Fireye NEXUS NX6100 series Bedienungsanleitung

NX6100

SERIES

INTEGRATED

BURNER

CONTROLLER

DESCRIPTION

The Fireye NEXUS NX6100 Integrated Controller is a microprocessor based, Flame Sa eguard and

Parallel Positioning Combustion Controller built into one compact, user con igurable package. The system

consists o the Controller, Display, Temperature / Pressure Sensors, Servo-Motors and optional Com ire

So tware.

The Flame Sa eguard portion o the control package provides burner sequencing including sa e start

check, proo o main valve closure, selectable main gas sa ety proving sequence, supervised pre-purge,

low ire starting position, pilot and main trials or ignition, main lame supervision, and post purge. Sa ety

event timings are provided to meet North American and CE Standards. Time proven Fireye Flame

Scanners and ampli ication circuits using UV, UV-Sel Check and In rared sensors, provide ast reliable

scanning o most commonly burned uels. For exotic uels and applications, the NX6100 is also

compatible with Fireye Phoenix and Insight Integrated Flame Scanners. Seven low voltage and two line

voltage user de ined auxiliary inputs provide supervision o sa ety critical and non-sa ety critical inputs. A

large menu o alarm messages provides enhanced diagnostics.

Control o up to our pro iles using an independent Servo-Motor or each controlled element allows precise

positioning, accurate to 0.1

, o the uel and air metering devices over the burner’s iring range. Each

pro ile can be de ined to include up to 10 servomotors. Pro iles can be con igured to share common uel

servomotors or as independent (one pro ile per uel) and are not limited by uel. Up to 24 positions per

pro ile including: Closed, Purge, Ignition (Pre erred Start), Low Fire and an additional 20 intermediate

points rom low to high ire. Each individual servomotor’s position and speed are veri ied and lockout will

occur should either o these parameters be exceeded. All servomotors are controlled via secure CANbus

communications link.

Modulation control is provided via the pressure/temperature sensor’s input. The Fireye NX1025, NX1030

or NX1040 sensors provide checking circuits or ail sa e operation. Two PID setpoints are available or

the chosen modulation input, selectable up to two decimal points. Track modulation is available or those

applications requiring less precise control.

The NX6220 and NX6330 Twelve-Key Display allows commissioning and current status o the system

through the use o its tactile membrane keypad. Multi- unction keys allow the commissioning engineer the

ability to access the various Ratio Modes and Option Select menus. The our-line OLED Display clearly

illuminates the Control Variable, Firing Mode, Fuel Selected and Hours Run. It urther allows the Boiler

Operator access to the Auto/Manual selector, Motor Data (servo positions) and other operational

parameters such as System Sequence Position, Valve Proving Sequence Status, Gas Pressure, Flame

Signal, Modulation Rate and Setpoint, as necessary.

Multiple Boiler Sequencing is accomplished through an RS485 Communications bus using Com ire

so tware. Lead/Lag and Standby set points or up to our (4) boilers can be con igured.

NEX-6101

December 12, 2018

Safety information

WARNING

When this equipment is itted to an appliance due regard must also be given to the requirements o that

appliance.

Before attempting to in tall, commi ion or operate thi equipment all relevant ection of thi

document mu t be read and fully under tood. If in doubt about any requirement con ult Fireye.

In tallation, commi ioning or adju tment of thi product MUST be carried out by uitably trained

engineer or per onnel qualified by training and experience.

After in tallation or modification to the in tallation all function of the equipment MUST be checked to

en ure afe and reliable operation of the control.

The manu acturer o this equipment accepts no liability or any consequences resulting rom inappropriate,

negligent or incorrect installation, commissioning or adjustment o operating parameters o the equipment.

Control panels mu t not be le t uncovered while power is on. I it is essential to do so while recti ying aults

only personnel quali ied by training and experience should be involved.

The time any covers are o must be kept to a minimum and warning notices mu t be posted.

Be ore attempting any work on this equipment or any equipment controlled by or connected to this equipment,

all related electrical supplies mu t be isolated.

Sa ety interlocks mu t not be removed or over-ridden. Any aults once detected mu t be corrected be ore the

control is operated.

CAUTION – SOME VERSIONS OF THIS EQUIPMENT CONTAIN A LITHIUM BATTERY

IN THE DISPLAY UNIT

NOTE

The manu acturer o this equipment has a policy o continual product improvement and reserves the right to

change the speci ication o the equipment and the contents o this manual without notice.

The equipment described in this manual is capable o causing property damage, severe injury, or

death. It is the responsibility o the owner or user to ensure that the equipment described herein is

installed, operated and commissioned in compliance with the requirements o all national and local

legislation, which may prevail.

Table of content

This manual - NX6101, describes the installation, commissioning, operation and maintenance o the NX6100

integrated burner controls.

Plea e read the afety information at the front of thi manual before proceeding.

Note: The ymbol in Section 5.5.1 highlight the minimum Option Parameter required

to et up the NX6100

Technical pecification 11

1.1

General 11

1.2

Servo motor control – IMPORTANT: See Section 3.2 11

1.3

Digital output (NX6100 and optional daughter board – P/N - NXDBVSD) 12

1.4

Alarm output (NX6100) 13

1.5

Digital input 13

1.6

Pre ure/temperature input 14

1.7

Auxiliary Analog Input 14

1.8

Ga pre ure input 14

1.9

Flame en ing device 15

1.10

Communication interface 15

1.11

Fireye NX1020-1,-2 ga pre ure en or 15

1.12

Fireye NX1030-1,-2 and NX1034-1,-2 team pre ure en or 16

1.13

Fireye NX1040-1 and NX1044-1 boiler temperature en or 16

1.14

Fireye NXC04, NXC12, NXC20, NXC40 Servo Motor 17

1.15

Fireye NXO2INT Oxygen Probe Interface Unit (optional) 17

1.16

Fireye NXIATS Ambient Air Temperature Sen or (optional) 18

1.17

Fireye NXDBVSD Variable Speed Drive (VSD) Daughter Board (optional) 18

1.18

Approval 18

1.19

Part Li t with De cription 19

In tallation 21

2.1

Mechanical mounting detail for the NX6100 22

2.2

Mechanical mounting detail for the di play module. 22

2.3

Mounting detail for optional Oxygen Probe Interface unit 23

2.4

Mounting arrangement for Temperature, Ga pre ure and Steam pre ure en or 24

2.4.1

Boiler temperature sensors 24

2.4.2

Gas pressure sensors 24

2.4.3

Steam pressure sensors 25

2.4.4

Oxygen probe description 26

2.5

In tallation of oxygen probe 27

2.5.1

Mounting the oxygen probe 27

2.6

Option link election (NX6100) 28

2.6.1

General 28

2.6.2

Line supply voltage (LK1 - 4) (NX6100) 30

2.6.3

SENS IN and SENS SUPP (boiler temp/pressure sensor) (NX6100) 30

2.6.4

REMOTE SETPOINT (NX6100) 31

2.6.5

RS485 serial communications termination resistor (NX6100) 31

2.6.6

Isolated (MODbus) RS485 serial communications termination resistor (daughter

board) 31

2.7

Wiring 31

2.7.1

General 31

2.7.2

Grounding cable screens. 35

2.7.3

GROUND (EARTH) connection 36

2.7.4

Ground (earth) Connection (display unit) 36

2.7.5

Ground (earth) Connection (oxygen probe interface) 36

2.7.6

Ground (earth) Connection (servo motors and sensors) 36

2.7.7

Terminal Designation 37

2.7.8

LIVE and NEUTRAL supply (NX6100) 42

2.7.9

Burner an output (NX6100) 42

2.7.10

Ignition, main valves, pilot valve, vent and pump (NX6100) 42

2.7.11

Auxiliary Relay Outputs (display) 43

2.7.12

Burner select input (NX6100) 43

2.7.13

Fuel and Pro ile Select inputs (optional) (NX6100) 44

2.7.14

Low Voltage Digital Inputs 1 to 7 (NX6100) 45

2.7.15

Low Voltage Air Flow Input (NX6100) 45

2.7.16

Servo motor and Display Connection (NX6100) 45

2.7.17

Pressure sensor screen termination 47

2.7.18

Pressure/temperature sensor input (NX6100) 47

2.7.19

Gas pressure sensor input (NX6100) 48

2.7.20

UV lame scanner 48

2.7.21

Photocell/ I.R. lame scanner 48

2.7.22

Remote Setpoint (Analog Input 5) (NX6100) 49

2.7.23

Analog Input 1 to 3 (NX6100) 49

2.7.24

RS485 inter ace (NX6100) 50

2.7.25

Variable Speed Drive Selection: 51

2.7.26

Variable Speed Drive Daughter Board P/N NXDBVSD. 52

2.7.27

LIVE and NEUTRAL supply external inter ace – P/N NXO2INT 53

2.7.28

Oxygen probe connection (optional Oxygen Probe nterface unit) 53

2.7.29

Inlet temperature sensor (optional) 55

2.8

Final check 56

Servo-motor election and calibration 57

3.1

Servo-motor election 57

3.1.1

Motor requirements 57

3.2

IMPORTANT: Servo-motor direction warning 58

3.3

Locking the ervo-motor to the valve haft 59

3.4

Feedback potentiometer 59

3.5

Adju ting micro witch po ition 60

3.6

Servomotor Replacement 61

De cription of operation 62

4.1

OLED (Organic LED) Di play & Keypad option 62

4.2

Start-up equence 63

4.3

Ga afety valve proving equence (VPS) 68

CLOSEDD 69

4.4

Modulation 69

4.4.1

Normal/Remote mode. 69

4.4.2

Local mode. (LOC 1, LOC 2) 69

Commi ioning the control 70

5.1

General 70

5.2

Commi ioning data 71

5.2.1

Option parameters 71

5.2.2

Setpoints 71

5.3

The Commi ioning proce 71

5.3.1

Navigation 71

5.4

De cription of Touch creen operation. 73

5.4.1

The Touchscreen 73

5.4.2

Touchscreen Power on. 73

5.4.3

The Operation Mode line and Status messages 73

5.4.4

Touchscreen Overview display. 75

5.4.5

Touchscreen Lockout Reset (Alarm Mute) Function. 76

5.4.6

Touchscreen LED Indication. 76

5.4.7

Touchscreen Fuel/Pro ile Select. 77

5.4.8

Touchscreen ‘Control’ screen. 78

5.4.9

Touchscreen ‘Menu’ button. 78

5.4.10

Touchscreen ‘Burner Settings’ button. 79

5.4.11

Touchscreen ‘Fault/Event Log’ button. 80

5.4.12

Touchscreen ‘Screen Con iguration’ button. 80

5.4.13

Cleaning the Touchscreen 81

5.4.14

Touchscreen Commission mode. 82

5.5

U ing option et mode 84

5.5.1

Option parameter list 84

Option 00.1 - Site passcode (0 - 999) DEFAULT VALUE is 154. LV3 84

Option 00.2 - Serial communications control address (0 - 15) LV3 84

Option 00.3 - Reset hours run (0 - 1) LV3 85

Option 00.4 – User program select (0 / 1) LV1 85

Option 00.6 – Reserved 85

Option 00.7 – MODBUS device address (1 – 99) LV3 85

Option 00.8 – MODBUS communications speed (0 – 3) LV3 86

Option 01.0 – Power Up Option (0 - 30) LV3 86

Option 01.1 – Keyboard Auto/Manual enable (0 - 1) LV3 [Engineer’s Key 33] 86

Option 01.2 – Mute/Reset Input enable (0 - 2) LV3 86

Option 01.3 – External pro ile select enable (0 - 2) LV3 87

Option 01.4 – Gas Valve Proo o Closure select (1 - 13) LV3 87

Option 01.5 – Oil Valve Proo o Closure select (0 - 13) LV3 88

Option 01.6 – Second Air low switch enable (0 - 3) LV3 88

Option 01.7 – Sa ety time con iguration set (0 - 1) 89

Option 01.8 – Reserved 89

Option 02.x – Drive Name LV3 90

Option 03.x – Drive Serial Number LV3 91

Option 04.x – Drive Usage In ormation LV3 91

Option 05.x – Drive Options LV3 92

Options 06.1-06.4 – Pro ile Naming LV3 92

Option 07.0 – Fan On Early Time (0 to 120 seconds) LV3 93

Option 07.1 – Air Proving Time (t1) (5 to 120 seconds) LV3 93

Option 07.2 – Pre-Purge Time (t2) (5 to 300 seconds) LV3 93

Option 07.3 – Pre-Ignition Time (t3) (0 to 10 seconds) LV3 93

Option 07.4 – Pilot Ignition Time (t4) (1 to 10 seconds) LV3 94

Option 07.5 – Pilot Hold Time (t5) (1 to 30 seconds) LV3 94

Option 07.6 – Main Ignition Time (t6) (1 to 10 seconds) LV3 94

Option 07.7 – Ignition Hold Time (t7) (1 to 30 seconds) LV3 95

Option 07.8 – Low Fire Hold Time (t8) (0 to 999 seconds) LV3 95

Option 07.9 – Post Purge Time (t9) (0 to 999 seconds) LV3 95

Option 08.0 – Ignition Spark Output Check (0 - 1) LV3 96

Option 08.1 – Flame Failure Response Time (t9) (0-3 seconds) LV3 96

Option 08.2 – Extend False Flame Response Time (t9) LV3 96

Option 09.0 - Inverter control accuracy (0 / 1) LV3 97

Option 09.1 - Inverter error tolerance (0 / 1) LV3 97

Option 09.2 - Inverter closed loop gain (15 – 125%) LV3 97

Option 09.3 - Inverter stop time (0 – 100 seconds) LV3 98

Option 09.4 - Inverter acceleration time (0–100 seconds) (60 seconds max.

recommended) LV3 98

Option 09.6 – VSD2 Speed Encoder Scaler (255 - 999) LV3 98

Option 09.7 – Reserved 99

Option 09.8 – Reserved 99

Option 10.0 - Gas pressure select (0 - 4) LV3 99

Option 10.1 - Gas pressure sensor span (mbar, bar, inches o water, PSI) LV3 100

Option 10.2 - Gas pressure nominal (mbar, bar, inches o water, PSI) LV3 100

Option 10.3 - Gas pressure low limit (mbar, bar, inches o water, PSI) LV3 100

Option 10.4 - Gas pressure high limit (mbar, bar, inches o water, PSI) LV3 100

Option 10.5 - Test volume (0.0 - 99.9 liters or 0 to 999 cubic inches) LV3 100

Option 10.6 - Maximum permissible leakage rate (0 - 99.9 liters per hour or 0 to 999 cubic

inches per hour) LV3 100

Option 10.7 - Vent valve select (0 - 2) LV3 100

Option 10.8 – Valve proving selection (0 - 360) LV3 100

Option 12.0 - Flame detection device I.R. or Direct coupled (0 – 2) LV3 101

Option 12.1 – Pilot Flame Threshold Photocell or I.R. (1 -100) LV3 102

Option 12.2 – Main Flame Threshold Photocell or I.R. (0 – 100) LV3 102

Option 13.0 - Flame detection device U.V. or Sel -Check (shuttered) U.V.

(0 – 2) LV3 102

Option 13.1 – Pilot Flame Threshold U.V. or Shuttered U.V. (0 – 100) LV3 103

Option 13.2 – Main Flame Threshold U.V. or Shuttered U.V. (0 – 100) LV3 103

Option 14.0 – Primary Fault Relay (0 - 8) LV3 103

Option 14.1 – Limit Relay (0 - 8) LV3 103

Option 14.2 – Oxygen and Flue Temperature Limit Relay (0 - 8) LV3 104

Option 14.3 – Permanent gas pilot select (0 - 1) LV3 105

Option 14.4 – Pilot with/without main valve select (0 – 1) LV3 105

Option 14.5 – Direct Ignition on Oil (0 - 1) LV3 105

Option 14.6 – Spark Termination (0-3) LV3 105

Option 14.7 – Aux / Oil Pump Relay Function. (0 - 6) LV3 106

Option 14.8 – Extended Oil Pilot (0-15 seconds) LV3 106

Option 15.0 - Modulation sensor input type (0 - 3) LV3 106

Option 15.1 – Modulation input decimal places (0 to 2) 107

Option 15.2 – Modulation input zero value (-999 to +999 / -99.9 to +99.9 / -

9.99 to +9.99) LV3 107

Option 15.3 – Modulation input span value (-999 to +999 / -99.9 to +99.9 /

-9.99 to +9.99) LV3 108

Option 15.4 – Setpoint display units (0 – 3) LV3 108

Option 15.5 - Boiler high sa ety limit (0 - 999 / 0.0 - 99.9 / 0.00 – 9.99) LV3 108

Option 15.6 – Modulation Time (0 – 120 seconds) LV3 108

Option 15.7 – Bumpless Trans er (0 or 1) LV3 108

Option 15.8 – Low be ore O (0 or 1) LV3 109

Option 15.9 - reserved 109

Option 16.2 – Allow pro ile swap (0 to 16) LV3 110

Option 16.3 – High voltage Input 12 Alarm / Lockout Function (0 - 360) LV3 110

Option 16.4 – High voltage Input 13 Alarm / Lockout Function (0 - 360) LV3 110

Option 16.5 – High voltage Input 12 Fail-sa e Alarm / Lockout Display Messages (0 - 999)

LV3 110

Option 16.6 – High voltage Input 13 Fail-sa e Alarm / Lockout Display Messages (0 - 999)

LV3 110

Option 17.0 – Relay output unction LV3 111

Option 18.1 to 18.9 – Low Voltage Fail-sa e Alarm / Lockout Inputs (0 – 360) and option

parameters 16.3 & 16.4. LV3 115

Option 19.1 to 19.9 – Fail-sa e Alarm / Lockout Display Messages and option parameters

16.5 & 16.6. LV3 116

Option 20.0 – Set-point Select input (0 - 35) LV3 117

Option 20.1 – Boiler Shutdown input (0 - 35). LV3 119

Option 20.2 – Low Fire Hold input (0 - 35). LV3 119

Option 20.3 – Oxygen Trim Disable input (0 - 35). LV3 119

Option 20.4 – Ignition Wait input (0 - 35). LV3 119

Option 20.5 – Purge Hold input (0 - 35). LV3 119

Option 20.6 – Purge Time Start input (0 - 35). LV3 120

Option 20.7 – Analog Input 5 unction (0 - 2). LV3 120

Option 20.8 – Digital Input - Lead Boiler Select (0 – 35) LV3 120

Option 21.0 – Set-point 1 enable (0 - 1) LV1 121

Option 21.1 – Set-point 1 control value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99)

LV1 121

Option 21.2 – Set-point 1 proportional band (0 - 999 / 00.0 - 99.9 / 0.00 -

9.99) LV1 121

Option 21.3 – Set-point 1 integral time (0 – 999 seconds) LV1 121

Option 21.4 – Set-point 1 derivative time (0 – 999 seconds) LV1 121

Option 21.5 - Setpoint 1 control limit type (0 - 2) LV3 121

Option 21.6 - Setpoint 1 low limit control value (Cut In) (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99)

LV1 122

Option 21.7 - Setpoint 1 high limit control value (Cut Out) (0 - 999 / 00.0 - 99.9 / 0.00 -

9.99) LV1 122

Option 21.8 – Remote Setpoint 1 zero (4ma) value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 122

Option 21.9 – Remote Setpoint 1 span (20mA) value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99)

LV1 122

Option 22.0 – PID (set-point) 2 enable (0 - 1) LV1 122

Option 22.1 – Set-point 2 control value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 122

Option 22.2 – Set-point 2 proportional band (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 122

Option 22.3 – Set-point 2 integral term (0 – 999 seconds) LV1 122

Option 22.4 – Set-point 2 derivative term (0 - 100) LV1 123

Option 22.5 - Setpoint 2 control limit type (0 - 2) LV3 123

Option 22.6 - Setpoint 2 low limit control value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 123

Option 22.7 - Setpoint 2 high limit control value (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 123

Option 22.8 – Maximum modulation rate 123

Option 22.9 – Reserved 123

Option 23.0 – Warming Enable (0 or 1) LV1 124

Option 23.1 – Warming Limit (0 - 999 / 00.0 - 99.9 / 0.00 - 9.99) LV1 124

Option 23.2 – Warming Time (0 to 999 minutes) LV1 124

Options 24.x – Sequencing 124

Option 24.0 Sequence Slaves (number o boilers) (0-3) LV1 126

Option 24.1 -24.3 Priority Number(s) LV1 126

Option 24.4 – Lead OFF Time LV1 126

Option 24.5 – Lead (master) Boiler Select Method LV1 126

Option 24.6 – lag (slave) On Rate (0-100%) LV1 127

Option 24.7 – lag (slave) On Delay (0-999 minutes) LV1 127

Option 24.8 – lag (slave) O Rate (0-100%) LV3 127

Option 24.9 – lag (slave) O Delay (0-999 minutes) LV3 127

Option 25.0 – Banking based on temperature / water temperature standby or steam boiler

LV3 127

Option 25.1 – Water temperature zero value LV3 128

Option 25.2 – Water temperature span value LV3 128

Option 25.3 – Water temperature cut-in LV1 128

Option 25.4 – Water temperature cut-out LV1 128

Option 25.5 – Temperature based warming limit LV1 128

Option 25.6 – Lag wait time LV1 128

Option 28.0 – Analog Input 1 decimals (0-2) LV3 128

Option 28.1 – Analog Input 1 zero (0-999) LV3 128

Option 28.2 – Analog Input 1 span (0-999) LV3 128

Option 28.3 – Analog Input 2 decimals (0-2) LV3 129

Option 28.4 – Analog Input 2 zero (0-999) LV3 129

Option 28.5 – Analog Input 2 span (0-999) LV3 129

Option 28.6 – Analog Input 3 decimals (0-2) LV3 129

Option 28.7 – Analog Input 3 zero (0-999) LV3 129

Option 28.8 – Analog Input 3 span (0-999) LV3 129

Option 29.0 – 4-20mA Output 1 unction i not VSD LV3 129

Option 29.1 – Output1 zero value (4mA output) LV3 130

Option 29.2 – Output1 span value (20mA output) LV3 130

Option 29.3 – 4-20mA Output 2 unction i not VSD LV3 130

Option 29.4 – Output2 zero value (4mA output) LV3 130

Option 29.5 – Output2 span value (20mA output) LV3 130

Option 29.6 – 4-20mA Output 3 unction i not VSD LV3 130

Option 29.7 – Output3 zero value (4mA output) LV3 130

Option 29.8 – Output3 span value (20mA output) LV3 131

Option 30.0 – Oxygen probe inter ace serial number LV3 133

Option 30.1 - Oxygen probe calibration o set value (0 – 999) LV3 133

Option 30.2 - Oxygen probe calibration gain value (0 – 999) LV3 133

Option 30.4 – Flue and inlet sensor temperature units (0 – 1) LV3 134

Option 30.5 - Oxygen input unction (0/1) LV3 134

Option 30.6 - Oxygen probe calibrate enable (0 – 2) LV3 134

Option 30.7 - Boiler transport delay (5 – 60 seconds) LV3 135

Option 30.8 - Reset oxygen trim pro ile (0/1) LV3 135

Option 30.9 – Automatic trim commissioning (0 / 1) LV3 135

Options 31.1 to 31.4 - Trim Type or pro iles 1 to 4 (0 to 2) LV3 137

Option 32.0 - Trim limit de ault (0/1) LV3 138

Options 33.1 to 33.4 - Trim integral gain (De ault 10%) LV3 138

Option 34.0 - Trim proportional gain (0/1) LV3 139

Options 34.1 to 34.4 - Trim proportional gain (0.0 – 99.9%) LV3 139

Option 34.5 - Calculating and entering the low values manually LV3 139

Option 35.0 – Inlet temperature sensor serial number LV3 142

Options 35.5 to 35.8-Calori ic values o uels/pro iles 1 to 4 respectively (0.0 – 99.9) LV3 142

Option 35.9 - Boiler radiated heat loss (0.0 – 9.9%) LV3 143

Option 36.0 - Flue temperature alarm select (0/1) LV3 143

Options 36.1 to 36.4 - Flue temperature low alarm values (0 – 999) LV3 143

Option 38.0 - Oxygen alarm select (0 – 2) LV3 144

Options 38.1 to 38.4 - Oxygen low alarm values at low ire (0.0 – 99.9%) LV3 144

Options 39.1 to 39.4 - Oxygen low alarm values at high ire (0.0 – 99.9%) LV3 144

Options 40.1 to 40.4 - Oxygen high alarm values at low ire (0.0 – 99.9%) LV3 144

Options 41.1 to 41.4 - Oxygen high alarm values at high ire (0.0 – 99.9%) LV3 144

Option 42.0 – Second Oxygen probe inter ace serial number LV3 145

Option 42.1 – Second Oxygen probe calibration o set value (0 – 999) LV3 145

Option 42.2 – Second Oxygen probe calibration gain value (0 – 999) LV3 145

Option 42.3 – Second Oxygen probe calibrate enable (0 – 2) LV3 146

Option 42.4 – Max oxygen variation (0 – 9.9 %) LV3 146

Option 42.5 – Max lue temp variation (0 to 999 ºC) LV3 146

Option 42.7 – Air Pressure Input (0-3) LV3 * 147

Option 42.8 – Air Pressure Span (0-99.9) LV3 * 147

Option 42.9 – Air Pressure Error (0-25%) LV3 * 147

Option 43.0 – Enable Water level / expansion unit – Set to 3 or 4 ONLY! LV3 ** 147

Option 43.1 – Unit Address o Water level / expansion unit - Set to 10. LV3 ** 147

Option 44.0 - Set real time clock (0/1) LV1 147

Option 44.1 – Set Year (00 – 99) LV1 148

Option 44.2 – Set Month (1 – 12) LV1 148

Option 44.3 – Set Day o Month (1 – 31) LV1 148

Option 44.4 – Set Day o Week (1 - 7) LV1 148

Option 44.5 – Set Hours (0 - 23) LV1 148

Option 44.6 – Set Minutes (0 - 59) LV1 148

Option 44.7 – Set Seconds (0 - 59) LV1 148

Option 44.9 – Reset Fault Log (0 - 1) LV3 148

Option 45.0 - Erase / Restore enable (0 - 1) LV3 149

Option 45.1 - Erase command (0 - 5) LV3 149

Option 45.2 - Restore command (0 - 999) LV3 150

5.6

Commi ion ratio mode 151

5.6.1

Description 151

5.6.2

Using commission ratio mode 152

5.6.3

Leaving commission ratio mode 153

5.7

Adju t ratio mode 153

5.7.1

Description 153

5.7.2

Entering adjust ratio mode 154

5.7.3

Using adjust ratio mode 154

5.7.4

Leaving adjust ratio mode 155

5.8

Interrogating the oftware i ue 155

Fault and fault finding 156

6.1

The fault di play 156

6.2

What to do when a fault occur 156

6.3

Non-volatile lockout 157

6.4

Fault ub et 157

6.5

Fault li ting 157

6.6

The engineer' key 168

6.6.1

System Event/Fault history. 168

6.6.2

Engineer’s key parameter list 169

6.7

Trouble hooting 181

6.7.1

Display / General 181

6.7.2

Startup 183

6.7.3

Commissioning 183

6.7.4

Gas valve proving 184

6.7.5

Modulation 184

6.7.6

Inverters 185

6.7.7

Oxygen measurement and trim 186

Inverter (variable peed) drive 187

7.1

Sy tem configuration 187

7.2

De cription of control method 188

7.3

Setting up the inverter for u e with the NX6100 erie 188

7.4

Setting up the NX6100 erie for u e with a inverter drive 189

The oxygen trim option 190

8.1

Oxygen Pro probe de cription 190

8.1.1

Installation o oxygen probe 190

8.1.2

Mounting the oxygen probe 191

Appendix 193

9.1

Calibrating and ervicing the oxygen probe 193

9.1.1

Probe calibration 193

9.1.2

Oxygen Probe Filter Testing 194

9.1.3

Removing the oxygen probe rom the lue 194

9.1.4

Filter replacement 195

9.1.5

Probe mounted lue thermocouple replacement. 195

9.2

Trouble hooting inverter problem 197

9.3

PID Tutorial 198

9.4

Combu tion Profile Setup Guideline 199

9.5

Fireye NX6100 Efficiency Calculation 200

9.6

Typical Wiring Diagram 202

9.7

Fireye EP and YP Serie Programmer Equivalent 203

10.

Function Block Programming Detail 204

Introduction to Fireye’ Abacu Programming Software 204

1.1.

Introduction 204

1.4.

The chematic toolbar 208

1.5.

Place Function block 209

1.6.

Moving and editing the link line 209

11.

CANbu Servomotor - Drawing & Template 211

11.1

NXC04 4Nm (3 ft/lb) Servo 211

11.2

NXC12 10Nm (9 ft/lb) Servo 211

11.3

NXC20 20Nm (15 ft/lb) Servo 212

11.4

NXC40 40Nm (30 ft/lb) Servo 213

11.5

NX6110 12 Key Di play 214

11.6

NXTSD104 10.4” Touch creen Di play 215

11.7

NXO2INT Oxygen Interface 216

12.

Circuit board connection 217

12.1

Variable Speed Drive (VSD) Daughter Board P/N NXDBVSD 217

12.2

Oxygen probe connection (optional xygen Probe Interface unit) 218

12.3

Inlet Air Temperature Sen or 219

12.4

NX6100 Terminal Detail 221

Andere Handbücher für NEXUS NX6100 series

Inhaltsverzeichnis

Andere Fireye Controller Handbücher

Fireye

Fireye PPC5000 Bedienungsanleitung

Fireye

Fireye MicroM Series Bedienungsanleitung

Fireye

Fireye SureFire II Bedienungsanleitung

Fireye

Fireye FLAME-MONITOR E110 Bedienungsanleitung

Fireye

Fireye BurnerPRO BP110 Bedienungsanleitung

Fireye

Fireye NEXUS NX6100 series Bedienungsanleitung

Fireye

Fireye PPC6000 Series Handbuch

Fireye

Fireye SB Series Bedienungsanleitung

Fireye

Fireye BurnerPRO BP110 Bedienungsanleitung

Fireye

Fireye FX Series Bedienungsanleitung

Fireye

Fireye D10 Series Bedienungsanleitung

Fireye

Fireye PPC6000 Series Betriebsanleitung

Fireye

Fireye PPC6000 Series Bedienungsanleitung

Fireye

Fireye PPC4000 SERIES Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung