First Alert 1220CV Bedienungsanleitung

First Alert 1220CV Quick Guide

https://alpha.adt.com/help/145[11/12/2018 10:34:02 PM]

First Alert 1220CV - Quick Guide

For a detailed review of the entire system, please view the First Alert 1220CV manual.

« Help Center

Arm &

Disarm the

System

Battery Bypass

Protected

Areas

Chimes &

Beeps

Reset Security

Codes

Trouble

Conditions

Volume

Arm and Disarm

Arm:

To arm all sensors in AWAY mode when you are leaving the premises, enter your code + [2].

To arm in STAY mode when you are not leaving the premises, enter your code + [3].

Disarm:

To disarm, enter your [security code] + [1].

Select

First Alert 1220CV Quick Guide

https://alpha.adt.com/help/145[11/12/2018 10:34:02 PM]

For more information on this topic please visit the complete First Alert 1220CV manual.

Battery

The First Alert 1220CV operates on a Battery Replacement Page.

Bypass Protected Areas

Bypassing a zone allows you to arm your system with certain protected areas intentionally

unarmed or to access a protected area when the system is armed.

To bypass a zone, enter your [security code] + [6] + [two-digit zone number].

To unbypass a zone,§ repeat the bypass procedure or arm and disarm your system.

For more information on this topic please visit the complete First Alert 1220CV manual.

Chimes and Beeps

When your system is in chime mode, a chime alert will sound three tones whenever a

protected door/window is opened.

To turn the door chime function on and off, enter your security code + [9].

Toggle between On and Off.

For more information on this topic please visit the complete First Alert 1220CV manual.

Reset

To clear the display after an alarm event, arm and disarm your system.

Security Codes

Your system allows for additional users, however a user may not delete or change the user

code of the same or higher authority than which they are assigned. For example, a Master user

may only add users to a lower authority level. To change a user’s authority level, that use must

first be deleted and then added again. A user can only be deleted or changed from the within

the partition they are assigned.

To add a user, enter your [Master code] + [8] + 3-digit [new user number] + [new user’s 4-

digit code].

A prompt [ADD NEW USER?] will ask you if the user is new.

First Alert 1220CV Quick Guide

https://alpha.adt.com/help/145[11/12/2018 10:34:02 PM]

A prompt [USER NUMBER ENTER AUTH.LEVEL] will ask you to enter the new user’s

authority level (1-6). Refer to the chart below for User Authority Levels.

If your system has been supplied with a 5800 series button transmitter a prompt [RF

BUTTON?] will ask you if you would like to assign a button one to this user.

If you have assigned a button transmitter, a prompt [ENTER BUTTON ZN#] will ask you to

enter the button’s zone number.

If you yourself have access to other partitions, a prompt [MUTLI-ACESS?] will ask you if

you would like for the new user to have access those same partitions.

A prompt [GLOBAL ARM?] will ask you if you would like for this user to be able to globally

arm, i.e., able to arm more than one partition at the same time.

A prompt [PART 2-SHOP?] will ask you if the user should have access to the next partition.

The keypad will display the new user access information.

To change a user code, enter the [master code] + [8] + [user number to be changed].

Enter the new user code for that user.

To delete a user, enter your [Master code] + [8] + [user number to be deleted]. Wait

approximately three seconds for the keypad to verify.

User

Authority

Code

Explanation Code

Level 1

Master

Can perform all system functions in assigned partitions and can add, delete

or change Manager and Operator level users. Master codes can only be

added by the Installer.

[1]

Level 2

Manager

Can perform system functions in assigned partitions and can add, delete or

change Operator level users. [2]

Level 3

Operator

Can perform system functions in assigned partitions but cannot add or

delete other users. [3]

Level 4

First Alert 1220CV Quick Guide

https://alpha.adt.com/help/145[11/12/2018 10:34:02 PM]

Return to Top

Operator

Same as Operator A, except Operator B cannot bypass zones of protection. [4]

Level 5

Operator

Can arm the system in assigned partitions but cannot disarm the system

unless the system was armed with this code. This code is typically assigned

to a trusted person who may need to arm/disarm the system at certain

times, i.e., a babysitter.

[5]

Level 6

Duress

Using this code to arm or disarm the system will send a silent panic alarm to

the central monitoring station, if that service is connected. [6]

Level 7

Limited

Use

Can arm and disarm the system, but only for a predetermined number of

times, after which, this code automatically expires. [7]

For more information on user access codes, please view the First Alert 1220CV manual.

Trouble Conditions

Trouble conditions are indicated by the word CHECK and continual beeping from the touchpad.

Any key will silence the beeping. A display of CHECK + zone no. may indicate that a problem

requires your attention. Check the specified zone area, close any open doors or windows and

enter your security code and press [OFF]. If your system includes wireless sensors, the CHECK

condition may be caused by some change in the environment of the protected area.

To silence trouble beeps, press any key or enter your security code and press [OFF].

For a complete list of Trouble Conditions, please refer to the Safewatch and Ademco systems

troubleshooting page.

Volume

The volume on the First Alert 1220CV is not adjustable.

How can we help?

Inhaltsverzeichnis

Andere First Alert Tastenfeld Handbücher

First Alert

First Alert FA6150RF Montageanleitung

First Alert

First Alert TouchCenter FA701CVKP Montageanleitung

First Alert

First Alert FA260RF Bedienungsanleitung

First Alert

First Alert FA570CR Montageanleitung

First Alert

First Alert FA270VKP Bedienungsanleitung

First Alert

First Alert FA570RF Bedienungsanleitung

First Alert

First Alert FA560VKP Montageanleitung

First Alert

First Alert FA270RF Bedienungsanleitung

First Alert

First Alert FA210RF Bedienungsanleitung

First Alert

First Alert FA270RF Montageanleitung

First Alert

First Alert FA270VKP Montageanleitung

First Alert

First Alert TouchCenter FA701CKP Bedienungsanleitung

First Alert

First Alert FA215KP Bedienungsanleitung

First Alert

First Alert FA570RF Bedienungsanleitung

First Alert

First Alert FA560VKP Bedienungsanleitung

First Alert

First Alert FA220KP Montageanleitung

First Alert

First Alert FA260KP-OM Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung

Bosch

Bosch D1260 Series Bedienungsanleitung

Elmes Electronic

Elmes Electronic KB1 Bedienungsanleitung

Clare Controls

Clare Controls ClareOne CLR-C1-PNC Montageanleitung