Flavel Sophia Simline BF Montageanleitung

Sophia Slimline

BALANCED FLUE LOG EFFECT GAS FIRE

Installation, Maintenance & User Instructions

Hand these instructions to the user

Model No’s FSBL**RN is only for use on Natural Gas (G20) at a

supply pressure of 20 mbar in G.B. / I.E.

** denotes cosmetic variant

Information Requirements for Commission Regulation (EU) 2015/1188

Model Identifier FSBL**RN

Indirect Heating Functionality No

Direct Heat Output 4.3kW

Indirect Heat Output Not Applicable

Fuel NG (G20)

NOx Emissions 130mg/kWh

Nominal Heat Output 4.3kW

Minimum Heat Output (Indicative) 1.3kW

Useful Efficiency at Nominal Heat Output 87.2%

Useful Efficiency at Minimum Heat Output 50.0%

(Indicative)

Auxilliary electrical power consumption at 0.0000008kW

nominal heat output

Auxilliary electrical power consumption at 0.0000008kW

heat output

Auxilliary electrical power consumption at 0.0000008kW

standby mode

Permanent pilot flame requirement 0.213kW

Type of heat output / room temperature With electronic room temperature

control plus day timer.

Contact Details BFM Europe Ltd.

Gordon Banks Drive

Trentham Lakes North

Stoke-on-Trent

ST4 4TJ

Tel : 01782 339000

CONTENTS

PAGE

Section 1 Information and Requirements

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Fireplace surround & suitability 4

1.3 Flue Terminal Position 5

1.4 Shelf position 6

1.5 Hearths 6

Section 2 Installation of Fire

2.1 Unpacking the fire 6

2.2 Fireplace opening 7-8

2.3 Preparation of the wall 8-9

2.4 Preparation of the flue hole 9

2.5 Installation of the gas supply 10

2.6 Preparation of the flue duct 11

2.7 Securing the firebox to the opening 12-13

2.8 Installing the “Sophia” surround 14-15

2.9 Making the gas connection / pressure testing 16

2.10 Fitting the batteries 16

2.11 Removal & refitting of the glass frame 17-19

2.12 Fitting the terminal guard 19

2.13 Removal & refitting of the burner assembly 20-21

Section 3 Assembling Fuel Bed and Commissioning

3.1 Fitting the log fuel bed 22-26

3.2 Lighting the appliance 27-30

3.3 Fitting the handset wall bracket 31

3.4 Instructing the user / product handover 31

Section 4 Maintenance

4.1 Removal of the burner assembly 32

4.2 Removal of the gas valve 32

4.3 Removal of the pilot assembly 33

4.4 Replacement of handset batteries 33

4.5 Replacement of the batteries in the fire 33

4.6 Removal of the control board / receiver unit 33

4.7 Parts shortlist 34

Section 5 User Instructions

5.1 Conditions of Installation 42

5.2 About your new fire 43

5.3 Operating the fire 44-49

5.4 Removal / re-fitting the glass frame assembly 50-52

5.5 Removal / replacement of the fuel-bed 53-56

5.6 Cleaning the fire 57-58

5.7 User replaceable parts 58

5.8 Removing / replacing the batteries 58

This appliance is manufactured by :-

BFM Europe Ltd, Trentham Lakes,

Stoke-on-Trent, ST4 4TJ.

SECTION 1

INFORMATION AND REQUIREMENTS

1.0 APPLIANCE INFORMATION

Model FSBL**RN

** denotes cosmetic variant of product

Gas Type G20

Main injector (1 off) Size 1.70mm

Pilot Type Black Technigas “Polidoro” G27.2

Max. Gross Heat Input : 5.5 kW

Min. Gross Heat Input : 2.5 kW

Gas Rate : 0.511 m3/hr

Cold Pressure : 20.0 +/-1.0 mbar

Electrode Spark Gap 4.0mm

Packed Weight 80.5kg

Gas Connection : 8mm Compression (supplied with fire)

Fig. 1

INSTALLATION REQUIREMENTS

Efficiency Declaration

The efficiency of this appliance has been measured as specified in

BS EN 613 : 2001 and the result after conversion to Gross using the

appropriate factor from Table 4 of SAP 2009 is 78%. The test data from which it

has been calculated has been certified by BSI. The efficiency value may be used

in the U Government’s Standard Assessment Procedure (SAP) for energy rating

of dwellings.

1.1 CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a GAS SAFE Registered

Installer, in accordance with these installation instructions and the Gas Safety

(Installation and Use) Regulations 1998 as amended. Failure to install appliances

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building Regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

applicable requirements of the following British Standard Code of Practice.

1. B.S. 5871 Part 1 Installation of Gas Fires

2. B.S. 6891 Installation of Gas Pipework

3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. I.S 813 : 1996 Domestic Gas Installation, issued by the National Standards

Authority of Ireland.

1.2 FIREPLACE / SURROUND SUITABILITY

The fire must only be installed with the surround supplied it must not be installed

directly onto carpet or other combustible floor materials.

If a heating appliance is fitted directly against a wall combustible material must be

removed from behind it. Soft wall coverings such as blown vinyl, wall paper etc.

could be affected by the rising hot air and scorching and/or discoloration may

result. Due consideration should be made to this when installing or decorating.

This product can only be installed with the surround design supplied by the

manufacturer or designs which meet the criteria as required by BFM Europe.

For further details of specification requirements please contact BFM Europe

Technical Service.

1.3 FLUE TERMINAL POSITION

The minimum acceptable dimensions from the flue terminal to obstructions

and ventilation openings are shown below and listed in the table

It is important that the position of the flue allows the free passage of air

across it at all times. The minimum acceptable space from the flue terminal

to obstructions and ventilation openings are specified below (figure 2).

Fig. 2

DIMENSION TERMINAL POSITION MINIMUM DIMENSION

A Directly below an opening, air brick, 300mm (12in)

opening window

B Above an opening, air brick, 300mm (12in)

opening window

C Horizontally to an opening, air brick, 300mm (12in)

opening window etc.

D Below gutters, soil pipes or drain pipes 300mm (12in)

E Below eaves 300mm (12in)

F Below balconies or car port roof 600mm (12in)

G From a vertical drain pipe or soil pipe 300mm (12in)

H From an internal or external corner 600mm (24in)

I Above ground roof or balcony level 300mm (12in)

J From a surface facing the terminal 600mm (24in)

From a terminal facing the terminal 600mm (24in)

L From an opening in the car port 1200m (48in)

M Vertically from a terminal on the same wall 1500mm(59in)

N Horizontally from a terminal on the 300mm (12in)

same Wall

O NOT APPLICABLE N/A

P NOT APPLICABLE N/A

Q NOT APPLICABLE N/A

1.4 SHELF POSITION

This fire must not be fitted below combustible shelf materials.

1.5 HEARTHS

This appliance must only be installed with the Flavel Sophia Slimline hearth panel

or an alternative item as dimensionally approved by BFM Europe.

SECTION 2

INSTALLATION OF FIRE

2.1 UNPAC ING THE FIRE

Carefully lift the fire out of the carton. Remove the loose item packaging carefully

from the front of the appliance. Check the contents as listed :-

Packing Check List - All Models

Pack 1 of 2 - Combustion Chamber Pack

1 off Combustion chamber & glass frame assembly

1 off Boxed ceramic fuel-bed set (packed inside combustion chamber)

1 off Wall plate

1 off Flue terminal / pipe unit

1 off Flue terminal guard (packed inside combustion chamber)

1 off Installation / user book (combined)

1 off Guarantee card

1 off Front grill (painted)

1 off Loose items pack – containing :- 1 off standard fixing kit

1 off 9V PP3 battery

4 off AA batteries

1 off thermostatic remote handset

wall bracket and fixings

4 off 8mm rawlpugs & fixing screws

1 off length of foil tape 500mm

4 off 8mm nylon plugs

4 off 30mm wood screws

2 off surround securing brackets

Pack 2 of 2 - Sophia Surround 1 off glass removal tool

1 off Hearth 1 off L/H leg

1 off Shelf 1 off R/H leg

1 off Top infill 1 off Shelf infill section

1 off Firebox / burner assembly 2 off Side infill sections

1 off Bottom infill section 2 off shelf brackets

2 off Shelf infill brackets 2 off Leg brackets

2.2 FIRE PLACE OPENING

2.2.1 The front opening of the fire place must be between 750 and 840mm

wide and between 1025mm and 1050mm high. If the opening exceeds

these dimensions then a surround must be constructed from suitable

non-combustible material to produce a suitable sized opening. Any

surround must be suitably sealed to the fire place to prevent leakage.

See figure 3 below.

Fig. 3

2.2.2 The minimum / maximum sized distances between the firebox mounting

flange and outside wall are shown below and overpage in figure 4 & 5.

Fig. 4

750mm minimum,

840mm maximum

Fire Opening

1025mm minimum,

1050mm maximum

Minimum Flat

Sealing Area

10mm

Minimum Installation

Depth 254mm

Maximum Installation Depth

554mm

Level of bottom of

hearth panel /

firebox

Fig. 5

2.3 PREPARATION OF THE WALL

2.3.1 The appliance and flue pipes must be installed at right angles to the

mounting wall. The appliance itself should be installed vertically against

a flat wall. Where an uneven wall surface is found, appropriate action

should be taken to ensure that the appliance is not stressed or does not

distort when installed.

2.3.2 Ensure that the floor surface onto which the appliance is mounted onto

is flat. The minimum height from the floor to the centre of the flue is

shown on figure 6 overpage.

746mm 154mm

Outer Wall

938mm Including

Firebox Flanges

300mm

Cavity

Flue Terminal

Fig. 6

2.4 PREPARATION OF THE FLUE HOLE

2.4.1 Mark the position of the centre of the flue on the inner wall.

2.4.2 Cut hole for outer flue pipe. There are two possible methods to achieve

this, either core drill or via hammer and chisel.

2.4.3 To core drill, proceed as follows :-

Drill a pilot hole through the wall, in position as specified in figure 6.

Using a 6” core drill, drill the flue hole.

To Hammer and chisel, proceed as follows :-

Mark the position of the centre of the flue pipe as specified in figure 6.

Mark the position of the hole around this point.

Chisel out the area as marked on the wall.

2.4.4 We then recommend that a cardboard cylinder is placed around the flue

pipe and inserted in the chiselled out hole whilst making good.

NOTE :- If the appliance is to be installed into a building under

construction, it is recommended that a non-corrosive metal

tube of 6” diameter be inserted into the position of the hole.

150mm diameter

870mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Flavel Kamin im Innenbereich Handbücher

Flavel

Flavel Enchant FSCP**MN Bedienungsanleitung

Flavel

Flavel Pure FPRG**RN2 Bedienungsanleitung

Flavel

Flavel Linear Pebble Bedienungsanleitung

Flavel

Flavel Ora Bedienungsanleitung

Flavel

Flavel Emberglow Classic FEMC00MN Bedienungsanleitung

Flavel

Flavel Caress traditional Montageanleitung

Flavel

Flavel Kamina Bedienungsanleitung

Flavel

Flavel Onyx MK2 FFHOW0RE2 Bedienungsanleitung

Flavel

Flavel Warwick FIRC**MN Bedienungsanleitung

Flavel

Flavel FKPC MN Series Montageanleitung

Flavel

Flavel Emberglow FEBC00MN Bedienungsanleitung

Flavel

Flavel FWERN0MN Bedienungsanleitung

Flavel

Flavel Atlanta FAVRU0MN Bedienungsanleitung

Flavel

Flavel Calypso Montageanleitung

Flavel

Flavel Decadence HE Series Montageanleitung

Flavel

Flavel "Waverley" Inset Tray FITC00MN Montageanleitung

Flavel

Flavel Decadence HE Montageanleitung

Flavel

Flavel Calypso FNCN**SN Series Bedienungsanleitung

Flavel

Flavel Windsor Montageanleitung

Flavel

Flavel Emberglow Bedienungsanleitung

Flavel

Flavel Caress HE Montageanleitung

Flavel

Flavel Linear Montageanleitung

Flavel

Flavel Vesta Montageanleitung

Flavel

Flavel Atlanta Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung