Fisher FIELDVUE DLC3010 Bedienungsanleitung

www.Fisher.com

Fisher™FIELDVUE™DLC3010 Digital Level

Controller

Contents

Installation 2.....................

Mounting 8.......................

Electrical Connections 13...........

Initial Setup 18....................

Calibration 23.....................

Schematics 28....................

Specifications 29..................

Note

This guide describes how to install, setup, and calibrate the DLC3010 using a 475 Field

Communicator. For all other information on this product, including reference materials,

manual setup information, maintenance procedures, and replacement part details refer

to the DLC3010 Instruction Manual (D102748X012). If a copy of this document is required,

contact your Emerson Process Management sales office or visit our website at www.Fisher .com.

For information on using the Field Communicator, see the Product Manual for the Field

Communicator, available from Emerson Performance Technologies.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

This quick start guide applies to:

Device Type DLC3010

Device Revision 1

Hardware Revision 1

Firmware Revision 8

DD Revision 3

W7977-1

Scan or click

to access sales

office information

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Installation

WARNING

To avoid personal injury, always wear protective gloves, clothing, and eyewear when performing any installation

operations.

Personal injury or property damage due to sudden release of pressure, contact with hazardous fluid, fire, or explosion can

be caused by puncturing, heating, or repairing a displacer that is retaining process pressure or fluid. This danger may not

be readily apparent when disassembling the sensor or removing the displacer. Before disassembling the sensor or

removing the displacer, observe the appropriate warnings provided in the sensor instruction manual.

Check with your process or safety engineer for any additional measures that must be taken to protect against process

media.

This section contains digital level controller installation information, including an installation flowchart (figure 1),

mounting and electrical installation information, and a discussion of failure mode jumpers.

Do not install, operate, or maintain a DLC3010 digital level controller without being fully trained and qualified in valve,

actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is

important to carefully read, understand, and follow all of the contents of this manual, including all safety cautions and

warnings. If you have any questions regarding these instructions contact your Emerson Process Management sales

office before proceeding.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Figure 1. Installation Flowchart

START HERE

Factory mounted

on 249 sensor?

Use Setup Wizard

to enter sensor

data and

calibration

condition

Check Alarm

Jumper Position

Mount and Wire

Digital level

Controller

Power

Digital level

Controller

Yes

Install heat

insulator

assembly

High

temperature

application?

Yes

Set Level Offset

to Zero

Calibrate

sensor

Wire

Digital Level

Controller

Power

Digital Level

Controller

Enter Tag, Messages,

Date, and check or set

target application data

Density

Measurement?

Set

Range Values

Using

Temperature

Correction?

Set

Temperature

Units

Setup specific

gravity tables

Set

Specific Gravity

Yes

Using RTD?

Yes Setup and

Calibrate RTD

Enter Process

Temperature

DONE

Disable Writes

NOTE:

1 IF USING RTD FOR TEMPERATURE CORRECTION,

ALSO WIRE RTD TO DIGITAL LEVEL CONTROLLER

2 DISABLING WRITES IS EFFECTIVE ONLY IF THE DLC3010 REMAINS

POWERED‐UP

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Configuration: On the Bench or in the Loop

Configure the digital level controller before or after installation. It may be useful to configure the instrument on the

bench before installation to ensure proper operation, and to familiarize yourself with its functionality.

Protecting the Coupling and Flexures

CAUTION

Damage to flexures and other parts can cause measurement errors. Observe the following steps before moving the sensor

and controller.

Lever Lock

The lever lock is built in to the coupling access handle. When the handle is open, it positions the lever in the neutral

travel position for coupling. In some cases, this function is used to protect the lever assembly from violent motion

during shipment.

A DLC3010 controller will have one of the following mechanical configurations when received:

1. A fully assembled and coupled caged‐displacer system is shipped with the displacer or driver rod blocked within the

operating range by mechanical means. In this case, the access handle (figure 2) will be in the unlocked position.

Remove the displacer‐blocking hardware before calibration. (See the appropriate sensor instruction manual). The

coupling should be intact.

Figure 2. Sensor Connection Compartment (Adapter Ring Removed for Clarity)

PRESS HERE TO

MOVE ACCESS

HANDLE

SLIDE ACCESS HANDLE

TOWARD FRONT OF UNIT

TO EXPOSE ACCESS HOLE

ACCESS HOLE

MOUNTING

STUDS

SHAFT CLAMP

SET SCREW

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

CAUTION

When shipping an instrument mounted on a sensor, if the lever assembly is coupled to the linkage, and the linkage is

constrained by the displacer blocks, use of the lever lock may result in damage to bellows joints or flexure.

2. If the displacer cannot be blocked because of cage configuration or other concerns, the transmitter is uncoupled

from the torque tube by loosening the coupling nut, and the access handle will be in the locked position. Before

placing such a configuration into service, perform the Coupling procedure.

3. For a cageless system where the displacer is not connected to the torque tube during shipping, the torque tube

itself stabilizes the coupled lever position by resting against a physical stop in the sensor. The access handle will be

in the unlocked position. Mount the sensor and hang the displacer. The coupling should be intact.

4. If the controller was shipped alone, the access handle will be in the locked position. All of the Mounting, Coupling

and Calibration procedures must be performed.

The access handle includes a retaining set screw, as shown in figures 2 and 6. The screw is driven in to contact the

spring plate in the handle assembly before shipping. It secures the handle in the desired position during shipping and

operation. To set the access handle in the open or closed position, this set screw must be backed out so that its top is

flush with the handle surface.

Hazardous Area Approvals and Special Instructions for “Safe Use” and

Installations in Hazardous Locations

Certain nameplates may carry more than one approval, and each approval may have unique installation/wiring

requirements and/or conditions of “safe use”. These special instructions for “safe use” are in addition to, and may

override, the standard installation procedures. Special instructions are listed by approval type.

Note

This information supplements the nameplate markings affixed to the product.

Always refer to the nameplate itself to identify the appropriate certification. Contact your Emerson Process Management sales

office for approval/certification information not listed here.

WARNING

Failure to follow these conditions of safe use could result in personal injury or property damage from fire or explosion, or

area re‐classification.

CSA

Special Conditions of Safe Use

Intrinsically Safe, Explosion‐proof, Division 2, Dust Ignition‐proof

Ambient temperature rating: -40_C ≤Ta ≤+80_C; -40_C ≤Ta ≤+78_C; -40_C ≤Ta ≤+70_C

Refer to table 1 for approval information.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Table 1. Hazardous Area Classifications—CSA (Canada)

Certification Body Certification Obtained Entity Rating Temperature Code

CSA

Ex ia Intrinsically Safe

Class I, Division 1, 2 Groups A, B, C, D

Class II, Division 1, 2 Groups E, F, G

Class III

T6 per drawing 28B5744 (see figure 13)

Vmax = 30 VDC

Imax = 226 mA

Ci = 5.5 nF

Li = 0.4 mH

T6 (Tamb ≤80°C)

Explosion-proof

Class I, Division 1 GP B,C,D T5/T6 - - - T5 (Tamb ≤80°C)

T6 (Tamb ≤78°C)

Class I Division 2 GP A,B,C,D T5/T6 - - - T5 (Tamb ≤80°C)

T6 (Tamb ≤70°C)

Class II Division 1,2 GP E,F,G T5/T6

Class III T5/T6 - - - T5 (Tamb ≤80°C)

T6 (Tamb ≤78°C)

Special Conditions of Safe Use

Intrinsically Safe, Explosion‐proof, Non‐incendive, Dust Ignition‐proof

1. This apparatus enclosure contains aluminum and is considered to constitute a potential risk of ignition by impact or

friction. Care must be taken into account during installation and use to prevent impact or friction.

Refer to table 2 for approval information.

Table 2. Hazardous Area Classifications—FM (United States)

Certification Body Certification Obtained Entity Rating Temperature Code

IS Intrinsically Safe

Class I,II,III Division 1 GP A,B,C,D,

E,F,G T5 per drawing 28B5745 (see figure 14)

Vmax = 30 VDC

Imax = 226 mA

Ci = 5.5 nF

Li = 0.4 mH

Pi = 1.4 W

T5 (Tamb ≤80°C)

XP Explosion‐proof

Class I Division 1 GP B,C,D T5

NI Non‐incendive

Class I Division 2 GP A,B,C,D T5

DIP Dust Ignition‐proof

Class II Division 1 GP E,F,G T5

S Suitable for Use

Class II, III Division 2 GP F,G

- - - T5 (Tamb ≤80°C)

ATEX

Special Conditions for Safe Use

Intrinsically Safe

The apparatus DLC3010 is an intrinsically safe apparatus; it can be mounted in a hazardous area.

The apparatus can only be connected to an intrinsically safe certified equipment and this combination must be

compatible as regards the intrinsically safe rules.

Operating ambient temperature: -40_C to + 80_C

Flameproof

Operating ambient temperature: -40_C to + 80_C

The apparatus must be fitted with a certified Ex d IIC cable entry.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Type n

This equipment shall be used with a cable entry ensuring an IP66 minimum and being in compliance with the relevant

European standards.

Operating ambient temperature: -40_C to + 80_C

Refer to table 3 for additional approval information.

Table 3. Hazardous Area Classifications—ATEX

Certificate Certification Obtained Entity Rating Temperature Code

ATEX

Intrinsically Safe

II 1 G D

Gas

Ex ia IIC T5 Ga

Dust

Ex ia IIIC T83°C Da IP66

Ui = 30 VDC

Ii = 226 mA

Pi = 1.4 W

Ci = 5.5 nF

Li = 0.4 mH

T5 (Tamb ≤80°C)

Flameproof

II 2 G D

Gas

Ex d IIC T5 Gb

Dust

Ex tb IIIC T83°C Db IP66

- - - T5 (Tamb ≤80°C)

Type n

II 3 G D

Gas

Ex nA IIC T5 Gc

Dust

Ex t IIIC T83°C Dc IP66

- - - T5 (Tamb ≤80°C)

IECEx

Intrinsically Safe

The apparatus can only be connected to an intrinsically safe certified equipment and this combination must be

compatible as regards the intrinsically safe rules.

Operating ambient temperature: -40_C to + 80_C

Flameproof, Type n

No special conditions for safe use.

Refer to table 4 for approval information.

Table 4. Hazardous Area Classifications—IECEx

Certificate Certification Obtained Entity Rating Temperature Code

IECEx

Intrinsically Safe

Gas

Ex ia IIC T5 Ga

Dust

Ex ia IIIC T83°C Da IP66

Ui = 30 VDC

Ii = 226 mA

Pi = 1.4 W

Ci = 5.5 nF

Li = 0.4 mH

T5 (Tamb ≤80°C)

Flameproof

Gas

Ex d IIC T5 Gb

Dust

Ex t IIIC T83°C Db IP66

- - - T5 (Tamb ≤ 80°C)

Type n

Gas

Ex nA IIC T5 Gc

Dust

Ex t IIIC T83°C Dc IP66

- - - T5 (Tamb ≤80°C)

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Mounting

Mounting the 249 Sensor

The 249 sensor is mounted using one of two methods, depending on the specific type of sensor. If the sensor has a

caged displacer, it typically mounts on the side of the vessel as shown in figure 3. If the sensor has a cageless displacer,

the sensor mounts on the side or top of the vessel as shown in figure 4.

Figure 3. Typical Caged Sensor Mounting

A3789‐1

LIQUID LEVEL

Figure 4. Typical Cageless Sensor Mounting

A3788‐1

The DLC3010 digital level controller is typically shipped attached to the sensor. If ordered separately, it may be

convenient to mount the digital level controller to the sensor and perform the initial setup and calibration before

installing the sensor on the vessel.

Note

Caged sensors have a rod and block installed on each end of the displacer to protect the displacer in shipping. Remove these parts

before installing the sensor to allow the displacer to function properly.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

DLC3010 Orientation

Mount the digital level controller with the torque tube shaft clamp access hole (see figure 2) pointing downward to

allow accumulated moisture drainage.

Note

If alternate drainage is provided by the user, and a small performance loss is acceptable, the instrument can be mounted in 90

degree rotational increments around the pilot shaft axis. The LCD meter may be rotated in 90 degree increments to accommodate

this.

The digital level controller and torque tube arm are attached to the sensor either to the left or right of the displacer, as

shown in figure 5. This can be changed in the field on a 249 sensor (refer to the appropriate sensor instruction

manual). Changing the mounting also changes the effective action, because the torque tube rotation for increasing

level, (looking at the protruding shaft), is clockwise when the unit is mounted to the right of the displacer and counter‐

clockwise when the unit is mounted to the left of the displacer.

All caged 249 sensors have a rotatable head. That is, the digital level controller can be positioned at any of eight

alternate positions around the cage as indicated by the position numbers 1 through 8 in figure 5. To rotate the head,

remove the head flange bolts and nuts and position the head as desired.

Mounting the Digital Level Controller on a 249 Sensor

Refer to figure 2 unless otherwise indicated.

1. If the set‐screw in the access handle is driven against the spring plate, use a 2 mm hex key to back it out until the

head is flush with the outer surface of the handle (see figure 6) . Slide the access handle to the locked position to

expose the access hole. Press on the back of the handle as shown in figure 2 then slide the handle toward the front

of the unit. Be sure the locking handle drops into the detent.

2. Using a 10 mm deep well socket inserted through the access hole, loosen the shaft clamp (figure 2). This clamp will

be re‐tightened in the Coupling portion of the Initial Setup section.

3. Remove the hex nuts from the mounting studs. Do not remove the adapter ring.

CAUTION

Measurement errors can occur if the torque tube assembly is bent or misaligned during installation.

Quick Start Guide

D103214X012

DLC3010 Digital Level Controller

February 2016

Figure 5. Typical Mounting Positions for FIELDVUE DLC3010 Digital Level Controller on Fisher 249 Sensor

SENSOR

CAGED

CAGELESS

RIGHT‐OF‐DISPLACER

LEFT‐OF‐DISPLACER

1 NOT AVAILABLE FOR SIZE NPS 2 CL300 AND CL600 249C SENSOR.

19B2787 Rev. D

19B6600 Rev. C

B1407‐2

Figure 6. Close‐up of Set‐Screw

SET‐SCREW

4. Position the digital level controller so the access hole is on the bottom of the instrument.

5. Carefully slide the mounting studs into the sensor mounting holes until the digital level controller is snug against

the sensor.

6. Reinstall the hex nuts on the mounting studs and tighten the hex nuts to 10 NSm (88.5 lbfSin).

Andere Handbücher für FIELDVUE DLC3010

Inhaltsverzeichnis

Andere Fisher Controller Handbücher

Fisher

Fisher 4194B Series Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC6200 Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC2000 Konfigurationshandbuch

Fisher

Fisher 1032 Bedienungsanleitung

Fisher

Fisher 1098-EGR Bedienungsanleitung

Fisher

Fisher R130/21 Bedienungsanleitung

Fisher

Fisher Fieldvue DVC5010 Bedienungsanleitung

Fisher

Fisher 912 Series Bedienungsanleitung

Fisher

Fisher FIELDVUEDVC6200f Bedienungsanleitung

Fisher

Fisher FIELDBUE DVC6200 Bedienungsanleitung

Fisher

Fisher EMERSON P539 Bedienungsanleitung

Fisher

Fisher 6492HTM Bedienungsanleitung

Fisher

Fisher MR95L Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC6200f Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC6200 Bedienungsanleitung

Fisher

Fisher 2502 Series Level-Trol Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC6200 HW1 Bedienungsanleitung

Fisher

Fisher 655 Bedienungsanleitung

Fisher

Fisher ED Benutzerhandbuch

Fisher

Fisher FIELDVUE DLC3010 Bedienungsanleitung

Fisher

Fisher 1066 Bedienungsanleitung

Fisher

Fisher FIELDVUE DVC6200 Bedienungsanleitung

Fisher

Fisher Fisher Fieldvue DLC3100 Benutzerhandbuch

Fisher

Fisher 667 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung