FLIR Ariel CM-3202-11-I Bedienungsanleitung

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain anyexport-controlled information.

Ariel™ Mini-Dome

CM-3202-11-I

Quick Install Guide

1. Check Contents

Make sure all of the items above are included in the camera kit.

2. Prepare to Install the Camera

2.1 Install FLIR DiscoveryNetwork Assistant

Download the FLIR Discovery Network Assistant (DNA) tool to a computer on the

same VLAN to which you will connect the camera, and then unzip the file. The DNA

tool does not require a license to use and is a free download from FLIR.com >

Products > Security > Visible Security Cameras > FLIR ARIEL™ CM-3202.

2.2 Perform a Bench Test (Optional)

You can test the camera or configure it for networking before mounting it. Remove

the camera cover (see 3.2 Remove Camera Cover), connect the camera (4.3 Route

Cables and Connect the Camera), and attach the camera cover (4.3 Attach

Camera Cover). Then, you can perform a bench test or discover the camera and

configure it for networking (4.1 Configure for Networking) before continuing with

2.3 Select a Location.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

2.3 Select a Location

Select a suitable location to mount the camera.

For advice on positioning and orienting the camera, see the camera's installation

and user guide.

Verify that the operating temperature range is between -30°C ~ 60°C (-22° ~ 140°

F), 10-90% relative humidity (non-condensing).

For the list of mounting accessories available for the camera, see the FLIR

Security Cameras - Accessory Guide.

3. Install the Camera

3.1 Fit Mounting Hardware

If required, install the mounting hardware for the camera according to the

instructions for the hardware.

3.2 Remove Camera Cover

a. Using the Torx wrench, loosen the three Torx

screws counter-clockwise (1).

b. Gently pull the top cover away from the

camera body (2).

Internal Interfaces

Internal interface

Description

DEFAULT

To reset the camera to its factory defaults, press the Default

button for six seconds.

RESET

To reboot the camera, press the Reset button for one second.

Micro SD card slot

For recording and file storage, insert a microSDXC card (up to

256 GB, Class 10) in the card slot.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

Internal interface

Description

RS232 terminal block

Not used

3.3 Route Cables and Connect the Camera

System Cable

Connector

Black

RJ-45

Pink

AUDIO OUT

Light green

AUDIO GND

Light blue

MIC IN-

Yellow black

MIC IN+

Purple

ALARM COM

Blue

ALARM OUT

Gray

ALARM IN

White

ALARM GND

Black

12 VDC-

Red

12 VDC+

a. Properly install the power and network cabling in the mounting hardware so that

it is accessible when the camera is mounted.

b. Attach an Ethernet cable from the network switch to the RJ45 connector for a

100 Mbps Ethernet and PoE (Power over Ethernet) IEEE 802.3af Class 3

connection. Ethernet is required for streaming video and for configuring the

camera.

c. Connect the audio, microphone, and alarm connectors, as needed.

d. If using a 12 VDC power supply, connect its wires to the two-pin power terminal

block.

Cables can enter the

camera from the side or

from the bottom.

Side cable entry

Bottom cable entry

3.4 Mount the Camera

a. Be sure to have the required accessories and tools available.

b. Refer to the camera's installation and user guide as necessary.

c. Paste the included drill template onto the wall or ceiling where you are mounting

the camera.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

d. Drill three anchor holes according to

the template.

e. Hammer the three plastic anchors into

the drilled holes.

f. If the cable from the conduit does not

enter on the side of the camera, drill a

hole for cable entry according to the

template.

g. Place the camera over the

surface and securely fasten

the three tapping screws

clockwise into the plastic

anchors.

h. Check that the camera's

orientation covers the

required field of view.

3.5 Place the Desiccant in the Camera

a. Carefully tear open the vacuum-packed

aluminum desiccant bag along the slit on one

edge.

b. Remove the desiccant.

c. Remove the paper backing of the double-sided

tape on one side of the desiccant.

d. Firmly attach the desiccant to the camera in the

location shown.

Important

After placing the desiccant in the camera, attach the

camera cover as soon as possible.

To prevent condensation in the camera, tightly seal the

mounts and conduits. Otherwise, the desiccant will become

damp and cannot be used.

4. Configure the Camera

You can configure the camera using the DNA tool, the camera's web page, or a

VMS.

DNAtool

Camera's web page

Discover camera IP address

•

Configure IP address, mask, and gateway

•

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

DNAtool

Camera's web page

Configure DNS settings, MTU, and Ethernet speed

•

Change user credentials

•

Change video format

•

Configure more than one camera at the same time

•

For information about using a VMS to configure the camera, see the VMS

documentation.

4.1 Configure for Networking

By default, DHCP is enabled on the camera and a DHCP server on the network

assigns the camera an IP address. For example, if the camera is managed by

FLIR's Horizon or Meridian VMS and the VMS is configured as a DHCP server, the

VMS automatically assigns the camera an IP address.

If the camera is managed by FLIR’s Latitude VMS or is on a network with static IP

addressing, you can manually specify the camera’s IP address using the DNA tool

or the camera's web page. The camera's default IP address is 192.168.0.250.

To manually specify the camera's IP address using the DNA tool:

a. Make sure the camera and the PC are on the same LAN segment.

b. Run the DNA tool (DNA.exe) by double-clicking .

The Discover List

appears, showing

compatible

devices on the

LAN segment and

their current IP

addresses.

In the DNA Discover List, verify that the camera's status is Online.

If this is the first time you are configuring the camera or if it is the first time after

resetting the camera to its factory defaults, DNA automatically authenticates the

camera with the default password for the camera's admin user (admin).

If the admin user password has been

changed, you need to authenticate the

camera.

In the DNA Discover List, right-click the

camera and select Login.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

In the DNA - Login window, type the

password for the admin user. If you do

not know the admin user password,

contact the person who configured the

camera's users and passwords.

Click Login, wait for Ok status to

appear, and then click Close.

In the DNA Discover List, verify that the camera's status is Authenticated.

d. Change the camera’s IP address.

Right-click the camera and select IP

Setup.

In the DNA - IP Setup window, clear

Use DHCP and specify the camera's IP

address. You can also specify the Mask

(default: 255.255.255.0) and Gateway.

Then, click Update, wait for Ok status

to appear, and then click Close.

4.2 Change Video Format (Optional)

By default, NTSC is the camera's video

format.

To change the camera's video format to

PAL using the DNA tool:

a. In the DNA Discover List, right-click the

camera and select Change Video

Format.

b. In the Change Video Format window,

select PAL.

c. Click Update, wait for Ok status to appear, and then click Close.

For more information about using the DNA tool to configure one or more cameras,

see the DNA User Guide. While the software is open, click the Help icon .

4.3 Complete Camera Setup

Specify the camera's zoom and focus, and format the

microSDXC card, using the camera's web page, which

supports Google Chrome (recommended), Firefox, Microsoft

Edge, and Internet Explorer 11 (32-bit), on PCs running 64-

bit Windows 7, 8, 8.1, or 10.

a. Log in to the camera’s web page.

In the DNA Discover List, double-click the camera.

On the login screen, type a user name and password.

Both are case-sensitive.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

When logging in to the camera's web page for the first time or for the first time

after resetting the camera to its factory defaults, type admin for the user name

and for the password.

Then, specify a new password for the admin user. Use a strong password

consisting of at least eight characters and at least one uppercase letter, one

lowercase letter, and one number. Passwords can include the following special

characters: |@#~!$&<>+_-.,*?= .

Log back in using the new password.

The camera's View Settings Home Page opens.

b. Using the controls under the live video, configure the camera's focus and zoom.

c. Format the microSDXC card.

Click System Settings.

In the top navigation bar, click SD

Card.

Under SD Format, click Format.

CM-3202-11-I QIG Rev 100

June 2020

This document does not contain any export-controlled information.

4.4 Attach Camera Cover

a. Carefully place the top cover onto the

camera body (1).

b. Fasten the three Torx screws

clockwise to complete the mounting

(2).

4.5 Attach the Camera to a VMS

After you have mounted the camera and discovered or defined its IP address, you

can use VMS Discovery/Attach procedures to attach the camera to a VMS.

5. Camera Dimensions

The Ariel CM-3202-11-I camera’s dimensions are:

Side Dimensions

Base Dimensions

6. Register the Product

For warranty information, see https://www.flir.com/support-

center/warranty/security/flir-security-product-warranties/.

7. Contact Information

FLIR Systems, Inc.

6769 Hollister Avenue

Goleta, CA 93117

USA

Support: https://www.flir.com/support/

product.enterprise.support@flir.com

Corporate Headquarters

27700 SW Parkway Ave.

Wilsonville, OR 97070

USA

Andere Handbücher für Ariel CM-3202-11-I

Inhaltsverzeichnis

Andere FLIR Digitalkamera Handbücher

FLIR

FLIR USB3 Vision GRASSHOPPER 3 Bedienungsanleitung

FLIR

FLIR LADYBUG 5 USB3 Bedienungsanleitung

FLIR

FLIR Elara FR-345-EST Bedienungsanleitung

FLIR

FLIR Exx series Bedienungsanleitung

FLIR

FLIR GF300 Bedienungsanleitung

FLIR

FLIR HS-324 Bedienungsanleitung

FLIR

FLIR M500 Bedienungsanleitung

FLIR

FLIR Flir MPX Bedienungsanleitung

FLIR

FLIR Scout Bi-Ocular Bedienungsanleitung

FLIR

FLIR Photon Block 2 Bedienungsanleitung

FLIR

FLIR Quasar CP-6408-31-I Bedienungsanleitung

FLIR

FLIR CP-4221-300 Bedienungsanleitung

FLIR

FLIR Elara FR-345-EST Bedienungsanleitung

FLIR

FLIR ZENMUSE XT2 Bedienungsanleitung

FLIR

FLIR Scout Bedienungsanleitung

FLIR

FLIR BLACKFLY S GIGE Bedienungsanleitung

FLIR

FLIR Tau Camera TAU-0035-00-10 Bedienungsanleitung

FLIR

FLIR PTZ-35 MS Bedienungsanleitung

FLIR

FLIR Alpha Nir Bedienungsanleitung

FLIR

FLIR A3 PT series Bedienungsanleitung

FLIR

FLIR Tau Bedienungsanleitung

FLIR

FLIR BLACKFLY USB3 Vision Bedienungsanleitung

FLIR

FLIR A400 Series Bedienungsanleitung

FLIR

FLIR C237BD Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung