Flotec FP0F360AC Bedienungsanleitung

P.O. Box 342, Delavan, WI 53115

Phone:

1-800-365-6832

Fax:

1-800-526-3757

E-Mail:

info@flotecwater.com

Web Site:

http://www.flotecwater.com

OWNER’S MANUAL

Cyclone Pumping System

NOTICE D’UTILISATION

Système de pompe Cyclone

MANUAL DEL USUARIO

Sistema de bombeo Cyclone

Installation/Operation/Parts

For further operating,

installation, or maintenance

assistance:

Call 1-800-365-6832

English ...................... Pages 2-7

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 365-6832

Français ................. Pages 8-13

Instalación/Operación/Piezas

Para mayor información sobre

el funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-365-6832

Español ...............Paginas 14-19

FP782 (Rev. 2/2/07)

Model FP0F360AC

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

Safety 2

SAFETY INFORMATION

Use this pump only on a 115

volt circuit. Pump is equipped

with an approved 3-conduc-

tor cord and 3-prong, grounding-type

plug. To reduce the risk of electric shock,

connect it to a properly grounded,

grounding-type receptacle.

If circuit has a 2-prong receptacle, replace

it with a properly grounded 3-prong recep-

tacle installed in accordance with the

National Electrical Code and local codes

and ordinances.

Any extension cord used must be outdoor

grade, gauge 16 AWG or heavier, and not

more than 25’ long.

Risk of fire or explosion if

used to pump flammable liquids or if used

in explosive atmospheres. Pump water

only with this pump. Pump is designed

to pump water at temperatures between

32°-77° F (0°-25° C) only.

Risk of electrical shock. Do

not allow the motor to get wet!

Risk of burns. During nor-

mal operation, motor case may heat

enough to burn you. Do not touch motor

when it is hot.

Do not operate the pump continuously at a

discharge pressure of more than 12 psi

(83 kPa) or discharge lift of more than

28’ (8.5 M), as the motor will exceed the

normal safe operating temperature and

may heat to 180° - 190° F (82° C - 88° C).

NOTICE: This unit is not designed for appli-

cations involving salt water or brine! Use

with salt water or brine will void warranty.

Hazardous

voltage

Installation 3

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

OIL THE PUMP

Oil the pump with 1/2 tablespoon food

grade mineral or vegetable oil with each

use. Pour the oil in the ‘IN’ port. Three 1/2

tablespoon oil packets are included.

NOTICE: The pump depends on the liquid

being pumped for lubrication.

DO NOT RUN THE PUMP DRY!

If the pump does not start to move water in

30 seconds or less, recheck the installation

and plumbing.

Mount the pump solidly on a stable

platform.

USE 1/2" HOSE (OR LARGER)

Use a reinforced hose on the inlet. The

pump should be less than 10’ above and

less than 25’ to one side of the water

source. Make the outlet hose as short as

possible – 25’ or less.

Check the washer in the inlet fitting to

make sure it is airtight. If this joint leaks

air, the pump will not operate.

Oil

Do Not Run Pump Dry!

OUT

1/2" or Larger

Outlet Hose

4837A 0205

Water OUT

Water IN

1/2" or Larger

Reinforced

Inlet Hose

Installation 4

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

KEEP THE HOSES AS STRAIGHT

AS POSSIBLE

To reduce friction, do not coil or kink the

hoses. When pumping from a well or

stream, raise the inlet hose a few inches off

the bottom to avoid sucking in sand, silt or

pebbles (which can disable the impeller).

Install a strainer or the Pud-L-ScoopTM

(included only with Model FP0F360AC) to

protect the pump from large solids .

NOTICE: Attach the Pud-L-ScoopTM to the

end of the inlet line and place it in at least

1/2" of water at the lowest point to be

pumped. Be sure all connections are air tight.

INLET HOSE GOES IN THE

WATER; OUTLET HOSE STAYS

OUT OF THE WATER. MOTOR

MUST STAY DRY

Make sure all inlet connections are tight

(no air leaks) and the inlet hose is in the

water. Make sure the end of the outlet hose

not

under water. If the outlet is under

water, the pump may not work.

Plug the cord into a 3-wire, 115 volt,

60 Hz, grounded A.C. outlet.

You should get water in 30 seconds or less.

If not, add more oil and repeat the process.

If your pump does not prime on the sec-

ond try, check the impeller and the inside

of the pump head for wear. Replace as

needed.

In rare cases you may need to prime the

pump. To prime it, fill the suction hose

with water, put it back in the water source,

and start the pump.

The motor must have air circulation

around it for proper cooling. This pump

will lift water 12’; trying to lift water more

than 12’ can cause the motor to run hot.

The motor has a thermal overload which

will stop it if it gets too hot. If the motor

stops, allow it to cool for 30 minutes

before trying to start it again.

No kinks! No Coils!

Straight

Hose!

Water IN

Water OUT

Outlet Hose

Plug in pump to start it.

NOTE: If you don’t get water in

30 seconds or less, add more oil

and repeat the process.

See Step 1.

Inlet Hose

Installation 5

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

UNPLUG THE PUMP

Unplug the pump before all the water is

completely gone.

DO NOT RUN PUMP DRY!

PERFORMANCE

The pump will deliver 350 gallons/1325

liters per hour with an unrestricted dis-

charge line. If the discharge line is restrict-

ed or raised and the pressure on the pump

outlet port increases, it will pump less

water.

NOTICE: This pump’s motor has brushes.

Inspect the brushes frequently; replace

them if they’re worn.

Unplug

SYMPTOM PROBABLE CAUSE(S) CORRECTIVE ACTION

Pump stops without Pump has overheated Wait for overload to reset; pump will automatically

warning and thermal overload restart

has tripped

Discharge hose too long Use shorter hose or reduce lift

or discharge lift higher

than 28’

Pump Won’t Prime Pump body not oiled Add oil through inlet port (see Page 3)

Suction hose too long or Use 1/2"Suction hose, 25’ long or less

too small (the shorter the hose, the better)

Worn impeller Replace impeller

Suction leaks Replace hose washer, check for leaks in hose

Suction hose kinked Straighten out suction hose

or coiled

Pump leaks Shaft U-cup seal leaks Replace shaft seal

Cover O-Ring leaks Replace cover O-Ring

Pump runs, pumps Worn impeller Replace impeller

little or no water Bad motor brushes Replace motor brushes

Bad U-cup shaft seal Replace shaft seal

(pump will leak)

Suction or discharge hose Straighten out hose

kinked or coiled

TROUBLESHOOTING CHART

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

Repair Parts 6

Pump Head Assembly No. RP4940-22

includes Key Nos. 1 through 7.

Service Kit No. FP003414S-01

includes 1 each of Key Nos. 3, 4, and 6.

Brush Kit No. FP003415S

includes a pair of replaceable brushes, springs,

and caps, Key No. 10.

Pud-L-ScoopTM No. FP000349A

includes the Pud-L-ScoopTM, and a 6’ garden

hose with washer.

Key Part

No. Description Qty.

1 10-32x1-3/4 Phil. Hd Screw* 2

2 End Cover / Wear Plate 1

3 O-Ring 1

4 Impeller 1

5 Insert 1

6 U Cup Seal 1

7 Pump Body 1

8 Slinger 1

9 Motor** 1

10 Motor Brush and Spring Set 1 Pair

* Standard hardware item; purchase locally.

** If motor fails, replace entire pump.

MODEL FP0F360AC-09

REPAIR PARTS

Brush must enter

square hole.

Match brush curve

to armature curve

123456 7 89 10

Brush Installation

Warranty 7

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

ATTACH ORIGINAL RECEIPT HERE FOR WARRANTY CONSIDERATION.

FLOTEC warrants to the original consumer purchaser (“Purchaser”) of its products that they are free

from defects in material or workmanship.

If within twelve (12) months from the date of the original consumer purchase any such product shall

prove to be defective, it shall be repaired or replaced at FLOTEC’s option, subject to the terms and con-

ditions set forth below. Your original receipt of purchase is required to determine warranty eligibility.

Exceptions to the Twelve (12) Month Warranty

Product Warranty Period

Drill Pump, Pitcher Pump, 90 days

In-line Water Filter Cartridge

1/3 HP Submersible Sump Pumps

INTELLIPUMP (Model FP0S1775A) 2 Years

Back-up Sump Pump System (Model FP2800DCC)

4" Submersible Well Pumps

1/2 HP Submersible Sump Pumps 3 Years

Models FPSC2200A-10 and FPSC2250A-10

Pre-Charge Water System Tank 5 Years

Models FPSC3200A-10 and FPSC3250A-10

Floodmate®7000 (Model FP0S6000A)

Ironmate®(Model FPSC4550A)

Sewage Ejector (Model FPSE3601A) Lifetime

Pedestal Sump Pump (Model FPPSS5000)

Utility Pump (Model FPSC1725X)

Submersible Sump Pump (Model FPSC4550A-10)

General Terms and Conditions

Purchaser must pay all labor and shipping charges necessary to replace product covered by this

warranty. This warranty shall not apply to acts of God, nor shall it apply to products which, in the

sole judgement of FLOTEC, have been subject to negligence, abuse, accident, misapplication, tam-

pering, alteration; nor due to improper installation, operation, maintenance or storage; nor to other

than normal application, use or service, including but not limited to, operational failures caused by

corrosion, rust or other foreign materials in the system, or operation at pressures in excess of rec-

ommended maximums.

Requests for service under this warranty shall be made by returning the defective product to the

Retail outlet or to FLOTEC as soon as possible after the discovery of any alleged defect. FLOTEC

will subsequently take corrective action as promptly as reasonably possible. No requests for service

under this warranty will be accepted if received more than 30 days after the term of the warranty.

This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective

products.

FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT

DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT

EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED

HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limi-

tations on how long an implied warranty lasts, so the above limitations or exclusions may not apply

to you. This warranty gives you specific legal rights and you may also have other rights which vary

from state to state.

FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115

Phone: 1-800-365-6832 • Fax: 1-800-526-3757

E-Mail: info@flotecwater.com • Web Site: http://www.flotecwater.com

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

Pour les services des pièces ou d'assistance, appeler le service à la clientèle Flotec en composant le 1 (800) 365-6832

Sécurité 8

CONSIGNES DE SÉCURITÉ

Utiliser cette pompe uniquement

sur un circuit de 115 volts. Elle

est équipée d’un câble conduc-

teur à 3 fils métalliques à prise à la masse. Pour

réduire tout risque d’électrocution, le brancher

à un réceptacle correctement relié à la masse.

Si un circuit a un réceptacle à 2 trous, le rem-

placer avec un réceptacle à 3 trous adéquate-

ment mis à la terre et posé conformément aux

normes du National Electric Code, aux codes de

la municipalité et aux décrets applicables.

Si on utilise un cordon prolongateur, il doit être

prévu pour être utilisé à l’extérieur et le calibre de

ses conducteurs doit être de 16 AWG ou plus gros.

Sa longueur ne doit pas dépasser 25 pieds (7,6 m).

Risque d’incendie ou d’ex-

plosion si la pompe est utilisée pour pomper des

liquides inflammables ou si elle est utilisée dans

une atmosphère explosive. Ne pomper que de

l’eau avec cette pompe. La pompe est conçue

pour pomper de l’eau dont la température varie

entre 0 et 25 °C (32 ° et 77 °F) seulement.

Risque d’électrocution. Ne

pas laisser le moteur se mouiller.

Risque de brûlures. Pendant

le fonctionnement normal, le carter du moteur

peut atteindre une température suffisamment

élevée pour causer des brûlures. Ne pas toucher

au moteur pendant qu’il est chaud.

Ne pas faire fonctionner la pompe en continu si

la pression de refoulement est supérieure à 83

kPa (12 lb/po2) ou si la hauteur de refoulement

est supérieure à 8,5 m (28 pi) sinon les tempéra-

tures de fonctionnement sécuritaires normales

de moteur seront dépassées et la chaleur pourra

atteindre 82° C à 88° C (180° F à 190 ° F).

AVIS : Cette pompe n’est pas conçue pour

pomper de l’eau salée ni de la saumure! La

garantie sera annulée si cette pompe est utilisée

pour pomper de l’eau salée ou de la saumure.

ATTENTION

Tension

dangereuse

AVERTISSEMENT

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

Installation 9

Pour les services des pièces ou d'assistance, appeler le service à la clientèle Flotec en composant le 1 (800) 365-6832

HUILER LA POMPE

Huiler la pompe avec 1/2 cuiller à soupe

d’huile végétale de qualité alimentaire ou

d’huile minérale chaque fois qu’on l’u-

tilise. Verser l’huile dans l’orifice repéré

«IN». Trois sachets d’huile de contenance

de 1/2 cuiller à soupe chacun sont fournis.

AVIS : La pompe est lubrifiée par le liquide

qu’elle pompe

NE PAS FAIRE FONCTIONNER LA POMPE

À SEC!

Si la pompe n’a pas commencé à faire cir-

culer l’eau dans 30 secondes ou moins,

revérifier l’installation et la tuyauterie.

Monter la pompe fermement sur une plate-

forme stable.

UTILISER UN TUYAU SOUPLE

DE 1,3 CM (1/2 PO)

(OU PLUS GROS)

Utiliser un tuyau souple renforcé sur le

côté admission. Cette pompe doit être

installée à moins de 3 mètres (10 pieds)

au-dessus de la source d’eau, et à moins

de 7,6 mètres (25 pieds) d’un côté ou

l’autre de la source d’eau. Le tuyau souple

de refoulement doit être aussi court que

possible, soit 7,6 mètres (25 pieds) de long

maximum.

Veiller à ce que la rondelle dans la garni-

ture d’admission soit hermétique. Si ce

joint n’est pas étanche et cause des fuites

d’air, la pompe ne fonctionnera pas.

Oil

Do Not Run Pump Dry!

OUT

1/2" or Larger

Outlet Hose

4837A 0205

Water OUT

Water IN

1/2" or Larger

Reinforced

Inlet Hose

Ne pas faire fonctionner

la pompe à sec!

ENTRÉE

Huile

Tuyau souple de refoulement de

1,3 cm (1/2 po) ou plus gros

Tuyau souple

d’aspiration

renforcé de

1,3 cm (1/2 po)

ou plus gros

SORTIE

de l’eau

ADMISSION

de l’eau

Inhaltsverzeichnis

Sprachen:

Andere Flotec Wasserpumpe Handbücher

Flotec

Flotec Multi-Stage Pump Bedienungsanleitung

Flotec

Flotec 3601A SERIES Bedienungsanleitung

Flotec

Flotec Easy Sump FPRP3250C Bedienungsanleitung

Flotec

Flotec FP5172-08 Bedienungsanleitung

Flotec

Flotec FP0S1300X Bedienungsanleitung

Flotec

Flotec FP0S2000A Bedienungsanleitung

Flotec

Flotec FPSC1725X Bedienungsanleitung

Flotec

Flotec VIP 180/7 Bedienungsanleitung

Flotec

Flotec FP0S6000A Bedienungsanleitung

Flotec

Flotec Autojet60 Bedienungsanleitung

Flotec

Flotec FPZT7300 Bedienungsanleitung

Flotec

Flotec FPSC1725X Bedienungsanleitung

Flotec

Flotec FPZS25T Bedienungsanleitung

Flotec

Flotec GARDENJET 1000 Bedienungsanleitung

Flotec

Flotec E50TLT Bedienungsanleitung

Flotec

Flotec FP5722 Bedienungsanleitung

Flotec

Flotec FPSE3500A Bedienungsanleitung

Flotec

Flotec FPUS1860A Bedienungsanleitung

Flotec

Flotec FP6005 Bedienungsanleitung

Flotec

Flotec FP5100 Bedienungsanleitung

Flotec

Flotec 1100X Series Bedienungsanleitung

Flotec

Flotec VIP 130/6 Bedienungsanleitung

Flotec

Flotec FP5712 Bedienungsanleitung

Flotec

Flotec FP0S1790PCA Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung