Flamerite Fires Glazer 600 Bedienungsanleitung

1 | Page

Installation, Precautions & Servicing

Glazer

600 900 1000 1500

IMPORTANT

This product is only suitable for well insulated spaces or occasional use

Carefully remove the fire from the packing checking neither the heater nor the power

cable has been damaged during transport. Do not operate the fire if damaged. Please

bear in mind the weight of the fire before removal from the packaging and installation.

Consider if help is required. Always read this manual first before attempting to install

or use and keep in a safe place. Any alteration to the power cable should only be done

by a qualified electrician.

Your fire is guaranteed for one year from the date of purchase. In the unlikely event of

a breakdown you have access to our customer services team, simply call 01543 251122

during office hours, 9am – 5pm or e-mail on info@flameritefires.com The accessories

are found in a box that is packed at the side of the fire.

2 | Page

•For indoor use only.

•Do not use the fire in the vicinity of a bath, shower or swimming pool.

•Never use the fire to dry laundry.

•Never install the fire directly underneath a fixed main socket.

•Never cover the appliance.

•The use of an extension lead is not recommended.

•This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

•Cleaning and user maintenance shall not be made by children without supervision.

•Children of less than 3 years should be kept away unless continuously supervised

•Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it

has been placed or installed in its intended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe way and understand the hazards

involved.

•Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or

perform user maintenance.

•Some parts of this product can become very hot and cause burns. Particular attention has to be given

where children and vulnerable people are present

•Caution should be applied to ensure that children do not play with the fuel effects.

•As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible,

caution and common sense should be applied when operating your appliance, particularly in the

vicinity of small children.

•CAUTION: The heater is fitted with an automatic cut out to prevent any damage due to overheating.

The element will continually and automatically cut out if the airflow is obstructed. Never cover the air

outlets. To reset, switch the fire off, disconnect from the mains supply, remove the cause of the

overheating, where fitted check the OmniGlide micro switches. Allow to cool for a suitable period

then switch the fire back on.

•CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, the

appliance must not be supplied through an external switching device, such as a timer, or connected to

circuit regularly switched on and off by a utility.

Important Safety Information and Warnings

Where a chimney is not blocked off completely, any draw will cause the heater to cut

out during use. Care should also be taken when fitting into a cavity wall in case of

damp or draft with external air vents fully sealed

3 | Page

Electrical connections. Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement

fuses must be 13A and ASTA approved. If the fuse cover is lost the plug must not be used until a replacement

cover, of the same colour, is obtained from an electrical retailer. The appliance is fitted with a moulded plug if

it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed.

Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as

this could cause a hazard. If the mains cable is damaged it must be replaced by the manufacturer or an

authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code.

Green and yellow:

EARTH

Blue:

NEUTRAL

Red:

LIVE

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in

your plug proceed as follows: -

•The wire which is coloured green and yellow must be connected to the terminal in the plug

which is marked with the letter E, or coloured green or coloured green and yellow, or marked

with the earth symbol

•The wire which is coloured blue must be connected to the terminal in the plug which is marked

with the letter N, or coloured black.

•The wire which is coloured brown must be connected to the terminal in the plug which is marked

with the letter L, or coloured red.

RECYCLING

Please recycle responsibly. Take your item to your local recycling

centre. You can easily locate your nearest centre on

the www.recyclenow.com website or check with your retailer for

details on either a collection service or a store take-back scheme (some

may apply charges). Councils may offer a household recycling

collection service for small electrical items; contact your local authority

for more details.

Electrical Connections

Insert the plug tightly into its IEC connector underneath the fire if not already done

so. If the removal of the plug is absolutely necessary for installation, cut off in an

area within 100mm only of the plug itself. Any further will affect your warranty.

4 | Page

DO NOT TWIST, FORCE OR SQUEEZE THE FIRE DURING THE INSTALLATION PROCESS.

Using in a chimney breast, fireplace or an internal studwork and plaster board wall.

The fire must be well supported in a structure when mounting above the floor. A wall support or lintel should

be fitted at the required height to ensure the appliance does not support the weight of the finished wall or

chimney breast. The height at which you may wish to fix the fire in or on the wall is up to you, we recommend

anywhere from 350-450mm from the floor to the bottom of the fire opening (not the bottom of the fire).

Secure into place using the fixings provided.

Situ Fixings

Stud Wall

3x 60mm screws

Modular Chimney

3x M10 x 50mm Rawl plugs. 3x 60mm screws

Breast

2x 50mm screws & cover caps. 4x 13m screws.

Modular Wall

7x M10 x 50mm Rawl plugs. 7x 60mm screws. 2x M6 x 25mm bolts.

& Freestanding

2x M6 washers. 8x 13mm screws (4 fitted/4 packed)

Modular suite, wall mounting & freestanding

The fire comes with two hanging rails top and bottom to fix the Glazer to the wall. Using the lower bracket

mark the holes, drill with a M10 bit and fit the rawl plugs. Using the 60mm screws, secure the bracket to the

wall.

Position the fire on top of the bottom bracket making sure the corner bolts fit through the slots either side

and can screw into the underside of the fire. With the top bracket attached to the fire, mark across its length

and into the slots above each hole on the back edge. Remove the top bracket and 13mm screws from the fire.

Using as a template mark the holes on the wall, drill and fit the rawl plugs using an M10 bit. Using the 60mm

screws fix the bracket to the wall.

Installation Instructions

5 | Page

Slide the fire into the channel created by the top and bottom brackets. Screw the top bracket back onto the

fire with the 13mm self-tappers and bolt each corner of the bottom bracket through the slots either side into

the fire using the M6 bolts and washer supplied. At this point you will be able to level the fire accordingly at

the base by loosening and tightening the bottom bolts.

If the fire is mounted to the wall, the base will slide on from the front between the flange running around the

opening and the pull-out tabs A. If using in a freestanding suite the fire should be pushed in from the back in

the same way, then the whole suite pushed up against the wall. In both cases make sure the power cable is

firmly pushed into the fire and does not foul the suite when up against the wall.

Using four of the 13mm screws secure the base to the fire along the side flange and fit the décor trim B. The

décor trim is the long black channel that provides a neat edge along the bottom of the fire opening, it is held

in place with magnets.

Fix the gloss black decorative panels either side of the opening to the fire C, also held in place with magnets.

6 | Page

Slide the top from the front Dbetween the flange running around the opening and the pull-out tabs. Make

sure the top of each gloss black decorative panel C fits into the recess around the cut out as the top pushes

back towards the wall. On the underside using four of the 13mm self-tapers provided, secure the sides of the

top only.

CHIMNEY BREAST: The chimney breast requires a baton to be fitted to the wall above the fire using three

M10 x 50mm rawl plugs and 60mm screws. Use an M10 bit to drill the holes. The baton must be fitted from

the top of the fire to the bottom of the baton, dead centre so the chimney breast can comfortably slide over

the fire and line up to the pilot holes either side of the baton.

Height from the top of the fire: 600 = 885mm/900 = 1110mm/1000 = 1040mm

Carefully slide the chimney breast on from the front Dbetween the flange running around the opening and

the pull-out tabs. Make sure the top of each gloss black decorative panel C fit into the recess around the cut

out as the chimney breast pushes back towards the wall. Use the two 50mm screws to secure the chimney

breast to the baton Fand push the white plastic covers over the top. On the underside use four 13mm screws

provided, secure the sides only.

DO NOT HANG HEAVY OBJECTS ONTO THE CHIMNEY BREAST

7 | Page

Stud wall, chimney & fireplace fitting

There must be enough clearance for the fire to comfortably fit into the hole. DO NOT SQUEEZE INTO THE

OPENING this may deform the case and stop the glass from moving correctly.

Converting from 3-sided glass viewing into a 2 or 1 sided glass viewable fire

Each blanking panel consists of two parts that maybe be fitted directly over the glass sides. Remove the 4

screws already fitted and slide into place. Secure and refit the screws through the corresponding holes on the

fire.

Minimum opening to fit and inset the fire

Model

W1side

W2side

W3side

600

725mm

645mm

625mm

610mm

265mm

900

505mm

945mm

925mm

910mm

265mm

1000

575mm

1045mm

1025mm

1010mm

265mm

1500

575mm

1545mm

1525mm

1510mm

265mm

Visible burn area after fitting

Model H W1side W2side W3side

D2/3

side

600

500mm

645mm

625mm

600mm

180mm

900

280mm

945mm

925mm

900mm

180mm

1000

350mm

1045mm

1025mm

1000mm

180mm

1500

350mm

1545mm

1525mm

1500mm

180mm

8 | Page

The logs effects must be positioned according to the images below. Care must be taken to ensure there is

enough room between the front of the logs and the glass channel at the front of the opening so the glass may

tilt open freely into the fire and trigger the micro switch.

Visit www.flameritefires.com/downloads if you require clearer downloadable images.

600

Log Effect

9 | Page

900 & 1000

10 | Page

1500

Andere Handbücher für Glazer 600

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Flamerite Fires Kamin im Innenbereich Handbücher

Flamerite Fires

Flamerite Fires E-FX Bedienungsanleitung

Flamerite Fires

Flamerite Fires Valiant Bedienungsanleitung

Flamerite Fires

Flamerite Fires Gotham 900 Bedienungsanleitung

Flamerite Fires

Flamerite Fires E-FX Bedienungsanleitung

Flamerite Fires

Flamerite Fires OMNIGLIDE Glazer 900 Bedienungsanleitung

Flamerite Fires

Flamerite Fires Luma Series Bedienungsanleitung

Flamerite Fires

Flamerite Fires Corello F01 Bedienungsanleitung

Flamerite Fires

Flamerite Fires OnmiGlide 1300 Bedienungsanleitung

Flamerite Fires

Flamerite Fires Gotham essence 750T Bedienungsanleitung

Flamerite Fires

Flamerite Fires Gotham Series Bedienungsanleitung

Flamerite Fires

Flamerite Fires Cisco Bedienungsanleitung

Flamerite Fires

Flamerite Fires essence Voyager Bedienungsanleitung

Flamerite Fires

Flamerite Fires Glazer 600 Bedienungsanleitung

Flamerite Fires

Flamerite Fires 400 Series Bedienungsanleitung

Flamerite Fires

Flamerite Fires E-FX 1000 Bedienungsanleitung

Flamerite Fires

Flamerite Fires Cisco Extreme Bedienungsanleitung

Flamerite Fires

Flamerite Fires E-FX SL Bedienungsanleitung

Flamerite Fires

Flamerite Fires Essence Corello Bedienungsanleitung

Flamerite Fires

Flamerite Fires Corello Bedienungsanleitung

Flamerite Fires

Flamerite Fires Arlo 400 Series Bedienungsanleitung

Flamerite Fires

Flamerite Fires Essence Gotham 600 Bedienungsanleitung

Flamerite Fires

Flamerite Fires Valliant Bedienungsanleitung

Flamerite Fires

Flamerite Fires Jaeger Bedienungsanleitung

Flamerite Fires

Flamerite Fires E-FX Geo 1500 Media Wall Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung