 VDC ± 10%
Nominal power consumption: 20W nominal, 38W peak
Angle of rotation limited by: Firmware
Degree of protection: NEMA 4 IP 65 (see note below)
Installation orientation: Any
Working temperature range: -4°F to +140°F (-20°C to +60°C)
Duty cycle: 100%
Weight: 6.10 lb. / 2.77 kg.
Note: For models without quick disconnect fittings, suitable conduit fittings that meet the desired
protection are supplied by the application.
© 2022 Carrier 4
ORDERING INFORMATION
Servos for NXF4000/PPC4000 Parallel Positioning System (56k Baud) Bulletin
FX04 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 56k baud for NXF4000/PPC4000
NEX-3001
FX04-1 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, quick disconnect connectors,
minimum travel time of 30 seconds for 90°, 56k baud for NXF4000/PPC4000
FX20 Servo motor, 24 VDC operation, 20Nm, 15 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 56k baud for NXF4000/PPC4000
FX20-1
Servo motor, 24 VDC operation, 20Nm, 15 ft.lb. torque, quick disconnect
connectors, minimum travel time of 30 seconds for 90°, 56k baud for
NXF4000/PPC4000
FX50 Servo motor, 24 VDC operation, 50Nm, 37 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 56k baud for NXF4000/PPC4000
FX50-1
Servo motor, 24 VDC operation, 50Nm, 37 ft.lb. torque, quick disconnect
connectors, minimum travel time of 30 seconds for 90°, 56k baud for
NXF4000/PPC4000
Servos for PLC or General Modbus Use (19.2k, 38.4k Baud) Bulletin
FX04-19 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
NEX-3001
FX04-119 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, quick disconnect connectors,
minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
FX04-38 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 38.4k baud for PLC control
FX04-138 Servo motor, 24 VDC operation, 4Nm, 3 ft.lb. torque, quick disconnect connectors,
minimum travel time of 30 seconds for 90°, 38.4k baud for PLC control
FX20-19 Servo motor, 24 VDC operation, 20Nm, 15 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
FX20-119 Servo motor, 24 VDC operation, 20Nm, 15 ft.lb. torque, quick disconnect
connectors, minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
FX50-19 Servo motor, 24 VDC operation, 50Nm, 37 ft.lb. torque, ½” NPT conduit threaded,
minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
FX50-119 Servo motor, 24 VDC operation, 50Nm, 37 ft.lb. torque, quick disconnect
connectors, minimum travel time of 30 seconds for 90°, 19.2k baud for PLC control
Premade Quick Disconnect Cord Sets Bulletin
59-565-6 Quick disconnect cord set, 6 feet, PVC jacket, temperature rating -40°C to 105°C,
meets NEMA 1,3,4,6P and IEC67 133-748
59-565-40 Quick disconnect cord set, 6 feet, PVC jacket, temperature rating -40°C to 105°C,
meets NEMA 1,3,4,6P and IEC67
Connectors and Cable Bulletin
129-192 Quick disconnect connector for field wiring, female (cable 59-565 recommended) 133-747
129-194 Quick disconnect connector for converting servos, male n/a
59-565 Cable, twisted pair with drain wire, 2 power wires, suitable for servo hookup n/a
© 2022 Carrier 5
SAFETY ADVICE
Device safety
The servo motor must only be used for purposes corresponding to its construction and within the values
specified in the technical data.
The installer should be satisfied that no potential hazards will be produced for any devices or machines
involved as a result of the installation or commissioning.
Before mounting the servo motor, check the free movement of the connected valve, damper or other
device.
After completing the mounting and adjustment, check the correct functioning of the servo motor.
Safety advice for mounting and adjustments
The installer must be satisfied that no potential hazards will be produced for personnel or the environment
as a result of the installation or commissioning.
After completing adjustments, check the correct functioning of the servo motor.
Check that any safety devices are functioning correctly.
Carry out adjustments only in accordance with the instructions described in this document.
Adjustments must be carried out only by a licensed or a qualified person having adequate training, who is
aware of potential hazards.
Wiring
Five wires must be connected to power and communicate with the servo. Quick disconnecting cord sets
are available for the FX04-1, FX04-119, FX04-38, FX04-138, FX20-1, FX20-119, FX50-1 and FX50-119.
Quick disconnect fittings and cable are available for field construction and installation using the ½” NPT
fitted models. Be sure to connect the ground connection first to eliminate any ESD (electrostatic
discharge) potential.
© 2022 Carrier 6
SERVO MOTOR DIAGRAM
FX04 (FX04-1/FX04-119/FX04-138 with quick disconnects shown) diagram
FX20 (FX20-1/FX20-119 with quick disconnects shown) diagram
90°
90°
© 2022 Carrier 7
FX50 (FX50-1/FX50-119 with quick disconnects shown) diagram
© 2022 Carrier 8
DIMENSIONS
FX04 dimensions
© 2022 Carrier 9
FX20 dimensions
© 2022 Carrier 10
FX50 dimensions
Dieses Handbuch passt für folgende Modelle
14
Inhaltsverzeichnis
Andere Fireye Controller Handbücher
Fireye
Fireye D10 Series Bedienungsanleitung
Fireye
Fireye MicroM Series Bedienungsanleitung
Fireye
Fireye PPC6000 Series Betriebsanleitung
Fireye
Fireye SB Series Bedienungsanleitung
Fireye
Fireye SureFire II Bedienungsanleitung
Fireye
Fireye NEXUS NX6100 series Bedienungsanleitung
Fireye
Fireye NEXUS NX6100 series Bedienungsanleitung
Fireye
Fireye PPC6000 Series Bedienungsanleitung
Fireye
Fireye PPC5000 Bedienungsanleitung
Fireye
Fireye PPC6000 Series Handbuch
