FLIR Quasar CP-6408 Bedienungsanleitung

Quasar CP-6408

4K IR PTZ

Quick Install Guide

Accessing full camera documentation from the Web:

Doc Ver: 2b

CP-6408-21-I QIG

August 2019

Getting Started

CP-6408-21-I QIG

Page

1.Getting Started

1.1 Check Contents

1. CP-6408 4K IR PTZ

2. Pendant Cap

3. M4 Security Screw with Rubber Washer

4. 2-Pin Power Terminal Block (DC 12v use)

5. 3-Pin Power Terminal Block (AC 24V use)

6. 14-Pin Alarm/Audio I/O Terminal Block

7. Quick Install Guide (this document)

1.2 Download Documentation and Software

Use the QR Code on the front page or navigate directly to the FLIR Camera

Catalog, select the Quasar CP-6408 4K IR PTZ, and download the full support

documentation, Installation Guide and utility software (DNA).

Note: The minimum version of DNA required to support this camera is 2.3.0.8

2.Preparation

2.1 Load Host or Workstation Software

Install DNA

Download Documentation and Software as shown, and install the DNA Utility to a

Host or Workstation that is on the network to which the camera will be connected.

2.2 General Preparation

CAUTION:

This product contains a battery that is soldered to the PCB. There is a risk of explosion

if the battery is replaced by an incorrect type.

Do not replace the battery.

The battery should be disposed of in accordance with manufacturer’s instructions.

2.2.1 Bench Setup (Optional)

If you wish to do preliminary setup before Installation, please consult the camera's

User Guide for setting IP Address and Video Format.

Preparation

CP-6408-21-I QIG

Page

2.2.2 Location

Consult the CP-6408 4K IR PTZ User Guide for advice on positioning, orienting and

mounting the camera.

Verify that the operating temperature range is between -40°C ~ 50°C (-40° ~ 122°

F), 10-90% relative humidity (non-condensing).

Refer to the Installation Guide for available mounting accessories. (see Download

Documentation and Software)

Warning!

Before drilling into surfaces, verify that no electrical or other

utility service lines are present. Serious injury or death may

result from failure to heed this warning.

Power: Universal Power Over Ethernet (UPOE), 12 Vdc, or 24 Vac.

Ethernet: Cat5e or Cat6 cable. Ethernet is required for streaming video, and

configuring the camera.

3.Install Camera

3.1 Fit Mounting Hardware

If required, install the mounting hardware for the camera. The Installation Guide

document (see Download Resources List) provides a list of Mounting Accessories

with relevant Mounting Instructions.

3.2 Route Network and Power

Properly install the power and network cabling in the mounting hardware so that it

is accessible when the camera is mounted.

3.3 Mount Camera

Mount the camera. If using mounting accessories, follow all recommended

Mounting Instructions in the Installation Guide (see Download Resources List).

Install Camera

CP-6408-21-I QIG

Page

3.4 Connect the Camera

Connectors

Connector

Connection

DC12V IN

If using a 12Vdc pow er supply, connect its w ires to the two-

pin pow er connector.

UPOE

Attach a Cat 5e or Cat 6 cable fromthe netw ork sw itch to the

RJ45 connector for a 10/100/1000 Mbps Ethernet and UPOE

connection. If using UPOE, FLIR recommends using a FLIR CP-

POE-60W-XX or equivalent pow er injector. Verify that the

UPOEconnector LEDs are steady green and flashing yellow .

AC24V IN

If using a 24Vac pow er supply or a heater, connect its w ires

to the three-pin pow er connector.

DEFAULT

To reset factory defaults at any time, press the Default button

for at least 20 seconds.

14-pin

terminal

block

Attach w ires fromexternal devices to the 14-pin terminal block

connector for alarm and audio in/out (see diagramand

definitions below ).

Analog

Out

Analog Out is not supported on this model

Install Camera

CP-6408-21-I QIG

Page

14-Pin Term inal Block

Definition

Audio-Out

Not used

Ground (Audio I/O)

Alarm-In 4

Alarm-Out A1

Alarm-In 3

Alarm-Out A2

Alarm-In 2

Alarm-Out B1

Alarm-In 1

Alarm-Out B2

Ground (Alarm I/O)

Not used

Audio-In

4.Configuration Steps

The camera’s web interface can be accessed by browsers such as Explorer,

Chrome, Firefox, etc.

Configure for Networking

By default, DHCP is enabled on the camera and a DHCP server on the

network assigns the camera an IP address. If there is no DHCP server on

the network, the IP address defaults to 192.168.0.250.

To manually specify a different IP address for the camera or to configure

other networking settings, you can use either the FLIR Discovery Network

Assistant (DNA) tool or the camera's web page.

Note

For more information about using the DNA tool, including

how to configure more than one camera at the same

time, see the DNA User Guide. While the software is

open, click the Help icon .

Make sure the camera and the PC are on the same network.

To configure the camera for networking using the DNA tool:

a. Run DNA . The Discover List appears, showing cameras on the

network and their current IP addresses.

Configuration Steps

CP-6408-21-I QIG

Page

b. To Authenticate the camera:

i. Right-click the camera and select Login, or click the Login icon

in the navigation bar.

ii. In the DNA - Login window, type the password for the admin user

(default: admin). Then, click Login.

iii. In the DNA Discover List, verify that the camera's status is Online

and Authenticated.

iv. Configure the camera’s networking settings.

v. Right-click the camera and select IP Setup, or click the IP Setup

icon in the navigation bar.

vi. In the DNA - IP Setup window, you can clear Use DHCP and

specify an IP Address, Mask, and Gateway.

Then, click Update and wait for Ok status to appear.

c. To configure the camera for networking using the camera’s

web page:

d. Open the camera’s web page either by double-clicking the camera in

the DNA Discover List or by typing the camera’s IP address in a web

browser’s address bar.

e. On the login screen, type admin for the user name and the password

for the admin user (default: admin).

Note

When logging in to the camera for the first time or for

the first time after performing a factory default, specify

a new password for the admin user.

Use a strong password consisting of at least 12

characters and at least one uppercase letter, one

lowercase letter, and one number. Passwords can

include the following special characters: |

@#~!$&<>+_-.,*?= .

Log back in with the new password.

The camera's View Settings Home Page opens.

Configuration Steps

CP-6408-21-I QIG

Page

f. Click System Settings.

Make sure the Network page appears.

g. Set network parameters such as static or DHCP IP addressing. If

using static IP addressing, specify the camera's IP, Netmask, and

Gateway. You can also define the Domain Name System (DNS) server

settings

h. Set network parameters such as static or

DHCP IP addressing. If using static IP

addressing, specify the camera's IP,

Netmask, and Gateway. You can also

define the Domain Name System (DNS)

server settings.

Configuration Steps

CP-6408-21-I QIG

Page

i. Click Save. If you have made any changes on the Network page, the

camera reboots.

Note

For more information about configuring the camera for

networking, see the camera’s user guide.

Attach the unit to the same LAN segment as the computer that is managing

the unit. DNA automatically discovers the unit on the network and displays

the device’s current IP address in the Discover List.

4.1 Configuring Host using Static Addresses

If using a Static IP address (as on a Latitude System):

1. Ensue that the DNA DHCP option is NOT selected.

2. Follow the DNA instructions to set the desired IP address.

4.2 Configuring for a DHCP environment

Select the unit from the Discover List.

4.3 Additional Setup Parameters

1. To select PAL or NTSC, select the device in the DNA Discover list, right-click

to open the context menu and click Change Video Format.

2. Click Update.

Attach to VMS

Once you have completed installation and setup and noted the current IP address

with DNA, use your VMS Discovery/Attach procedures to attach the camera to

your VMS.

Camera Dimensions

CP-6408-21-I QIG

Page

5.Camera Dimensions

CP-6408 4K IR PTZ

6.Contact Information

FLIR Systems, Inc.

6769 Hollister Ave.

Goleta, CA 93117

www.flir.com/security

Support Website:

product.enterprise.support@flir.com

Inhaltsverzeichnis

Andere FLIR Sicherheitskamera Handbücher

FLIR

FLIR LOREX LNE3162 Series Bedienungsanleitung

FLIR

FLIR Ariel Gen III CB-330 Series Handbuch

FLIR

FLIR Digimerge DBV44TL Bedienungsanleitung

FLIR

FLIR LOREX LNB4321 Series Bedienungsanleitung

FLIR

FLIR N258F5 Series Bedienungsanleitung

FLIR

FLIR N357B8 SERIES Bedienungsanleitung

FLIR

FLIR FXV101-H Bedienungsanleitung

FLIR

FLIR CP-6302 Bedienungsanleitung

FLIR

FLIR SyncroIP Camera Series Bedienungsanleitung

FLIR

FLIR Quasar CM-6405 Bedienungsanleitung

FLIR

FLIR Saros DM-695-S Bedienungsanleitung

FLIR

FLIR Quasar Gen II Bedienungsanleitung

FLIR

FLIR Quasar CB-6408 Bedienungsanleitung

FLIR

FLIR PT series Bedienungsanleitung

FLIR

FLIR Navigator II Bedienungsanleitung

FLIR

FLIR C23 Series Bedienungsanleitung

FLIR

FLIR Photon Bedienungsanleitung

FLIR

FLIR MD-Series Bedienungsanleitung

FLIR

FLIR FX Bedienungsanleitung

FLIR

FLIR FX Bedienungsanleitung

FLIR

FLIR FC-Series S Bedienungsanleitung

FLIR

FLIR CB-5222 Handbuch

FLIR

FLIR MPX C237VC Bedienungsanleitung

FLIR

FLIR FX Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung