Fluke 17 Series Bedienungsanleitung

PN 5382413 (English)

10/2022

subject to change without notice. All Product names are

trademarks of their respective companies.

17xx Clamp Adapter

BNC Adapter for Clamps

Instructions

Introduction

The 17xx Clamp Adapter is an accessory for the 17xx-series

of Power Quality Analyzers. Use the adapter to connect the

current clamp with the BNC connector to the 17xx Analyzer.

This adapter is ready-to-use for all clamps with a ratio of

1 mV/A. Select the adapter version depending on the voltage

output of the clamp:

Maximum 1 V: Supports clamps with a range from

0.2 A RMS to 1000 A RMS or up to ±1500 A DC

Maximum 2.8 V: Supports clamps with a range from

4 A RMS to 2800 A RMS or up to ±4000 A DC

See Supported Clamp Models for the required measurement

configuration on the 17xx Analyzer and a clamp with a ratio

other than 1 mV/A.

Connector to 17xx Analyzer

Label with maximum clamp output voltage

BNC connector to Clamp cable

FLUKE 17XX

Clamp

Adapter

Contact Fluke

Fluke Corporation operates worldwide. For local contact

information, go to our website: www.fluke.com.

To register your product, or to view, print, or download the

latest manual or manual supplement, go to our website.

+1-425-446-5500 fluke-info@fluke.com

Safety Information

A Warning identifies hazardous conditions and procedures

that are dangerous to the user. A Caution identifies

conditions and procedures that can cause damage to the

Product or the equipment under test.

XW Warning

To prevent possible electrical shock, fire, or

personal injury:

Read all safety information before you use the

Product.

Do not alter the Product and use only as

specified, or the protection supplied by the

Product can be compromised.

Comply with local and national safety codes. Use

personal protective equipment (approved rubber

gloves, face protection, and flame-resistant

clothes) to prevent shock and arc blast injury

where hazardous live conductors are exposed.

Do not use the Product around explosive gas or

vapor.

Do not touch voltages >30 V ac rms, 42 V ac peak,

or 60 V dc.

Before each use, examine the Product. Look for

cracks or missing pieces of the connectors or

cable insulation. Also look for loose or weakened

components.

Fluke Corporation

P.O. Box 9090

Everett WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

Do not use a current measurement as an

indication that a circuit is safe to touch. A voltage

measurement is necessary to know if a circuit is

hazardous.

Have an approved technician repair the Product.

Remove the input signals before you clean the

Product.

Do not apply more than 5 Vpk to the adapter

Use the product only with compatible current

clamps. See Supported Clamp Models.

Symbols

The table below lists the symbols that can be used on the

Product or in this document.

Symbol Description

»Consult user documentation.

WWARNING. RISK OF DANGER.

XWARNING. HAZARDOUS VOLTAGE. Risk of

electric shock.

This product complies with the WEEE Directive

and its marking requirements. The affixed label

indicates that you must not discard this

electrical/electronic product in domestic

household waste. Do not dispose of this

product as unsorted municipal waste. For

information about take-back and recycling

programs available in your country, see the

Fluke website.

Supported Clamp Models

Sensitivity Range Adapter Scale

Factor Range

i1000s AC

100 mV/A

10 mV/A

1 mV/A

0.1 A to 10 A

0.1 A to 100 A

1 A to 1000 A

1 V 0.01:1

0.1:1

1:1

Auto

i3000s AC

10 mV/A

1 mV/A

0.1 mV/A

1 A to 30 A

1 A to 300 A

1 A to 3000 A

1 V 0.1:1

1:1

10:1

Auto

i310s AC/DC[1]

10 mV/A

1 mV/A

30 A

300 A

1 V 0.1:1

1:1 Auto

i400s AC

10 mV/A

1 mV/A

0.5 A to 40 A

5 A to 400 A 1 V 0.1:1

1:1 Auto

80i-110s AC/DC[1]

100 mV/A

10 mV/A

0.1 A to 10 A

0.1 A to 100 A 1 V 0.01:1

0.1:1 Auto

i200s AC

10 mV/A up to 200 A

+10 % 2.8 V 0.1:1 Low

i30s AC/DC[1]

100 mV/A up to 28 A

+10 % DC 2.8 V 0.01:1 Low

i5s AC

400 mV/A 5 A 2.8 V 0.0025:1 Low

[1] DC is only supported by the 177x PQ Analyzers.

Instructions

Note

The adapter is compatible only with clamps. Flexis,

such as the i430-Flexi-TF-II, are not supported.

To u s e :

1. Connect the adapter to the clamp and attach the adapter

to the 17xx Analyzer.

2. Apply the required scaling factor and range that is

specific for the attached clamp.

Note

Fluke strongly recommends to use the low range

with the 2.8 V adapter. The higher range may distort

the signal.

FLUKE 17XX

Clamp

Adapter

Specifications

Cable length ................................175 mm

Connectors..................................BNC female to 4-pin connector

for current input of Fluke 17xx

series

Te m p e r a t u re

Operating ...............................-25 °C to +70 °C

(-13 °F to +158 °F)

Storage ...................................-40 °C to +80 °C

(-4 °F to +176 °F)

Humidity .......................................15 % to 85 %, noncondensing

Operating Humidity ..................≤90 % RH (at 10 °C to 30 °C)

≤75 % RH (at 30 °C to 40 °C)

≤45 % RH (at 40 °C to 50 °C)

LIMITED WARRANTY

This Fluke product will be free from defects in material and

workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries, or

damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the

warranty period, contact your nearest Fluke authorized

service center to obtain return authorization information,

then send the product to that Service Center with a

description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do

not allow the exclusion or limitation of an implied warranty or

of incidental or consequential damages, this limitation of

liability may not apply to you.

11/99

Inhaltsverzeichnis

Andere Fluke Adapter Handbücher

Fluke

Fluke 1736 Bedienungsanleitung

Fluke

Fluke Norma Star Point Betriebsanleitung

Fluke

Fluke DTX-COAX Bedienungsanleitung

Fluke

Fluke 5320A-LOAD Bedienungsanleitung

Fluke

Fluke DTX-PC6AS Bedienungsanleitung

Fluke

Fluke BC430/830 Bedienungsanleitung

Fluke

Fluke BC190/830 Bedienungsanleitung

Fluke

Fluke BC190 Bedienungsanleitung

Fluke

Fluke 17XX-CLAMP-ADPT-2V8 Bedienungsanleitung

Fluke

Fluke DTX-MFM2 Bedienungsanleitung

Fluke

Fluke BC500 Bedienungsanleitung

Fluke

Fluke DTX-PLA002PRP Bedienungsanleitung

Fluke

Fluke DSP-PM11A Bedienungsanleitung

Fluke

Fluke 174x Bedienungsanleitung

Fluke

Fluke BC190/830 Bedienungsanleitung

Fluke

Fluke DSP-FTA440S Bedienungsanleitung

Fluke

Fluke Norma Star Point Bedienungsanleitung

Fluke

Fluke BC190/820 Bedienungsanleitung

Fluke

Fluke ir3000 FC Bedienungsanleitung

Fluke

Fluke BC190/830 Bedienungsanleitung

Fluke

Fluke BC430/830 Bedienungsanleitung

Fluke

Fluke ir3000 Bedienungsanleitung

Fluke

Fluke DSP-FTA410 Bedienungsanleitung

Fluke

Fluke Zero Adapter Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung