FLIR DM284 Bedienungsanleitung

QUICK START GUIDE

IGMTM MODE ONLY

FLIR MODEL DM284

THERMAL IMAGING IGMTM MODE QUICK GUIDE

FLIR DM284 –IGMTM QUICK START GUIDE Document Identifier: DM284-QS_IGM-en-US_AC

QUICK START GUIDE –EN

IGMTM MODE ONLY

USER MANUAL LOCATION: The detailed User Manual is located on the support.flir.com web site (download

tab). Translations of User Manuals and Quick Starts are also available at the web site. The Quick Start Guide

for the Multimeter functions is a separate booklet located in the product packaging. Please read the entire

User Manual to gain a thorough understanding of the meter before use. Please Register for Extended

Warranty and Product Updates at www.flir.com/testwarranty

METER DESCRIPTION (FRONT)

1. Work Light and NCV detector area

2. LCD Display

3. Navigation/OK buttons

4. MODE Button

5. RANGE Button

6. Work light Button

7. Rotary Function Switch

8. Positive (+) Probe Input Jack for A(Current).

9. Positive (+) Probe Input Jack for mA (Current).

10. COM (-) Probe Input Jack

11. Positive (+) Probe Input Jack for all inputs except Aand mA

12. Display ‘Hold’ (H) button

13. Cancel/Return Button

14. IGMTM Button

METER DESCRIPTION (BACK)

1. Test Lead holder attachment mounts

2. Thermal Imaging lens

3. Laser pointer lens

4. Lens cover slide control

5. Tripod mount (test lead holder attaches here also)

6. Tilt Stand and Battery compartment

QUICK STEPS

To power the meter, move the rotary switch to any position.

Move the lens protector (back of meter) to the open position (up).

Short press the IGM button to open the thermal imager.

Point the meter lens toward the area under test.

Use the cross hairs and laser pointer to select a target.

View thermal image and temperature of the targeted spot.

FLIR DM284 –IGMTM QUICK START GUIDE Document Identifier: DM284-QS_IGM-en-US_AC

METER POWER

Set the function switch to any position to switch the meter ON. If LO BATT is displayed, if one of the Low

Battery screens appear (below), if the battery icon appears low , or if the meter does not power on,

replace the four (4) 1.5V ‘AAA’ batteries in the rear compartment. The optional TA04 Rechargeable Li-

Polymer Battery system is available if battery recharging, rather than replacement, is preferred.

The meter enters sleep mode after 10 minutes (default). The time can be set to 1, 2, 5 or 10 minutes (or

OFF) in the Multimeter Settings menu . 20 seconds prior to entering APO mode, the meter beeps; at this

point, press any button or turn the Rotary Switch to reset the APO timer.

DISPLAY DESCRIPTION

1. Temperature Measurement of the spot sensed. Dashes are displayed while the temperature reading is

stabilizing.

2. The currently selected Emissivity (Ԑ). Use the Thermal

Settings Menu to change the emissivity setting.

3. Status Bar Icon area.

4. Highest reading measured in the current frame.

5. Thermal scale shows the range of colors for thermal

images. The lighter the color, the warmer the temperature;

the darker the color, the cooler the temperature.

6. Lowest reading measured in the current frame.

7. Menu Bar area.

8. Cross hairs for targeting.

9. Thermal image frame

10. DMM measurement is shown below the temperature measurement. Choose to have DMM readings and

icons superimposed on the image using the Image Mode menu .

DISTANCE-TO-SPOT RATIO and FIELD OF VIEW

The Distance-to-Spot (D:S) ratio for the imager is 30:1 meaning that the measurement spot is always 30 times

smaller than the meter-to-spot distance (see D:S ratio diagram below). The thermal imager’s Field of View

(FOV) is 50o(see top view) by 38.6o(see side view).

FLIR DM284 –IGMTM QUICK START GUIDE Document Identifier: DM284-QS_IGM-en-US_AC

Distance-to-Spot ratio 30:1

Field of View (FOV) –Side view Field of View (FOV) - Top view

THERMAL SETTINGS MENU

Press OK to open the main menu. Press OK again on the icon .

IGM Color Palette selection. Press OK to select one of the display color

palettes (Iron, Rainbow, or Gray).

ԐEmissivity: Press OK. Use the arrow pad to scroll to the desired preset

(0.95, 0.85, 0.75, 0.65) and press OK. See diagram. To fine tune, press OK

at the fine-tuning icon (bottom of list) and then use the arrow pad to make

a selection. The available range is 0.10 to 0.99 in 0.01 steps.

Laser pointer: Press OK at this icon to switch the laser pointer ON

(blue dot next to icon) or OFF.

Cross hairs: Press OK at this icon to switch the cross hairs ON or OFF.

FLIR DM284 –IGMTM QUICK START GUIDE Document Identifier: DM284-QS_IGM-en-US_AC

Temperature Differential: Type-K Thermocouple temperature minus IGMTM temperature. Only

available when Image + DMM is selected in the Image Mode Menu (next section) and mV/Temp is

selected with the rotary switch. Press OK to switch this mode ON or OFF.

In the diagram, the arrow points to the differential temperature

(5.0oF). The IGMTM temperature is 85.0oF (top left) next to the

emissivity setting. The Type-K temperature is 80.0oF (2nd row).

For Type-K measurement instructions refer to the Multimeter

‘Getting Started’ guide or the complete DM284 User Manual

available at the support.flir.com web site.

Tip: To find the emissivity of any target spot, measure the spot

with the Type-K probe and the thermal imager and then adjust

the emissivity until the differential temperature is zero.

Type-K / IGMTM Temperature

Differential Reading Example

NOTE: To change the temperature units (oC/oF) use the Multimeter Settings mode. Press OK at this icon .

IMAGE MODE MENU

Press OK to open the Main menu and then press OK on the Image Mode icon. Select Image + DMM

mode or Image Only mode from the Image Mode menu using the arrow buttons.

●Image + DMM (default mode): Display will show all IR data and DMM data.

●Image Only: Display will show IR data only.

●For both options, the status bar will show Battery, APO, Work Light, and Laser icons when applicable.

STATUS BAR DISPLAY ICONS

The Status Bar is located at the top-right display corner. There are 2 rows of icons as

shown below. The icons are always on the right side of the display and in the same

sequence. From top left to right these Status Bar icons are:

Auto Hold

Display Hold

Auto Range

Laser Pointer

Work light

APO (Auto Power OFF)

Battery status

VFD Low Pass Filter icon

FLEX Clamp input range

Low Impedance mode

USE OF THE MULTIMETER IN IGMTM MODE

The Multimeter can be used normally while the IGMTM mode is active with few restrictions. Multimeter

readings, menus, status bar icons, and modes such as PEAK, RELATIVE, and MIN-MAX-AVG can be viewed

directly on top of the thermal image when IMAGE + DMM mode is selected in the Image Mode menu.

FLIR DM284 –IGMTM QUICK START GUIDE Document Identifier: DM284-QS_IGM-en-US_AC

Corporate Headquarters

FLIR Systems, Inc.

2770 SW Parkway Avenue

Wilsonville, OR 97070 USA

Telephone: +1 503-498-3547

Customer Support

Technical Support Website http://support.flir.com

Technical Support Email [email protected]

Service and Repair Email [email protected]

Customer Support Telephone +1 855-499-3662 option 3 (toll free)

Certificate of Conformity and ISO-9001 Quality Management System

FLIR Commercial Systems, Inc., an ISO 9001 certified company, hereby certify that our instruments meet or exceed the

specifications stated in the user manuals.

This instrument was produced under the stringent guidelines of FLIR Commercial System’s certified ISO 9001 Quality

Management System from design to delivery. All instruments are calibrated and inspected to meet the stated

specifications.

FLIR Commercial Systems, Inc. inspects its incoming shipments using an approved sampling plan with an Acceptable

Quality Level (AQL). All incoming inspections are performed using test equipment that is traceable to National

Standards. Our ISO 9001 Quality Management System extends to aftermarket support where tested quality procedures

are applied to customer support, service, calibration and repair processes.

This instrument will provide years of reliable service when used in accordance with the instructions provided in the User

Manual. To have this device certified please contact your local service center.

Quality Assurance Management

Publication Identification No.: DM284-QS_IGM

Release version: AC

Release Date: 2017 January

Language: en-US

Translations of User Manuals and Quick Starts are available at the support.flir.com web site (download tab).

www.flir.com

Andere Handbücher für DM284

Inhaltsverzeichnis

Andere FLIR Multimeter Handbücher

FLIR

FLIR DM284 Bedienungsanleitung

FLIR

FLIR DM286 Bedienungsanleitung

FLIR

FLIR Extech Instruments MG302 Bedienungsanleitung

FLIR

FLIR IM75-2 Bedienungsanleitung

FLIR

FLIR Extech Instruments 410 Bedienungsanleitung

FLIR

FLIR DM284 Bedienungsanleitung

FLIR

FLIR IM75-2 Bedienungsanleitung

FLIR

FLIR DM91 Bedienungsanleitung

FLIR

FLIR DM6 Series Bedienungsanleitung

FLIR

FLIR Extech Instruments MultiMaster MM560A Bedienungsanleitung

FLIR

FLIR DM90 Bedienungsanleitung

FLIR

FLIR Extech Instruments MN15 Bedienungsanleitung

FLIR

FLIR Extech Instruments 380941 Bedienungsanleitung

FLIR

FLIR MR160 Bedienungsanleitung

FLIR

FLIR CM83 Bedienungsanleitung

FLIR

FLIR Extech EX510 Bedienungsanleitung

FLIR

FLIR EXTECH INSTRUMENTS DM110 Bedienungsanleitung

FLIR

FLIR DM90 Bedienungsanleitung

FLIR

FLIR DM285 Bedienungsanleitung

FLIR

FLIR EXTECH INSTRUMENTS EX520 Bedienungsanleitung

FLIR

FLIR DM93 Bedienungsanleitung

FLIR

FLIR DM93 Bedienungsanleitung

FLIR

FLIR DM90 Bedienungsanleitung

FLIR

FLIR DM92 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung