foc.us Emifocus Bedienungsanleitung
Tested by OMNI-Test Laboratories, Inc. and approved to
UL 737-2011 and ULC S627-00
US EPA exempt
Report Number : 0304WF008S
This document was packed with the appliance.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
EMIFOCUS
____
DESIGN INSTALLATION &
OPERATING MANUAL
2
Introduction
Table
of contents
Please read this entire manual before you install and use
your focus fireplace. Failure to follow instruction may result
in property damage, bodily injury or even death. When this
room heater is not properly installed, a house fire may result.
To reduce the risk of fire, follow the installation instructions.
Contact local building or fire officials about restrictions and
installation inspection requirements in your area.
This fireplace is approved for use as a wood burning
fireplace or for use with a vented gas log listed to
ANSI Z21.60 standard having an input rate of 65,000
Btu or less.
KEEP THIS MANUAL HANDY FOR EASY REFERRAL.
All WARNING and CAUTION statements will appear in bold
font and upper case letters: THEY SHOULD BE STRICTLY
OBSERVED.
Thank you for choosing focus fireplaces.
Appliance designation: émifocus d.v.
Manufacturer:
Focus - Atelier Dominique Imbert
Le fort – 34380 Viols le fort – France.
Introduction
Specifications
CHARACTERISTICS
ROOF OUTLET REQUIREMENT
CHIMNEY REQUIREMENT
STRUCTURAL REQUIREMENT
CONNECTOR
FRESH AIR INTAKE
CLEARANCES TO COMBUSTIBLES
A. CLEARANCES TO FLOOR AND CEILING
B. CLEARANCES TO SIDE WALLS
Installation
INCLUDED PARTS, MATERIALS AND REQUIRED TOOLS
FOR INSTALLATION
OPTIONS
ASSEMBLY DETAILS
A. SIDE CUT PLATE DETAIL
B. WALL MOUNTING INSTALLATION
C. FLUE PIPE INSTALLATION
D. INSULATED CHIMNEY CONNECTION TO FOCUS FLUE
Operating instructions
STORAGE / USE OF FLAMMABLE LIQUIDS
GRATE
ASHES
FUEL
FIRE SCREEN
BEFORE LIGHTING YOUR FIRST FIRE
BUILDING, STARTING AND MAINTAINING THE FIRE
PROTECTIVE GLOVE
Maintenance
TAKING OUT THE ASHES
CREOSOTE FORMATION AND NEED FOR REMOVAL
SWEEPING YOUR CHIMNEY
SURFACES
REPLACEMENT PARTS
Warranty
Annex
HOW TO DETERMINE IF ALTERNATE FLOOR PROTECTION
MATERIALS ARE ACCEPTABLE
2
3
3
4
4
5
5
5
6
8
8
8
8
12
12
12
12
12
13
13
14
14
15
15
15
15
16
16
16
17
17
3
Specifications
CAUTION
NOT FOR MOBILE HOME INSTALLATION!
DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM!
NOT TO INSTALL WITH MASONRY CHIMNEY SYSTEM.
DO NOT INSTALL IN SLEEPING ROOM.
•The authority having jurisdiction (such as municipal building department, fire department, fire prevention
bureau, etc.) Should be consulted before installation to determine the need to obtain a permit.
•Using make-shift compromises during installation can cause damage. Such installation is not covered under
focus limited warranty.
•When this room heater is not properly installed, a house fire may result. To reduce the risk of fire, follow the
installation instructions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
CHARACTERISTICS
• Hearth weight: 115 lbs
(52 kg)
• Flue diameter: 8-5/8-inch
(219mm) ;
length custom-made
• Flue weight: 11 lbs per foot
(16 kg per meter)
• Wall anchor plate weight:
approx. 22 lbs (10 kg)
• 1/8-inch (3 & 2.5 mm) thick
steel
• High heat resistant paint
• Guarranteed efficiency
with a minimum flue lenght
(interior and exterior) of 10
feet (3.00m)
• Fire screen
EMIFOCUS
Scale 1 : 20
Note : imperial are rounded from metric
floor
(sol)
8’’ adaptor
Ø 27 9/16"
(Ø 700 mm)
30 1/2"
(775 mm)
24"
(610 mm)
65 9/16"
(1.665 mm)
5 11/16"
(145 mm)
11 7/16"
(290 mm)
Ø 8 5/8" id
(Ø 219 mm)
Ø 8 1/16" id
(Ø 205 mm)
42 1/2"
(1.080 mm)
20"
(500 mm)
16 9/16"
(420 mm)
4
Specifications
ROOF OUTLET REQUIREMENT
CHIMNEY REQUIREMENT
Do not connect this unit to a chimney flue serving another appliance!
Émifocus requirement: the total length of flue (inside + outside) must be 10 feet minimum (13 feet for an installation less than
3 miles from the ocean or if a 30° elbow is necessary).
The émifocus must be connected to a chimney complying with the requirements for Type HT chimneys in the standard for
Chimneys, Factorybuilt, Residential Type and Building Heating Appliance, UL 103. For example, a class A insulated stainless
steel flue chimney system with an 8-inch minimum inside diameter.
5
Specifications
STRUCTURAL REQUIREMENT
CAUTION
THE FRAMING SUPPORTING THE ANCHOR PLATE (WALL STRUCTURE, PARTITION, ETC.) MUST BE SIZED IN
CONGRUENCE WITH THE FIREPLACE STATIC AND DYNAMIC CHARGES. THE SIZE CALCULATION FOR THE
SUPPORT IS NOT THE RESPONSIBILITY OF FOCUS OR ITS AFFILIATES. IT IS YOUR RESPONSIBILITY TO
CONSULT WITH AN ENGINEER OR ARCHITECT FOR YOUR PROJECT.
CONNECTOR
Connectors are all non-insulated chimney parts including focus flue, focus 8’’ universal adaptor and the chimney manufacturer
finishing collar with adapter.
To avoid heat traps the chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or
a floor, or ceiling.
Passage through an attic, roof frame floor, or ceiling must be done using an insulated chimney respecting all chimney
manufacturer clearances.
CAUTION
PASSAGE THROUGH A WALL OR PARTITION OF COMBUSTIBLE CONSTRUCTION IS NOT AN APPROPRIATE
INSTALLATION FOR THIS FOCUS FIREPLACE.
FRESH AIR INTAKE
For optimum functioning, focus requires a fresh air intake in the room (ideally at the back of the fire). We recommend deflect-O
A0684 semi rigid aluminium duct. The wall plate is supplied with a fresh air control.
Minimum fresh air intake size:
fresh air intake
This fresh air intake is compulsory
when operating venting appliances
such as kitchen hoods, permanent
air extractors or any appliances
creating an air depression in the
habitation.
IMPORTANT
6
CLEARANCES TO COMBUSTIBLES
A. CLEARANCES TO FLOOR AND CEILING
minimum 8’-6’’
minimum 2.60 m
IMPORTANT
no radiant floor heating tubing under the fireplace !
pas de chauffage au sol !
non combustible surface R ≥ 1.2
surface non combustible R ≥ 1.2
combustible sub floor
sol combustible
20’’
50 cm
8’’
200 mm
8’’
200 mm
16’’ / 40 cm (US)
18’’ / 45 cm (Canada)
wall
mur
wall
mur
non combustible surface R ≥ 1.2
surface non combustible R ≥ 1.2
Specifications
7
B. CLEARANCES TO SIDE WALLS
1/2’’cement board
(Durarock)
13 mm panneau de ciment
(Durarock)
1’’ rockwool insilation
(Roxul) attached to
backside of cement board.
25 mm isolant laine de roche (Roxul)
positionné juste derrière le panneau de ciment.
2x6’’ metal studs supporting
wall mounting plate.
montants métal 2x150 mm
supportant la platine murale
combustible wall
mur combustible
2’’
50 mm
1/2’’
12 mm
26’’
660 mm
36’’
915 mm
combustible wall
mur combustible
4’
1220 mm
CAUTION
THE DISTANCE TO A COMBUSTIBLE WALL MUST BE MAINTAINED AT 26 INCHES. PROPERTY DAMAGE OR
DEATH CAN OCCUR IF THIS DISTANCE IS NOT MAINTAINED. DRYWALL PRODUCTS LINED WITH PAPER
SUCH AS SHEETROCK ARE COMBUSTIBLE. CLEARANCES AS INDICATED FURTHER APPLY.
Manufacturer specifications:
• Corner configuration: this configuration necessit that you build an additional wall in the corner of the room. When placed
close to a noncombustible wall leave a minimum of 4 inches (from hearth which has a 27-9/16” diameter) for proper
ventilation. To avoid premature aging of your painted walls, only use mineral paint. With other paints, 38” clearances apply.
• Fire clearance to glass (from hearth): 31-1/2”.
• Fire clearance to vinyl windows: refer to window technical specifications..
IMPORTANT
Clearances may only be reduced by means approved by the regulatory authority.
Specifications
8
Installation
INCLUDED PARTS, MATERIALS AND REQUIRED TOOLS FOR INSTALLATION
• Appliance and designated parts are the hearth, grate, wall mounting anchor plate, black steel flue pipe, focus kit
(protective glove, mounting gloves, can of touch-up paint).
• Required tools: drill, M8 allen key, level, screwdrivers, M12 key, scaffolding, refractory compound.
• 2 persons minimum are required for installation.
OPTIONS
• Custom ceiling cover disc (steel disc) + cover disc screw kit
• Focus steel flue extension
ASSEMBLY DETAILS
A. SIDE CUT PLATE DETAIL
metal studs frame
structure métalliques
1’’ rock wool
25 mm laine de roche
coupe de côté du émifocus
ambient air
air ambiant 1/2’’
12 mm
cement board
panneaux de ciment
fresh air intake
arrivé d’air frais
9
Installation
B. WALL MOUNTING INSTALLATION
24-13/16’’
630 mm
7 - 7/8’’
200 mm
6’’ diameter
Ø150 mm
b: fresh air intake
arrivé d’air frais
10
Installation
C. FLUE PIPE INSTALLATION
6-7/32’’ ≥ X ≥ 6-1/2’’
160 mm ≥ X ≥ 165 mm
6’’ diameter
Ø150 mm
damper
clé de tirage
fresh air
intake adjustement
ajustement de
l’arrivé d’air frais
7-7/8’’
200 mm
24-13/16’’
630 mm
Inhaltsverzeichnis
Andere foc.us Kamin im Innenbereich Handbücher
foc.us
foc.us néofocus Bedienungsanleitung
foc.us
foc.us Slimfocus mural Bedienungsanleitung
foc.us
foc.us omegafocus Bedienungsanleitung
foc.us
foc.us Heterofocus 1400 Bedienungsanleitung
foc.us
foc.us Drumfocus M-B-C Handbuch
foc.us
foc.us pictofocus 860 Bedienungsanleitung
foc.us
foc.us Slimfocus pivotant Bedienungsanleitung
foc.us
foc.us Gyrofocus Benutzerhandbuch
foc.us
foc.us Meijifocus Bedienungsanleitung
foc.us
foc.us édofocus 630 dv Bedienungsanleitung
foc.us
foc.us Gyrofocus Original Betriebsanleitung
foc.us
foc.us pictofocus 1200 Bedienungsanleitung
foc.us
foc.us Gigafocus 1500 Bedienungsanleitung
foc.us
foc.us agorafocus 850 suspendu Bedienungsanleitung
foc.us
foc.us Filiofocus 1600 Bedienungsanleitung
foc.us
foc.us édofocus 630 d.a. Bedienungsanleitung
foc.us
foc.us Eurofocus 951 pivotant Bedienungsanleitung
foc.us
foc.us ERGOFOCUS Bedienungsanleitung
foc.us
foc.us édofocus 850 d.v. Bedienungsanleitung
foc.us
foc.us agorafocus 630 suspendu Bedienungsanleitung
