Flavel Atlanta FBFR MN Series Bedienungsanleitung

ATLANTA

Model No. FBFR**MN

** denotes fascia variant

RADIANT BALANCED FLUE GAS FIRE

Installation and Maintenance Instructions

Hand these instructions to the user

This appliance is only for use on Natural Gas (G20) at a supply

pressure of 20 mbar in GB / I.E. Before Installation, ensure that the

local distribution conditions and the adjustment of the appliance are

compatible.

Information Requirements for Commission Regulation (EU) 2015/1188

Model Identifier FBFR**MN

Indirect Heating Functionality No

Direct Heat Output 2.4kW

Indirect Heat Output Not Applicable

Fuel Natural Gas (G20)

NOx Emissions 130mg/kWh

Nominal Heat Output 2.4kW

Minimum Heat Output (Indicative) 1.3kW

Useful Efficiency at Nominal Heat Output 66.4%

Useful Efficiency at Minimum Heat Output (Indicative) 50.0%

Auxilliary Power Consumption at Nominal Heat Output Not applicable

Auxilliary Power Consumption at Minimum Output Not applicable

Auxilliary Power Consumption at Standby Mode Not applicable

Permanent Pilot Flame Requirement Not applicable

Type of Heat Output / Room Temperature Control Two or more manual

stages, no room

temperature control

Contact Details BFM Europe Ltd.

Gordon Banks Drive

Trentham Lakes North

Stoke-on-Trent

ST4 4TJ

Tel : 01782 339000

CONTENTS

Section 1 Information and Requirements PAGE

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Fireplace / surround suitability 4

1.3 Flue terminal position 5

1.4 Shelf position 6

1.5 Hearths 6

Section 2 Installation of Fire

2.1 Unpacking the fire 7

2.2 Fire place opening / catchment 7

2.3 Preparation of the wall 9

2.4 Flue installation 10-11

2.5 Gas pipe installation 12

2.6 Securing the firebox to the wall 13-16

2.7 Removing the glass frame 17

2.8 Fitting the flue terminal 18

2.9 Fitting the optional terminal guard 19

2.10 Gas tightness and burner pressure 19-20

2.11 Lighting the appliance 20

Section 3 Maintenance

3.1 Removal of the Piezo Igniter 21

3.2 Removal of the Control valve 21

3.3 Removal of the Pilot Assembly 22

3.4 Removal of the burner 22

Model number FBFR**MN, ** denotes trim / fret variant

Manufactured by: -

BFM Europe Ltd

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

Telephone 01782 339000

Efficiency Declaration

The efficiency of this appliance has been measured as specified in BS EN 613 : 2001 and the

result is 75%. The gross calorific value of the fuel has been used for this efficiency calculation.

The test data from which it has been calculated has been certified by Advantica. The efficiency

value may be used in the UK Government’s Standard Assessment Procedure (SAP) for energy

rating of dwellings.

SECTION 1

INFORMATION AND REQUIREMENTS

1.0 APPLIANCE INFORMATION

Main injector (1 off) Stereomatic Injector Elbow, size 60

Pilot Type S.I.T.140 Series

Max. Gross Heat Input: 4.0 kW

Min. Gross Heat Input: 2.5 kW

Cold Pressure: 20.0+/-1.0 mbar (8.0 +/- 0.4 in w.g.)

Ignition Push-button Piezo

Electrode Spark Gap 4.0mm

Weight (without fender) 26.0 kg inclusive of flue pipe and terminal

Before installation, ensure that the local distribution conditions (identification of the type of gas and

pressure) and the adjustment of the appliance is compatible.

Fig 1.

1.1 CONDITIONS OF INSTALLATION

470mm

150mm

433mm

580mm

50mm

1.1 INSTALLATION CONDITIONS

It is the law that all gas appliances are installed only by a GAS SAFE Registered Installer, in

accordance with these installation instructions and the Gas Safety (Installation and Use)

Regulations 1998 as amended. Failure to install appliances correctly could lead to prosecution. It

is in your own interest and that of safety to comply with the law.

The installation must also be in accordance with all relevant parts of the Local and National

Building Regulations where appropriate, the Building Regulations (Scotland Consolidation) issued

by the Scottish Development Department, and all applicable requirements of the following British

Standard Code of Practice.

1. B.S. 5871 Part 1 Installation of Gas Fires

2. B.S. 6891 Installation of Gas Pipework

3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation

1.2 FIREPLACE / SURROUND SUITABILITY

The fire is suitable for fitting to non-combustible fireplace surrounds and proprietary fireplace

surrounds with a temperature rating of at least 150oc.

If a heating appliance is fitted directly against a wall without the use of a fire surround or

fireplace all combustible material must be removed from behind the trim. Soft wall

coverings such as blown vinyl, wallpaper etc. could be affected by the rising hot air and

scorching and/or discoloration may result. Due consideration should be made to this when

installing or decorating.

1.3 FLUE TERMINAL POSITION

The minimum acceptable dimensions from the flue terminal to obstructions and ventilation

openings are shown below on Table A and (Fig 2).

MINIMUM DIMENSIONS FOR FLUE TERMINAL POSITION

DIMENSI0N

TERMINAL POSITION

MINIMUM DIMENSION

Directly below an opening, air brick,

window etc

300mm

Below gutters, soil pipes or drain pipes

75mm

Below eaves

200mm

Below balconies or car port roof

200mm

From a vertical drain pipe or soil pipe

75mm

From an internal or external corner

300mm

Above ground roof or balcony level

300mm

From a surface facing the terminal

600mm

From a terminal facing the terminal

1200mm

From an opening in the car port

1200mm

Vertically from a terminal on the same wall

1500mm

Horizontally from a terminal on the same

wall

300mm

Fig 2.

1.4 SHELF POSITION

The fire may be fitted below a combustible shelf providing there is a minimum distance of 200mm

above the top of the fire and the shelf does not project more than 150mm. If the shelf overhangs

more than 150mm the distance between the fire and the shelf must be increased by 15mm for

every 25mm of additional overhang over 150mm.

1.5 HEARTHS

This appliance does not require the fitting of a hearth, but we do recommend that a hearth of

minimum width 760mm and minimum projection forwards of 125mm is used. This recommended

hearth can be manufactured from combustible or non-combustible material.

SECTION 2

INSTALLATION OF FIRE

2.1 UNPACKING THE FIRE

Carefully lift the fire out of the carton. Remove the loose item packaging carefully from the front of

the appliance.

IMPORTANT: THE CARDBOARD FITMENT THAT IS AT THE TOP OF THE

CONVECTION APERTURE SHOULD NOT BE REMOVED UNTIL THE

APPLIANCE IS FULLY INSTALLED AND READY TO BE LIT.

DO NOT UNDER ANY CIRCUMSTANCES USE THIS APPLIANCE IF THE GLASS PANEL

IS BROKEN OR NOT SECURELY FIXED TO THE FIREBOX.

Check the contents as listed: -

Packing Check List

1off Fire box / burner assembly

1off Fascia Assembly & Ashpan Cover

1off Flue Terminal unit –pack 2 of 2

1off Loose Items pack –containing :- 1 off Flue pipe gasket

4 off No.12 x 65mm fixing screws

15 off No.8 x 10mm fixing screws

4 off rawplugs

1 off 6mm Allen Key

1off Right Hand Supply Pipe

1off cable fixing kit

1 off heat deflector plate

2.2 FIRE PLACE OPENING

The front opening of the fireplace must be between 410 and 420mm wide, and between 550 and

560mm high. If the opening exceeds these dimensions then a surround must be constructed from

suitable non-combustible material to produce a suitable sized opening. Any surround must be

suitably sealed to the wall or fireplace to prevent leakage. See fig.3

Fig. 3

550min, 560max

410min

420max

480min

Minimum flat

sealing area

620min

Fire opening

A min/max sized opening with a flat rear face between the fire opening and flue outlet

terminal is shown below (fig 4).

Fig. 4

NOTE: WHEN MEASURING LENGTH BETWEEN FIREBOX AND THE OUTER WALL

TAKE INTO ACCOUNT THE DISTANCE BETWEEN THE BACK OF THE BOX AND THE

OUTER WALL AS THIS WILL VARY BETWEEN INSTALLATIONS.

The appliance must be fitted into a fireplace, fire surround or false chimney constructed of

non-combustible materials, minimum width 402mm, minimum rebate 50mm (with optional

black 3” spacer fitted), or 125mm without black spacer fitted.

300mm

125mm

Add any additional space behind

the firebox to the overall wall

thickness when calculating length

of flue pipes required.

760mm

Inner Wall

Outer Wall

402mm

472mm Including Firebox Flanges

Firebox

Front

Flue Outlet

Minimum Cavity

Depth 150mm

Maximum Flue

Length 550mm,

dependent on rebate

available.

Outer Wall

2.3 PREPARATION OF THE WALL

The appliance and flue pipes must be installed at right angles to the mounting wall. The appliance

itself should be installed vertically against a flat wall. Where an uneven wall surface is found,

appropriate action should be taken to ensure that the appliance is not stressed or does not distort

when installed.

Ensure that the floor that the appliance is mounted onto is flat.

The minimum height from the hearth to the centre of the flue is shown on fig. 5 below.

2.4 FLUE INSTALLATION

Fig. 5

2.3.1 Mark the position of the centre of the flue on both the inner and outer walls

2.3.2 Mark the positions of the cable fixing eyes. (See p15 fig.11).

2.3.3 Cut hole for outer flue pipe. There are two possible methods to achieve this, either core drill

or via hammer and chisel.

2.3.4 To core drill, proceed as follows: -

a) Drill a pilot hole through the wall, in position as specified in figure 5.

b) Using a 6” core drill, drill the flue hole. Where possible we recommend that the hole

be drilled from both the inner and outer walls, thus ensuring that the edges of the

holes are clean and concise on both inner and outer faces.

To Hammer and chisel, proceed as follows: -

a) Mark the position of the centre of the flue pipe as specified in figure 5.

b) Mark the position of the hole around this point.

152mm 6”

433mm

Inhaltsverzeichnis

Andere Flavel Kamin im Innenbereich Handbücher

Flavel

Flavel "Waverley" Inset Tray FITC00MN Montageanleitung

Flavel

Flavel Castelle Montageanleitung

Flavel

Flavel Pure FPRG**RN2 Bedienungsanleitung

Flavel

Flavel Caress Slimeline SC FNVC**SN Bedienungsanleitung

Flavel

Flavel FRDC**MN Series Bedienungsanleitung

Flavel

Flavel Decadence HE Series Montageanleitung

Flavel

Flavel Atlanta Bedienungsanleitung

Flavel

Flavel Linear Pebble Bedienungsanleitung

Flavel

Flavel Richmond Plus Bedienungsanleitung

Flavel

Flavel Regent FRGCP0MN Bedienungsanleitung

Flavel

Flavel Caress traditional Montageanleitung

Flavel

Flavel Decadence HE Montageanleitung

Flavel

Flavel Curve Bedienungsanleitung

Flavel

Flavel Enchant FSCP**MN Bedienungsanleitung

Flavel

Flavel Calypso FNCN**SN Series Bedienungsanleitung

Flavel

Flavel FWERN0MN Bedienungsanleitung

Flavel

Flavel REGENT FRLC EN Series Bedienungsanleitung

Flavel

Flavel Raglan KBFC**MN Bedienungsanleitung

Flavel

Flavel Caress Bedienungsanleitung

Flavel

Flavel Misermatic FRCM1G Bedienungsanleitung

Flavel

Flavel Emberglow Classic RC Bedienungsanleitung

Flavel

Flavel Kenilworth Montageanleitung

Flavel

Flavel Curve FCRR Series Bedienungsanleitung

Flavel

Flavel Emberglow Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch