Flashforge DREAMER Bedienungsanleitung

This guide only applies to Dreamer 3D printer of Flashforge

Quick Start Guide

Caution

1. Do not peel the yellow film from the build plate. It is heat-resistant tape, which makes objects stick to the build plate easily.

2. Do not remove the wrapping around the nozzle. It consists of ceramic fiber and heat-resistant tape that help to keep the nozzle

at a constant temperature so as to extrude the filament fluently.

3. If print with PLA filament, please remove the lid and open the front door to ventilate for a better printing performance.

Warning 1. High Temperature! Platform may have been heated before; make sure it has cooled down before inner operation.

2. Loose clothes, jewelry and long hair can be caught in moving parts. Please keep away from them.

Dreamer 3D Printer Quick Start Guide Power Cable USB Cable

SD Card

Kit Contents

Parts with are packed in tool box.

This g uide on ly appl ys to Dre amer 3D p rinte r of Flas hforg e 3D Techn ology

Quick Start G uide

Notes

1.Don't strip the yellow film of the heating board, which is high temperature resistant tape, making object stick on platform easily.

2.Don't remove the tape that wrap around the nozzle, which is made from ceramic fibre to stabilize the temperature of the nozzle,

then promote fluency and stability of filament output.

3. If print with PLA filament, please remove the top cover and open the front door to ventilate well for a better printing performance.

Warning 1. High Temperature! Platform may have been heated before, make sure it already cools down before inner operation.

2. Moving parts may cause injury of crushing and scratch, keep your hands naked during operation.

Filament Spool*2 Spool Lock*2 Turbofan Baffle Tool Box

Screw Box Sensor Cable

Tweezer Scraper Graver

Do Not Touch请勿触摸

CAUTION

注意 1.Extruder hot during operation.

使用过程中喷头会发热。

2.Heating plate hot during operation. Allow surface to cool before servicing.

使用过程中加热平台会发热，待平台表面冷却后再操作。

Build Tape Leveling Tool

Getting to Know Your Dreamer

Notes Read all instructions and notes in the Quick Start

Guide and Users Guide before setup and use.

Lid

Extruder Fan

Nozzle

Ventilating Fan

Front Door

Z-Axis Guide Rod

Touch Screen

Filament

Build Plate

X-Axis Guide Rod

Timing Belt

Spring Presser

Turbo Fan

Filament Intake

Side Panel

Reset Button

SD Card Input

USB Input

Power Switch

Power Input

1 2

3 4

5 6

Hardware Assembly

Lay the extruder set on top of extruder seat with two

extruder fans facing the front; align the screw holes

and secure the extruder set onto the extruder seat

by tightening two M3x8 screws from the bottom up

with a Φ2.5mm Allen Wrench.

Take out turbofan baffle, and attach it onto the left

side of the extruder set. Secure it by tightening a

M3x6 screw with 2.5mm Allen Wrench.

Place filament spool onto spool holder with

spool being fed from the bottom towards the back

of the Dreamer. Lock the filament in place by

securing it with the filament spool lock and turning it

counter-clockwise.

Thread the filament through the filament guide tube,

and attach the guide tube onto the two filament

guide tube brackets to avoid filament winding.

Press the spring presser, and insert filament

into filament intake.

Take out the two side panels and install them

onto the two sides of Dreamer body according

to illustrations.

Changing Voltage on Dreamer Power Supply

PRECAUTION

Flashforge Dreamer uses a switching power supply with 115V/230V. Prior to installing the hardware, it is critical to check the AC output

voltage of your home or workplace. The power supply should be switched to reflect your AC output voltage. Failure to do so will cause

severe damage to the Dreamer. Please follow the steps below to switch to the correct voltage. For the United States and Canada, the

correct voltage to use is 115V. For European countries, use 230V. Please double-check as FLASHFORGE will not be responsible for

damages due to improper.

1. The power supply is located at the bottom of the

Dreamer. Gently rest the Dreamer with the front

panelfacing down. Hold the extruder set while

doing this. You will see the power supply switch.

2. Using a hex wrench, switch it to the appropriate

voltage for your country.

230V

AC INPUT VOLTA GE CAN BE

SELECTED BY SWITCH.CHECK

IN PUT VO LTAGE AVOI DING

DAMAGE BEFORE POWER ON.

Leveling the Build Plate

HOME

Filament Level Home Jog Mode

Setting Monitor About

Please adjust the front thumb screw under

Platform when stop.

1The blue build tape has been pasted on the build plate

before leaving factory. (If changing tape is needed,

please heat the build plate up to 110 for easier operation.)

2From the main menu, tap [Tools] and [Level]. The extruder and

build plate will begin to move to the starting position.

3Tap [Next] to start the second position leveling and

repeat the same leveling technique, and then go on

with the other positions to finish this leveling.

Once the extruder and build plate stop moving, slide the leveling

tool (a blue sheet) continuously back and forth between the nozzle

and the build plate. And simultaneously adjust the screw just

enough so that the paper causes a slight friction.(Scan the QR

code on the leveling tool card to watch the instructional video.)

Do Not T

ouch请勿触摸

UTION

注意

1.Extruder hot during operation.

使用过程中喷头会发热。

2.Heating plate hot during operation. Allow surface to cool before servicing.

使用过程中加热平台会发热，待平台表面冷却后再操作。

Turn the nut clockwise

Raise the build plate to reduce

the distance between the plate

and nozzle.

Turn the nut anticlockwise

Lower the build plate to increase

the distance between the plate

and nozzle.

23%

Loading Filament

HOME

Filament Level Home Jog Mode

Setting Monitor About

1 2

Load Left

Load Right

Unload Left

Unload Right

Heating...

L Extruder 55℃ / 230℃

Cancle

Notes Do not pull out the filament with force as it will damage the gears. If the melted filament has cooled down in the extruder, please repeat

the steps of changing filament to load new filament.

Loading Filament

Press down

Changing Filament

1. Cut off the filament.

2. Tap [Tools]--[Filament]--[Load Left / Right] options in sequence to

load the snipped filament into the extruder.

3. When the snipped filament is extruded out of the nozzle, repeat the

last three steps of loading filament to complete operation of changing filament.

1. Remove the lid of the Dreamer; tap the right icon labeled [Tools],

then tap [Filament].

2. Select [Load Left] or [Load Right] as you want.

3. Wait for the extruder to heat up to the operating temperature with an alert.

4. Secure the filament with a flat cross-section and load it by inserting the

filament into the extruder at an upright angle, meanwhile press down the

spring presser.

5. Filament will start to extrude out of the nozzle. Continue loading to

ensure that the filament is extruding in a straight line.

First Print

Adjust the model to the right position in the FlashPrint

software, then click [Print], and a printing options

screen will show up. After the settings are set, click

[OK] to slice and generate Gx file.

Copy this Gx file into SD card and insert SD card. Turn

on the Dreamer. Ensure the build plate is leveled and

load the filament in a right way to ensure the filament

is extruding in a straight line.

Tap [Print] in the main menu of screen, and then tap

[SD Card] to select the .g file you want to print.

Once tap [Print], the Dreamer will start to preheat 5-10

minutes to the operating temperature and then start

the print.

Notes

1. Load the filament for a while to extrude the melted filament out of the extruder that you printed last time.

2. Do not leave the Dreamer unattended during operation.

3. If needed, gently use the scraper to remove the object from build plate to avoid damaging the objects and build plate. If desired,

heat the build plate to 40~50℃to separate the object from the build plate.

4. Please preheat the heating plate to 50-70 degrees Celsius for printing with PLA.

Elephant

Print Time 10:05

Print Copy

Delete

25℃

25℃/220℃

21℃/105℃

Print Time 0 : 00

Elephant

L Extruder

R Extruder

Platform

Andere Handbücher für DREAMER

Inhaltsverzeichnis

Andere Flashforge 3D-Drucker Handbücher

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Creator 3 Pro Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge Hunter Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Guider Bedienungsanleitung

Flashforge

Flashforge CN/EN-A01 Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Guider IIs Bedienungsanleitung

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Creator 3 Bedienungsanleitung

Flashforge

Flashforge Inventor II Bedienungsanleitung

Flashforge

Flashforge AD1 Bedienungsanleitung

Flashforge

Flashforge Guider 2 Bedienungsanleitung

Flashforge

Flashforge Cura Handbuch

Flashforge

Flashforge Invertor II Bedienungsanleitung

Flashforge

Flashforge Creator Pro Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge Creator 3 Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge Adventurer 5M Pro Bedienungsanleitung

Flashforge

Flashforge ADVENTURER 3 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch